Makita DFT041R Instruction Manual page 9

For LED#B
► Fig.7: 1. LED#B1 2. LED#B2
LED indicator / Beeper on the tool shows the following functions.
Description Viewed color
LED#B Green
LED#B Red
Note 1: Refer to a instruction manual of receiver (accessory) RCV02 when connecting it.
Note 2: Communication distance: 10 m or less (variable up to 10 m depending on the operation environment)
CAUTION:
• Make sure that LED#B2 does not light up before removing a battery cartridge from the tool. If a battery car-
tridge is removed while LED#B2 lights up or blinks, tools stored data will be deleted.
Adjusting the fastening torque
► Fig.8: 1. Adjust grip 2. Ring
When you wish to drive machine screws, wood screws,
hex bolts, etc. with the predetermined torque, adjusting
the fastening torque as follows.
1. First remove the battery cartridge from the tool.
2. Loosen and remove the screw that secures ring.
3. Rotate the ring in the front of the tool by hand so
that a hole can be seen below the ring.
4. Place the battery cartridge in place and pull the
switch trigger. Release it so that the adjust ring
rotates and becomes visible in the hole. And then
remove the battery cartridge.
► Fig.9: 1. Adjust ring 2. Ring 3. Scale 4. Adjust grip 5. Hole
for adjust grip 6. Yellow line 7. Compression spring
5. Use an optional adjust grip to adjust the fastening
torque. Insert the pin of the adjust grip into the hole
in the front of the tool. And then, turn the adjust grip
clockwise to set a greater fastening torque, and
counterclockwise to set a smaller fastening torque.
6. Align the yellow line with your desired number on
the fastening torque scale.
7. Insert the battery cartridge and be sure that a fas-
tening torque has been set up by using a fastening
torque tester.
8. Rotate the ring in front of the tool and then tighten
the screw to secure the ring.
NOTE:
• Numbers on the fastening torque scale is a
guideline to set up your desired fastening torque.
1 lights up when the tool is connected to a receiver.
when the tool is on the step of being connected to a
2 blinks
receiver. (Note 1)
one of the status below
3-1 when the battery cartridge is removed from the tool.
when the tool is left idle for more than 15 minutes
3 is turned off 3-2
with a installed battery cartridge.
when the tool is not within the transmission
3-3
distance. (Note 2)
when the tool's stored number of data reaches its
1 lights up
storable number of data.
when the tool's stored number of data is equal to or
2 blinks
smaller than its storable number of data.
when the tool has no stored data to transmit to a
3 is turned off
receiver.
9 ENGLISH
View and status
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
the battery cartridge is removed before carrying
out any work on the tool.
Installing or removing driver bit or
socket bit
► Fig.10
Use only bits that has inserting portion shown in the
figure.
For tool with shallow bit hole: A=12mm, B=9mm
For tool with deep bit hole: A=17mm, B=14mm
To install the bit, pull the sleeve in the direction of the
arrow and insert the bit into the sleeve as far as it will
go. Then release the sleeve to secure the bit.
► Fig.11: 1. Bit 2. Sleeve
To remove the bit, pull the sleeve in the direction of the
arrow and pull the bit out firmly.
NOTE:
• If the bit is not inserted deep enough into the
sleeve, the sleeve will not return to its original
position and the bit will not be secured. In this
case, try re-inserting the bit according to the
instructions above.