Black & Decker BCD900 Manual page 9

@
WARNING! Before drilling into walls, floors or
@
ceilings, check for the location of wiring and pipes.
WARNING! Do not apply chisels when the tool is in
the drilling mode.
Forward/reverse action (fig. I)
Move the selector (2) to indicate the direction you require.
u
Switching on and off (fig. I)
To switch the tool on, press the variable speed switch (1).
u
The tool speed depends on how far you press the switch.
As a general rule, use low speeds for large diameter drill
u
bits and high speeds for smaller diameter drill bits.
To switch the tool off, release the variable speed switch.
u
Selecting the operating mode (fig. J)
The tool can be used in three operating modes.
To operate the operating mode selector (3), push the
u
unlock button (20) and rotate the selector towards the
required position, as indicated by the symbols.
Drilling
For drilling in steel, wood and plastics, and for
u
screwdriving set the operating mode selector (3) to the
position (19).
Hammer drilling
For hammer drilling in masonry and concrete, set the
u
operating mode selector (3) to the
When hammering, the tool should not bounce and run
smoothly. If necessary, increase the speed.
Hammering
For hammering with spindle lock, and for light chiselling
u
q
and chipping, set the operating mode selector (3) to the
position (21).
When changing from hammer drilling to chiselling, turn the
u
chisel to the desired position. If resistance is felt during mode
change, slightly turn the chisel to engage the spindle lock.
Accessories
The performance of your tool depends on the accessory used.
Stanley BLACK+DECKER accessories are engineered to high
quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
r
qr
position (18).
(Original instructions)
Warning! Before performing any maintenance on corded /
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new plug.
@
u
Connect the blue lead to the neutral terminal.
u
WARNING! No connection is to be made to the earth
terminal. Follow the fitting instructions supplied with
good quality plugs. Recommended fuse: 5 A.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recovered or
recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according to local
provisions. Further information is available at www.2helpU.com
Technical data
BCD900D1S / D1K BCD900E2K BCD900M1K
Input voltage
V 18
DC
No-load speed min 0 - 1800
-1
Impact rate min 0 - 6350
-1
Weight kg 2.60
Max. drilling capacity
Concrete mm 18
Steel
mm 13
Wood
mm 25
Battery
BL2018
Voltage V 18
DC
Capacity Ah 2.0
type Li-Ion
ENGLISH
BCD900B
18 18 18
0 - 1800 0 - 1800 0 - 1800
0 - 6350 0 - 6350 0 - 6350
2.60 2.87 2.22
18 18 18
13 13 13
25 25 25
BL2518 BL4018 Not Supplied
18 18
2.5 4.0
Li-Ion Li-Ion
9