Honeywell NFS-3030 Installation And User Manual
Hide thumbs
Also See for NFS-3030:
- Canadian addendum (4 pages) ,
- Product installation document (18 pages) ,
- Wiring manual (80 pages)
Related Manuals for Honeywell NFS-3030
Summary of Contents for Honeywell NFS-3030
- Page 1 Honeywell Connected Life Safety Services GLSS Gateway Installation and User’s Manual LS10237-000NF-E | REV. A | 31/01/2020...
-
Page 2: Table Of Contents
1.5: FCC STATEMENT...................................6 1.6: Warnings and Cautions................................6 1.7: Disclaimer......................................6 Section 2: Overview................................7 2.1: Operations......................................7 2.2: Honeywell Connected Life Safety Services........................7 2.3: The Gateway Board’s Layout..............................7 2.3.1: Connecting Interfaces ..............................8 2.3.2: LED Indicators..................................9 2.3.3: Switches on the Gateway Board ..........................11 Section 3: Installation...............................12 1.1: Wall Mounting the Dedicated Gateway..........................12... - Page 3 Table of Contents Section 5: Post-Installation Activities .........................22 5.1: Maintenance Testing................................22 5.2: Upgrading the Gateway Firmware............................22 5.2.1: To Upgrade to a Later Release ..........................22 5.2.2: To Verify the Upgrade..............................23 5.2.3: LED Indications During the Upgrade........................23 5.3: Troubleshooting..................................24 5.3.1: To Troubleshoot LED-Indicated Issues........................24 5.3.2: To Troubleshoot Other Issues...........................25 Appendix A: Gateway Operating Conditions ......................26 Appendix B: Modulations and Power Used.........................27...
-
Page 4: Section 1: General Information
Section 1: General Information 1.1 About This Manual This GLSS Gateway Installation and User’s Manual provides detailed procedures about installation, deployment, and upgrade of Honeywell Connected Life Safety Services. The manual describes: • the dedicated CCM gateway, • its installation environment, •... -
Page 5: Documentation Feedback
Documentation Feedback Product Type: Honeywell Connected Life Safety Services Gateway Operate the NFS-3030 NFS-3030 Operational Manual panel 51345 NFS2-3030 Panel Install the NFS2-3030 NFS2-3030 Installation Manual panel 52544 Customize the NFS2- NFS2-3030 Programming Manual 3030 panel 52545 Operate the NFS2-... -
Page 6: Fcc Statement
FCC STATEMENT 1.5 FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including, an interference that may cause undesired operation. -
Page 7: Section 2: Overview
The connection with Cloud facilitates remotely monitoring and managing the fire detection systems. 2.2 Honeywell Connected Life Safety Services The software suite enables remote management of fire detection systems. It monitors the building’s fire system events in real-time and notifies users about the events immediately. -
Page 8: 1: Connecting Interfaces
The Gateway Board’s Layout 2.3.1 Connecting Interfaces uses numbered labels to show the location of the interfaces for connections. This manual uses Figure 2.1 these numbered labels at various places for your convenience. The table below uses these numbered labels to describe the type and usage of the interfaces. Table 2.1: Gateway Interface Details Label Interface Type... -
Page 9: 2: Led Indicators
The Gateway Board’s Layout 2.3.2 LED Indicators The LED indicators on the GLSS Gateway board use different colors to identify various operational status of the gateway. To know the location of the LED indicators on the gateway board, refer Figure 2.1: “Printed Circuit Board: Layout”... - Page 10 The Gateway Board’s Layout Table 2.2: LED Indicators and Their Messages Power-Indicating LED Indicates that the gateway board is using the received power. ON The circuit board is receiving its 24V power from its power source. OFF The circuit board is not receiving the power. LTE Power LED Indicates power supply for the cellular communications.
-
Page 11: 3: Switches On The Gateway Board
The Gateway Board’s Layout Cellular Connectivity Indicates the gateway connectivity status with cellular devices. FLASHING SLOW (flashes per 1 second). The cellular connectivity is enabled for the Cloud connection. OFF The cellular connectivity is disabled. 2.3.3 Switches on the Gateway Board Below table describes about the switches on the gateway board. -
Page 12: Section 3: Installation
Section 3: Installation You can use a fixed gateway or a portable gateway in the fire detection system. Fixed gateway: Permanently connects the gateway with the building’s fire detection system Portable gateway: Helps to configure the fire detection system and synchronizes data CAUTION: THE GATEWAY MUST BE INSTALLED INDOORS. - Page 13 Wall Mounting the Dedicated Gateway 9. Mark and pre-drill the hole for the top keyhole mounting bolt. Figure 3.2: Backside of the Gateway Enclosure 10. Remove the backbox. 11. In the top mounting hole, insert the mounting screw. 12. Tighten the screw, leaving required space for hanging the enclosure. 13.
