Cisco NCS 1004 Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Control Unit
  5. NCS 1004
  6. Manual

Cisco NCS 1004 Manual

Hide thumbs Also See for NCS 1004:
Table of Contents

Advertisement

Quick Links

Download this manual
Install Cisco NCS 1004 Modules
This chapter contains procedures to install the modules of Cisco NCS 1004.
Caution
All the modular slots in the NCS 1004 chassis should always be populated with respective modules (line-cards,
controller, PSU & fan units). Empty line card slots to be populated with filler modules, which are shipped
with the chassis. The replacement or upgrade of the modules (Online Insertion or Removal, OIR) to be
performed only when the ambient temperature is below 30-degree C. The OIR of modules should be completed
within five minutes to prevent overheating of the components.
•
•
About Line Cards, on page 3
•
•
Install Fan Unit, on page 14
•
•
•
•
Install Pluggables, on page 18
•
Air Filter, on page 23
Install Cisco NCS 1004 Modules
1

Advertisement

Table of Contents
loading

Related Manuals for Cisco NCS 1004

Summary of Contents for Cisco NCS 1004

  • Page 1: Table Of Contents

    This chapter contains procedures to install the modules of Cisco NCS 1004. Caution All the modular slots in the NCS 1004 chassis should always be populated with respective modules (line-cards, controller, PSU & fan units). Empty line card slots to be populated with filler modules, which are shipped with the chassis.

  • Page 2: Supported Controller Cards

    The card supports a default of 9600 baud rate on the RS232 console port and runs on BIOS version 5.10. The Cisco NCS 1004 supports the following controller cards: • NCS1K4-CNTLR-K9 The NCS1K4-CNTLR-K9 controller card supports a default of 115200 baud rate on the RS232 console port and runs on BIOS version 4.20.

  • Page 3: About Line Cards

    Using a T15 Torx screwdriver, tighten the two M3 T15 torx screws to a torque value of 0.65 N-m. About Line Cards The Cisco NCS 1004 supports the following line cards: • 1.2T DWDM Line Card • 1.2TL DWDM Line Card •...
  • Page 4 Install Cisco NCS 1004 Modules 1.2TL Line Card The physical characteristics of the 1.2T line card are: • Height—40.4 mm • Breadth—191.9 mm • Depth—277 mm without the fiber management bracket; 297.97 mm with the fiber management bracket • Weight—3.2 kg...
  • Page 5 Install Cisco NCS 1004 Modules OTN-XP Line Card For the LED details of the line card, see the Line Card LEDs section. OTN-XP Line Card The OTN-XP line card supports up to 1.6Tbps of OTN aggregation switching functionality to optimize the available bandwidth.
  • Page 6 Install Cisco NCS 1004 Modules QXP-K9 Line Card QXP-K9 Line Card Table 3: Feature History Feature Name Release Information Description NCS1K4-QXP-K9 Line Card Cisco IOS XR Release 7.7.1 NCS1K4-QXP-K9 line card delivers low cost 100G and 400G DWDM transmission with ZR+ optics on a router.
  • Page 7 Install Line Card This task has details about installing a line card in to the NCS 1004 chassis. The chassis is shipped with filler cards and/or line cards. The Cisco NCS 1004 chassis supports a maximum of four line cards.
  • Page 8 Install Cisco NCS 1004 Modules Install Line Card Figure 2: Installing the OTN-XP Line Card Install Cisco NCS 1004 Modules...

  • Page 9: Install Power Supply

    Using the Torx screwdriver, tighten the two M3, T15 Torx screws of the line card, to a torque value of 0.65 N-m. Install Power Supply This task has information about installing the PSUs into the NCS 1004 chassis. Step 1 Orient the PSU correctly before inserting.
  • Page 10 Connect DC Power to NCS 1004 Caution NCS 1004 relies on the protective devices in the building installation to protect against short circuit, overcurrent, and ground faults. Ensure that the protective devices comply with local and national electrical codes. Figure 5: Rating Label for DC Power Step 1 Verify that the correct fuse panel is installed in the top mounting space.
  • Page 11 Install Cisco NCS 1004 Modules Connect DC Power to NCS 1004 Step 3 Dress the power according to local practice. Step 4 Connect the office battery and return cables according to the fuse panel engineering specifications. Step 5 Affix the power lug on the unit with two screws. Tighten the screws using a torque of 2.7 Nm +/- 0.3 Nm.
  • Page 12 Connect AC Power to NCS 1004 Caution NCS 1004 relies on the protective devices in the building installation to protect against short circuit, overcurrent, and ground faults. Ensure that the protective devices comply with local and national electrical codes. Figure 7: Rating Label for AC Power The voltage rating value for AC power ranges either between 200 V to 240 V or between 100 V to 127 V depending on the standards in various countries.
  • Page 13 Install Cisco NCS 1004 Modules Connect AC Power to NCS 1004 Figure 8: Connecting 90-degree Power Cable 90-degree exit cables 180-degree ground lug Figure 9: Connecting Straight Power Cable Straight exit cables 90-degree ground lug Install Cisco NCS 1004 Modules...

