Table of Contents
Advertisement
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
Battery tool use and care
24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
25. Use
power
tools
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
26. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal
to
another. Shorting the battery
terminals together may cause burns or a fire.
27. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may
cause irritation or burns.
Service
28. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
29. Follow
instruction
changing accessories.
30. Keep handles dry, clean and free from oil and
grease.
CORDLESS MITER SAW SAFETY
WARNINGS
1.
Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still
cause severe injury.
2.
Check the saw blade carefully for cracks or
deformation before operation.
Replace damaged blades immediately.
3.
Replace the kerf board when worn.
4.
Use only saw blades specified by the
manufacturer which conform to EN847-1.
5.
Do not use saw blades manufactured from
high speed steel.
6.
Wear eye protection.
only
with
specifically
for
lubricating
and
ENB118-4
7.
Wear hearing protection to reduce the risk of
hearing loss.
8.
Wear gloves for handling saw blade (saw
blades shall be carried in a holder wherever
practicable) and rough material.
9.
Connect miter saws to a dust collecting device
when sawing.
10. Select saw blades in relation to the material to
be cut.
11.
Do not use the saw to cut other than wood.
12. Always secure all moving portions before carrying
the tool. When lifting or carrying the tool, do not
use the guard as a carrying handle.
13.
Do not operate saw without guards in place. Check
blade guard for proper closing before each use. Do
not operate saw if blade guard does not move freely
and close instantly. Never clamp or tie the blade
guard into the open position.
14. Keep the floor area free of loose material e.g.
chips and cut-offs.
15. Use only saw blades that are marked with a
maximum speed equal to or higher than the no
load speed marked on the tool.
16. When the tool is fitted with a laser or LED, do
not replace the laser or LED with a different
type. Ask an authorized service center for repair.
17. Never remove any cut-offs or other parts of the
workpiece from the cutting area whilst the tool
is running with an unguarded saw blade.
18. Do not perform any operation freehand. The
workpiece must be secured firmly against the turn base
and guide fence with the vise during all operations.
Never use your hand to secure the workpiece.
19. Ensure that the tool is stable before each cut.
20. Fix the tool to a work bench, if needed.
21. Support long workpieces with appropriate
additional supports.
22. Never cut so small workpiece which cannot be
securely held by the vise. Improperly held
workpiece may cause kickback and serious
personal injury.
23. Never reach around saw blade.
24. Turn off tool and wait for saw blade to stop
before
moving
settings.
25. Unplug
tool
servicing.
26. Stopper pin which locks the cutter head down
is for carrying and storage purposes only and
not for any cutting operations.
27. Do not use the tool in the presence of
flammable liquids or gases. The electrical
operation of the tool could create an explosion and
fire when exposed to flammable liquids or gases.
28. Use only flanges specified for this tool.
4
workpiece
or
before
changing
blade
changing
or
Advertisement
Table of Contents