-
Page 14: Gateway Board Connections
Gateway Board Connections 3.2 Gateway Board Connections The gateway board can be connected with a CLSS Cloud, a configuration computer, a panel, a mobile device, and an external power supply. Wireless Connection CLSS Cloud Ethernet Connection Configuration Computer Mobile Connection Fire Alarm Panel Figure 3.3: Gateway Connections... -
Page 15: 1: Connecting To A Fire Alarm Panel
Each variant of the Notifier panel offers various connection options. The gateway operates only with these Notifier fire alarm control panels listed in the below table: Table 3.2: Connection Options Fire Alarm Panel Models (RS232) NCA-2 NFS-320 NFS-640 NFS2-640 NFS-3030 NFS2-3030 NCM-W NCM-F HSNCM-W HSNCM-MF HSNCM-SF HSNCM-WMF HSNCM-WSM... -
Page 16: To Make A Usb Connection
Gateway Board Connections To Make a USB Connection On the Gateway Side 1. Connect the USB-C side of the cable to the USB port of the gateway. The USB port is labeled as 8 in the figure “Gateway Connections” on page 14 On the Panel Side 1. - Page 17 Gateway Board Connections Figure 3.5: UART/TTL Connections...
-
Page 18: Section 4: Configurations
1. In the mobile device, from Play Store or App Store, download the Connected Life Safety Services app. 2. Install the app. 3. From the Honeywell on-boarding email, take the login credentials. 4. On the mobile, log into the CLSS app. - Page 19 Gateway Configurations 10. Tap on the specific building. 11. To commission the gateway, tap on CONNECT GATEWAY and follow the on-screen instructions.
-
Page 20: Verifying The Gateway Connections
10 5.3, "Troubleshooting" fix it or contact Honeywell technical support. 4.4 Testing the Commissioning After all the CLSS app configurations are done, if required, you can perform a commissioning test. NOTE: The commissioning test does not generate reports. - Page 21 Testing the Commissioning 5. Follow the on-screen instructions.
-
Page 22: Section 5: Post-Installation Activities
15. Start the test. 5.2 Upgrading the Gateway Firmware Honeywell periodically releases updates and upgrades to the gateway’s firmware. Using the Gateway Configuration tool you can securely make the firmware upgrade to the gateway. 5.2.1 To Upgrade to a Later Release 1. -
Page 23: 2: To Verify The Upgrade
If the LED is indicating differently, refer Table 2.2, “LED Indicators and Their Messages,” on page 10 know the operational status. If there is an issue, refer to the section to fix it or 5.3, "Troubleshooting" contact Honeywell technical support. -
Page 24: Troubleshooting
5.3 Troubleshooting Issues that may occur during the gateway’s operation can be resolved on your own or by contacting Honeywell technical support. The issues can be either LED-indicated issues or other issues. 5.3.1 To Troubleshoot LED-Indicated Issues When an LED status indicates issues, refer to the below table to know their possible fixes. -
Page 25: 2: To Troubleshoot Other Issues
Troubleshooting DL3: Panel LED-Indicated Issues Panel LED Status Other LEDs’ Status Possible Fixes Check the following and correct if • DL2 The Trouble LED is OFF necessary: • The cable connections at the gateway board side and at the panel side •... -
Page 26: Appendix A: Gateway Operating Conditions
Appendix A: Gateway Operating Conditions Table B.1: Operational Requirements Power Requirements Nominal voltage range Consumes 12V to 40V DC from the panel or from an external power source. Current The power requirement varies with the number of interfaces used. Typical current consumption: 0.1A at 24V Peak load: 0.25A at 24V Room Conditions Temperature... -
Page 27: Appendix B: Modulations And Power Used
Appendix B: Modulations and Power Used Radio devices operating on the below frequencies should not be installed next to each other. Wireless Transmitter Specifications VBAT = 3.6V Ambient temperature = 25 ° Output power @module RF antenna port Target Power that Meets Spectrum Mask and EVM Compliance Table C.1: Wireless Power Specifications 2.4 GH z TX Power Specifications IEEE... - Page 28 12 Clintonville Rd 140 Waterside Rd Northford, CT 06472 Leicester LE5 1TN, UK (203) 484-7161 +44 (0) 203 4091779 ©2020 Honeywell International Inc.