  • Page 14: Install Fan Unit

    Install Cisco NCS 1004 Modules Install Fan Unit Install Fan Unit This task has information about installing the fan units into the chassis. Step 1 Orient the fan unit correctly before inserting. Check for the This Side Up label. Step 2 Holding the handle with one hand and supporting the fan unit with the other hand, insert the fan unit in to the slot on the rear side of the chassis.

  • Page 15: Attach Fiber Management Bracket

    Install Cisco NCS 1004 Modules Attach Fiber Management Bracket Figure 11: Spring-loaded Lever in Released Condition Sping-loaded lever Attach Fiber Management Bracket This task has details about attaching a fiber management bracket to a line card or filler card. Step 1 Fix the fiber management bracket to the card (line card or filler card, as the case may be).

  • Page 16: Adjust Fiber Management Bracket Of The 1.2T, 1.2Tl, 2-Qdd-C, And Qxp-K9 Line Cards

    Install Cisco NCS 1004 Modules Adjust Fiber Management Bracket of the 1.2T, 1.2TL, 2-QDD-C, and QXP-K9 Line Cards Adjust Fiber Management Bracket of the 1.2T, 1.2TL, 2-QDD-C, and QXP-K9 Line Cards This task has details about how to adjust the length of the fiber management bracket.

  • Page 17: Adjust Fiber Management Bracket Of The Otn-Xp Line Card

    Install Cisco NCS 1004 Modules Adjust Fiber Management Bracket of the OTN-XP Line Card • If no one groove is visible, the bar is in transient stage. • If one grove is visible, the bar is correctly installed and locked.

  • Page 18: Install Pluggables

    Install Cisco NCS 1004 Modules Install Pluggables Figure 14: Fiber Management Bracket Set Fiber management bracket Install Pluggables This task has information about installing the pluggables on a line card. The line card is shipped with dust caps. Caution Protect the line card by inserting dust caps into the pluggable slots when no pluggable is inserted.
  • Page 19 Install Cisco NCS 1004 Modules Install Pluggables Figure 15: Inserting QSFP Pluggable (1.2T Line Card) Figure 16: Inserting QSFP-DD Pluggable (OTN-XP Line Card) Install Cisco NCS 1004 Modules...
  • Page 20 Install Cisco NCS 1004 Modules Install Pluggables The pull tabs of the pluggables must always face down for top rows; the pull tabs of the pluggables must always Caution face up for bottom rows. Figure 17: Inserting QSFP-28 Pluggable (OTN-XP Line Card) Do not forcibly push the pluggable into the slot, this might damage the pluggable and/or the slot.
  • Page 21 Install Cisco NCS 1004 Modules Install Pluggables Figure 19: Using the Push Tool to Push the Pluggables Step 3 Route the cables emerging from the pluggables using the fiber management bracket as shown in the following figure. Figure 20: Fiber Management Bracket with fibers from Pluggables (1.2T, 1.2TL, 2-QDD-C, and QXP-K9 Line Cards)
  • Page 22 Install Cisco NCS 1004 Modules Install Pluggables Figure 21: Fiber Management Bracket for the OTN-XP Line Card Fibers from pluggables resting on the cable support bracket Guidelines for managing the fibers and cables: • Use velcro tapes to tie the fibers to the fiber management bracket.

  • Page 23: Air Filter

    Failure to replace a compromised air filter can result in insufficient air circulation through the chassis and temperature-related environmental alarms. The Cisco NCS 1004 air filter has the following components: • Two air filter side brackets •...
  • Page 24 Install Cisco NCS 1004 Modules Install Air Filter In case the air filter is being installed after the chassis installation is completed, then unscrew and remove the Note four screws (on either side) that bind the chassis to the rack. After fixing the air filter side brackets, only three screws are used on either side, to bind the chassis and air filter side brackets to the rack.
  • Page 25 Install Cisco NCS 1004 Modules Install Air Filter Figure 23: Installing the Air Filter Step 2 Slide the air filter frame in to the air filter side brackets. Step 3 Using a T15 Torx screwdriver, tighten the screw on either side (placed diagonally) to a torque value of 0.65 N-m.
  • Page 26 Install Cisco NCS 1004 Modules Install Air Filter Install Cisco NCS 1004 Modules...

Table of Contents