Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Black & Decker BES701
Summary of Contents for Black & Decker BES701
- Page 1 BES701 www.blackanddecker.co.nz...
- Page 3 11 26 10 12 10...
- Page 4 9 32...
- Page 7 12 11...
-
Page 8: Intended Use
ENGLISH (Original instructions) Intended use Your BLACK+DECKER BES701 sliding compound mitre saw has been designed for sawing wood, plastic and nonferrous metal only. This tool is intended for non professional users. Safety instructions General power tool safety warnings Warning! Read all safety warnings, instructions, illustrations and specifications provided with power tool. -
Page 9: Safety Instructions For Mitre Saws
(Original instructions) ENGLISH 3. Personal safety Power tools are dangerous in the hands of untrained a. Stay alert, watch what you are doing and use common users. sense when operating a power tool. Do not use a e. Maintain power tools and accessories. Check for power tool while you are tired or under the influence misalignment or binding of moving parts, breakage of of drugs, alcohol or medication. -
Page 10: Kerf Plate Replacement
ENGLISH (Original instructions) saw head and pull it out over the workpiece without workpiece to shift during the cutting operation pulling you cutting, start the motor, press the saw head down and and the helper into the spinning blade. push the saw through the workpiece. The cut-off piece must not be jammed or pressed by any means against the spinning saw blade. -
Page 11: Residual Risks
(Original instructions) ENGLISH Do not work with material containing asbestos. Asbestos Before using or fitting any accessory consult the instruc- is considered to be carcinogenic. tion manual. The improper use of an accessory can cause Wear gloves when handling saw blades and rough damage. -
Page 12: Voltage Drops
ENGLISH (Original instructions) risks can not be avoided. These include: Do not stare at operating lamp Injuries caused by touching any rotating/moving parts. Impairment of hearing. Risk of accidents caused by the uncovered parts of the Do not expose to rain. rotating saw blade. -
Page 13: Removing The Blade
(Original instructions) ENGLISH 18. Main handle When the dust bag (23) is about half full, remove it from 19. Trigger switch the tool. 20. Safety release lever Empty the dust bag of its contents, tapping it lightly so as 21. Cut line light on/off button to remove particles adhering to the insides which might 22. -
Page 14: Installing A Blade
ENGLISH (Original instructions) Switch action (Fig. screw (13a). (Turn clockwise, left-hand threads.) Remove the blade screw (13a), outer clamp washer Caution! Before plugging in the tool, always check to see that (13d), blade (13) and blade adapter (13e), if used. The the switch trigger (19) actuates properly and returns to the inner clamp washer (13f) may be left on the spindle. - Page 15 (Original instructions) ENGLISH match the angle as close as possible. Cut the wood a little too broad flat side on the table and the narrow edge against the long and measure from the pencil line to the cut edge to fence.
- Page 16 Alternative method for cutting crown molding Material up to 70 mm can be cut as described above. BES701 - 70 mm for 216 mm Place the molding at an angle between the fence (12) and the saw table (11), with the top side of the molding on the table...
-
Page 17: After Use
(Original instructions) ENGLISH Troubleshooting NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD OPEN WHEN OPERATING THIS SAW. Problem Possible Cause Solution Warning! Always be sure that the tool is switched off and Motor does Saw not plugged in. Check that all cords are plugged in. unplugged before adjusting or checking the tools function. -
Page 18: Technical Data
Max. dept cut at 45 ° The undersigned is responsible for compilation of the BES701 - Level of sound pressure according to EN 62841: technical file and makes this declaration on behalf of (sound pressure) 98 dB(A), Uncertainty (K) 3 dB(A) Black &... - Page 19 Australia & New Zealand Stanley Black & Decker www.blackanddecker.com.au www.blackanddecker.co.nz Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ) 810 Whitehorse Road Box Hill VIC 3128, Australia...
- Page 20 NA161526 02/2022...