Manual Operation; General Information; Warranty Conditions - Honeywell PEHA 940/8 DALI-G Installation Manual

oPErATIon AnD FUnCTIonS

MAnUAL oPErATIon

operation
 Press on briefly
 Press on for a long time
 Press off briefly
 Press off for a long time
Press Channel
Press Test
LAMP FAULT TEST
The DALI gateway automatically performs a lamp fault test every 60s or when triggered ma-
nually by pressing the Test button. Defective illumination is indicated with the LED display
for the control channels:
Control channel LED display (lamp fault test)
Flashing red Lamp fault, control channel switched off
green/red Lamp fault, control channel switched on
Orange/red Lamp fault, control channel switched on manually
note: The DALI Gateway can show at which control channel the lamp fault appeared. This
does not show which DALI operating device or illuminant is affected.
PHC-FUnCTIonS
The PHC function programming of the DALI module must be performed in the PHC software.
The following functions are available:
output functions
Switch on at max brightness, with memory
Switch on at max brightness without memory
Switch on memory light value
Switch off dimmer
Switch over at max. brightness ON/OFF
Switch over at max. brightness ON/OFF without memory
Switch over at memory value ON/OFF
Switch over / OFF (individually)
Switch over value1/value2
Shutdown warning
Approach dim value
Dim in the opposite direction
Dim up
Dim down
Dim up (relatively)
Dim down (relatively)
Save memory
Stop dimming/time abort/save
Switch on delay
Switch off delay
Switch over delay ON/OFF
Switch over delay value1/value2
Switch-on with timer
Switch-off with timer
Switch-over with timer ON/OFF
Switch-over with timer value1/value2
Lock dim channel
Unlock dim channel
Input functions
Output switched on
Output switched off
Dimvalue reached
Dimm brighter - desired value reached
Dimm darker - endvalue reached
Lamp fault detected
Lamp fault cleared
PEHA_M_940_8_DALI_G (Rev03_130115)
Function
Switch on illumination at max. value
Turn lighting brighter
Turn off illumination
Turn lighting darker
Single activation of control channel 0-7
Lamp fault test control channel 0-7
PHC-SoFTWArE
creAte mOduLe
The DALI Gateway is created using:
„PHC-components  Module list  Dimmermodule"
(see also chapter 3.1.2 of the PHC manual).
mOduLe Addresse
The module address is set using:
„PHC-components  Module list  Details"
(see also chapter 3.2.3 of the PHC manual).
rESET-STATUS (Por)
The reset status of the channels (OFF, Memory and ON) can be set in the PHC software when
the module is switched on. The reset status is set using:
„PHC-components  Module  Channels"
The reset status if preset to "OFF", The "Memory" switching condition is selected if, for exa-
mple, the module is to be given the previous switching condition after a voltage interruption
(> 50 ms) or reset.
TroUBLESHooTInG (ELECTrICIAn)
nEW SySTEM or ExISTInG SySTEM
• Check circuit breaker and power supply.
• Check connected electrical loads and connection cables.
• Check DIP switch.
• Check PHC programming and transfer again.
STATUS DISPLAy
Status LED = out: Check operating voltage (230-240V~)
Status LED = red: Check DIP switch
Status LED = orange: Check PHC bus lines
cOntAct
Telephone: ......................... +49 (0)2351 185-0
Telefax: .............................. +49 (0)2351 27666
PHC-Support: ..................... +49 (0)2353 9118 333
Internet: ............................ www.peha.de
E-Mail: ............................... peha@peha.de

GEnErAL InForMATIon

DISPoSAL oF THE DEVICE
Do not dispose of old devices in the household waste! The device must be disposed
of in compliance with the laws and standards of the country in which it is operated!
The device contains electrical components that must be disposed of as electronics
waste. The enclosure is made from recyclable plastic.

WArrAnTy ConDITIonS

These operating instructions are an integral part of both the device and our terms of war-
ranty. They must be handed over to the user. The technical design of the appliance is subject
to change without prior notification. PEHA products are manufactured and quality-checked
with the latest technology according to applicable national and international regulations.
Nevertheless, if a product should exhibit a defect, PEHA warrants to make remedy as follows
(regardless of any claims against the dealer to which the end user may be entitled as a result
of the sales transaction):
In the event of a justified and properly established claim, PEHA shall exercise its prerogative
to either repair or replace the defective device. Further claims or liability for consequential
damage are explicitly excluded. A justifiable deficiency is deemed to exist if the device exhi-
bits a structural, manufacturing, or material defect that makes it unusable or substantially
impairs its utility at the time it is turned over to the end user. The warranty does not apply
to natural wear, improper usage, incorrect connection, device tampering or the effects of
external influences. The warranty period is 24 months from the date of purchase by the end
user from a dealer and ends not later than 36 months after the device's date of manufac-
ture. German law shall be applicable for the settlement of warranty claims.
126466-01
PEHA Elektro GmbH & Co. KG
Postfach 1727 • D-58467 Lüdenscheid • Internet: www.peha.de
GB - 3