Makita VC009G Instruction Manual page 19

1. Shoulder the vacuum cleaner body and fas-
ten lower and upper belts. Adjust the tightness as
necessary.
► Fig.31
2.
Press button to start vacuuming. If you want
to change the suction power, press
desired suction power is selected. Press
stop.
► Fig.32
During the operation, hook the switch box on the lower
belt or the D-ring.
► Fig.33
3. Replace the filter bag when it becomes full. Open
the lid and take out the filter bag. Pull the strip on the
side of the opening to shut the filter bag and dispose of
the filter bag in whole.
► Fig.34: 1. Strip
When using a dust bag, take out the dust bag and dis-
pose of the dust by releasing the latch.
► Fig.35: 1. Latch
NOTICE:
Periodically check the filter bag if it is
full. Continuous use with the filter bag full results in
reduced suction power.
NOTICE:
Do not use an used filter bag. The filter
bag is designed for single use. Using filter bag repeat-
edly may cause clogging of the filter and results in
damage to the cleaner. If you want to use the bag
repeatedly, use a dust bag.
WIRELESS ACTIVATION
FUNCTION
What you can do with the wireless
activation function
The wireless activation function enables clean and
comfortable operation. By connecting a supported tool
to the cleaner, you can run the cleaner automatically
along with the switch operation of the tool.
► Fig.36
NOTICE:
Be sure to refer to the instruction man-
ual of the tool when using the cleaner with wire-
less activation function.
NOTICE:
Do not disassemble or tamper with the
wireless unit.
NOTICE:
To prevent dust coming into the slot
of the wireless unit, always close the lid securely
during operation and storage.
NOTICE:
Do not remove the wireless unit while
the power is being supplied. Doing so may cause a
malfunction of the wireless unit.
NOTICE:
Do not press the wireless activation
button too hard and/or press the button with an
object with a sharp edge.
NOTE: Wireless activation needs Makita tools
equipped with the wireless unit.
NOTE: Prior to the initial use of the wireless activa-
tion function with each tool, the tool registration is
required. Once the registration is finished with the
tool, the re-registration is not required unless it is
button until the
cancelled.
button to
NOTE: Before registration, be sure that the wireless
unit is properly inserted.
NOTE: One wireless unit can register up to 10 links
with other wireless units. If more than 10 other wire-
less units are registered to one wireless unit, the one
registered earliest will be cancelled automatically.
NOTE: The position of the wireless activation button
varies depending on the tool.
NOTE: The cleaner also starts by pressing
when the stand-by switch is set to " I (ON)".
However the
less activation function is used.
Installing the wireless unit
stable surface when installing the wireless unit.
NOTICE:
before installing the wireless unit. Dust or dirt
may cause malfunction if it comes into the slot of the
wireless unit.
NOTICE:
static, touch a static discharging material, such
as a metallic part, before picking up the wireless
unit.
NOTICE:
always be sure that the wireless unit is inserted
in the correct direction and the lid is completely
closed.
1.
► Fig.37: 1. Lid
2.
the lid.
When inserting the wireless unit, align the projections
with the recessed portions on the slot.
► Fig.38: 1. Wireless unit 2. Projection 3. Lid
When removing the wireless unit, open the lid slowly.
The hooks on the back of the lid will lift the wireless unit
as you pull up the lid.
► Fig.39: 1. Wireless unit 2. Hook 3. Lid
After removing the wireless unit, keep it in the supplied
case or a static-free container.
NOTICE:
the lid when removing the wireless unit. If the
hooks do not catch the wireless unit, close the lid
completely and open it slowly again.
19 ENGLISH
button will not work when the wire-
CAUTION:
Place the cleaner on a flat and
Clean the dust and dirt on the cleaner
To prevent the malfunction caused by
When installing the wireless unit,
Open the lid on the cleaner as shown in the figure.
Insert the wireless unit to the slot and then close
4. Recessed portion
Always use the hooks on the back of
button