Black & Decker BEPW1300L Original Instructions Manual page 11

On vertical surfaces, apply the detergent starting at the bottom
and work your way upward. This will prevent the detergent
from sliding down and causing streaks. High pressure
rinsing should also progress from the bottom to top. On
particularly tough stains, it may be necessary to use a brush in
combination with detergents and high pressure rinsing.
Moving the Pressure Washer
1. Turn OFF the pressure washer unit ( 16 ) by rotating the
ON/OFF dial ( 17 ) to the OFF position and then turn OFF
the water supply.
2. Point the spray wand ( 2 ) in a safe direction and pull the
trigger ( 7 ) to release remaining water pressure.
3. When the spray wand is completely empty, lift the
pressure washer by the handle ( 18 ).
Shutdown
1. Turn OFF the pressure washer unit ( 16 ) by rotating the
ON/OFF dial ( 17 ) to the OFF position and unplug the
cord from the outlet.
2. Turn OFF water at the faucet or disconnect from any other
water source.
3. Discharge residual pressure by squeezing the trigger ( 7 )
until no more water comes out of the spray wand ( 2 ).
4. Engage the spray trigger lock‑off ( 6 ).
5. Disconnect the garden hose ( 28 ) from the water
intake ( 25 ).
6. Disconnect the high pressure hose ( 1 ) from the high
pressure water outlet ( 20 ) and drain hose.
Self Priming
1. Connect the inlet hose to the pressure washer.
Refer to Attaching Garden Hose under Assembly
and Adjustments.
2. Place the free end of the hose with filter attached into the
alternative water source (e.g. bucket, etc.)
3. Connect the high pressure hose to the spray handle.
Please refer to Attaching High Pressure Hose under
Assembly and Adjustments.
4. Plug the pressure washer unit into a power source.
5. Actuate the pressure washer by rotating the ON/OFF dial
to the ON position.
6. Turn OFF the pressure washer as soon as water is
spraying out of the outlet tube of the unit.
7. Unplug the pressure washer unit from the power source.
8. Assemble the high pressure hose to the outlet tube of
the pump.
9. Plug the pressure washer unit into a power source.
10. Actuate the pressure washer by rotating the ON/OFF dial
to the ON position.
11. Actuate the trigger of the spray handle to start
cleaning work.
(Original instructions)
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
@
care and regular cleaning.
Warning! Before performing any maintenance on
the tool.
Š Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Š Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent‑based cleaner.
Cleaning
Nozzle Cleaning (Fig. A, G)
If the nozzle becomes clogged with foreign materials, such as
dirt, excessive pressure may develop. If the nozzle becomes
partially clogged or restricted, the pump pressure will pulsate.
Clean the nozzle immediately using the nozzle cleaner.
1. Turn OFF and unplug the pressure washer unit ( 16 ).
2. Turn OFF the water supply.
3. Pull trigger ( 7 ) on spray handle ( 4 ) to relieve any
water pressure.
4. Remove the nozzle from the spray wand ( 2 ) by
depressing the button ( 3 ).
5. Using the nozzle cleaning tool ( 14 ), unclog any debris
from the nozzle.
6. Run water from a faucet or garden hose through
the nozzle.
Filter Cleaning (Fig. K)
Inspect the filter ( 10) before each use and clean if necessary.
Remove the filter element and run under clear water to
remove any debris.
Storage
• Store in a dry, covered location above freezing
temperature. STORE INDOORS.
• Always completely empty water from high pressure hose,
pressure washer unit, nozzles, and spray wand.
• Nozzles can be stored in the unit as shown in Fig. H.
NOTE: The turbo (BEPW2000) or pen to fan nozzles can
be stored on the wand.
• Power cord can be stored coiled up and secured with the
cord retaining hook ( 21 ) as shown in Fig. I.
• High pressure hose ( 1 ) can be stored coiled up and
secured on the handle ( 18 ) with the help of the hook and
latch strap ( 27 ) as shown in Fig. I.
• The spray handle ( 4 ) can be stored onto the rear of the
unit using the bracket ( 26 ) as shown in Fig. I.
• The spray wand ( 2 ) can be stored onto the rear of the
unit using the bracket ( 26 ) as shown in Fig. I.
ENGLISH
11