Advertisement
Available languages
Available languages
EnGLIsh
screw
20
and place it into the bracket screw hole
the corner bracket
38
in Fig. C.
12. On left and right sides, thread a M6 nylon washer
the M6x35 round head screw
supplied 4 mm hex key
tighten the left and right side factory installed screws
located on the corner brackets above the previously installed
screws using the 4 mm hex key
13. Collect the following hardware components, four M6x35
round head screws
20
four M6 lock nuts
23
.You will also need one horizontal
stabilizer bar
5
.
14. In this order, install a M6 open lock washer
flat washer
24
onto each M6x35 round head screw
15. Place a horizontal stabilizer bar
support arms
35
and
16. Align the screw holes
40
support arms
35
and
36
17. Install two screws for each side, into the screw holes
thread them into the horizontal stabilizer bar
in Fig. D.
18. Use the supplied 4mm hex key
M6x35 round head screws
nOTE: Do not fully tighten these screws. You will need
them to be somewhat loose for the composter barrel
installation later.
Installing the Handle and Rotation Lock (Fig. E–G)
nOTE: The handle
6
can be installed on the left side support
arm for left-handed operation.
1. Collect the following components:
and two
27
.
2. Install the handle
6
into the right side support leg
the crank handle
41
faces outward and the gear
inward as shown in Fig. E.
3. Locate the two screw holes
and secure the handle using the two M4x15 self tapping
screws
28
as shown in Fig. E.
4. Tighten the M4x15 self tapping screws
screwdriver (not supplied).
5. To install the handle onto the left side support leg
remove the end cap
43
leg
36
and install it on the right side support leg
shown in Fig. F. Then follow the above steps to install the
handle on the left side, ensuring that the handle crank
faces outward and the gear
6. Install the rotation lock
the handle
6
as shown in Fig. G.
7. Locate the screw hole
8. Place the rotation lock
in Fig. G.
9. Place a M6 nylon washer
lock
7
and the support leg as shown in Fig. G.
10. Insert a M6x55 round head screw
and the screw hole
44
22
for left and right sides as shown
27
20
and then tighten using the
30
and 10 mm wrench
29
30
and 10 mm wrench
, four M6 flat washers
24
26
and a M6
5
between the side
36
.
in the side supports
3
and
, and horizontal stabilizer bar
5
as shown
30
loosely tighten each
20
.
6
,
7
,
21
,
23
, two
43
on the support leg
28
with a cross head
on the top of the left side support
42
faces inwards.
7
on the same side support leg as
44
on the support leg
35
7
onto the support leg as shown
27
inbetween the the rotation
through the assembly
21
.
37
in
11. Thread a M6 lock nut
M6x55 round head screw
tighten using the supplied 4 mm hex key
wrench
onto
when rotated up or down, but not so tight that it prevents
rotational movement. DO nOT OVER TIGhTEn.
. Also
39
Assembling the Composter Barrel (Fig. H–U)
1. Lay out the following components that are required for the
29
.
base assembly:
2. Collect the following components:
and
3. On the underside of each barrel panel is an "a" and a "B".
These will be used to ensure correct panel alignment.
4. Place the the logo panel
on their short sides with the a's matched as shown in Fig. H.
20
.
5. Align the logo panel
tabs
45
Starting from the "a" side of the panels, insert one M5
4
, side
threaded rod
5
6. Ensure the rod tab
40
and
shown in Fig. J.
nOTE: Insert M5 threaded rod
orientation for all panels.
7. Collect the following components:
8. Match the "a" side of the air vent panel
of plain panel
hinge
46
M5 threaded rod
47
is nested in hinge channel
9. Collect and assemble the remaining plain panels
instructed above. Starting from the "a" side of the panels,
insert one M5 threaded rod
28
,
shown in Fig. L. Ensure the rod tab
channel
35
so
10. Collect the following components:
42
faces
11. Install one side of the door base panel
panel
9
35
M5 threaded rod
Ensure the rod tab
12. Collect the following components:
13. Install the chamber divider
36
,
composter barrel
with the divider groove
35
as
nOTE: Ensure the chamber divider
the divider groove
41
14. Starting from the "a" side of the door base panel
the last M5 threaded rod
Fig. P. Ensure the rod tab
15. Collect the following components: two
or
36
.
and eight
16. Install a side cover
barrel
50
eight M5 threaded rods
17. Place a M5 flat washer
threaded rods
nut
18
shown in Fig. R and temporarily tighten them by hand.
23
onto the
21
as shown in Fig. G and
29
until the rotation lock securely stays in place
9
,
10
,
3
,
4
and
10
as shown and a plain panel
10
and a plain panel
interlock and form a hinge
17
through the hinge.
is nested in hinge channel
47
17
9
so the panel tabs
45
. Starting from the "a" side of the panels, insert one
17
through the hinge. Ensure the rod tab
48
as shown in Fig. K.
17
through the hinge as
48
.
Starting from the "a" side of the panels, insert one
17
through the hinge as shown in Fig. M.
47
is nested in hinge channel
into the center of the
12
50
and align the chamber divider
49
as shown in Fig. N.
49
as shown in Fig. O.
17
through the hinge as shown in
47
is nested in hinge channel
19
.
14
onto the "a" side of the composter
. Align the eight side cover holes
17
in the panels as shown in Fig. Q.
19
onto each of the eight M5
17
in the panels. Then thread a M5 hooded
onto each of the eight M5 threaded rods
30
and 10 mm
5
.
9
,
10
, and
17
.
9
9
so the panel
46
as shown in Fig. I.
as
48
with rod tab
47
in this
, and
.
11
17
11
with the "a" side
interlock and form a
9
as
47
is nested in hinge
13
, and
17
.
13
, onto a plain
48
.
12
, and
17
.
12
12
is fully seated into
13
, insert
48
.
14
, eight
18
,
51
with the
17
as
Advertisement
