Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DDA460Z
Summary of Contents for Makita DDA460Z
- Page 1 INSTRUCTION MANUAL Cordless Angle Drill DDA460 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DDA460 Gear speed High Drilling capacities Steel 13 mm Wood Auger bit: 50 mm Auger bit: 50 mm Self-feed bit: 65 mm Self-feed bit: 118 mm Hole saw: 105 mm Hole saw: 159 mm No load speed 0 - 1400 min 0 - 350 min Overall length 538 mm... -
Page 3: General Power Tool Safety Warnings
Use personal protective equipment. Always SAFETY WARNINGS wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions General power tool safety warnings will reduce personal injuries. Prevent unintentional starting. Ensure the WARNING: switch is in the off-position before connecting Read all safety warnings, instruc- tions, illustrations and specifications provided with this to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with... - Page 4 Disconnect the plug from the power source Service Have your power tool serviced by a qualified and/or remove the battery pack, if detachable, from the power tool before making any adjust- repair person using only identical replacement ments, changing accessories, or storing power parts. This will ensure that the safety of the power tools. Such preventive safety measures reduce tool is maintained.
-
Page 5: Functional Description
To remove the battery cartridge, slide it from the tool SAVE THESE INSTRUCTIONS. while sliding the button on the front of the cartridge. To install the battery cartridge, align the tongue on the CAUTION: Only use genuine Makita batteries. battery cartridge with the groove in the housing and slip Use of non-genuine Makita batteries, or batteries that it into place. Insert it all the way until it locks in place have been altered, may result in the battery bursting with a little click. If you can see the red indicator on the causing fires, personal injury and damage. It will upper side of the button, it is not locked completely. also void the Makita warranty for the Makita tool and charger. CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. - Page 6 Overheat protection Indicating the remaining battery When the tool/battery is overheated, the tool stops capacity automatically. In this situation, let the tool/battery cool before turning the tool on again. Only for battery cartridges with the indicator Overdischarge protection When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery. Main power switch WARNING: Always turn off the main power switch when not in use. To stand by the tool, press the main power button until the main power lamp lights up.
-
Page 7: Speed Change
the switch trigger. Release the switch trigger to stop. This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the NOTE: The tool automatically stops if you keep pull- A side for clockwise rotation or from the B side for coun- ing the switch trigger for about 6 minutes. -
Page 8: Front Handle
Two speed ranges can be preselected with the speed Front handle change knob. To change the speed, depress the lock button and turn Do not fix the front handle beyond CAUTION: the speed change knob so that the pointer points to the position 1 for low speed or the position 2 for high speed. -
Page 9: Operation
Installing or removing drill bit Holding tool To install the drill bit, place it in the chuck as far as it will CAUTION: This is a powerful tool. High torque go. Tighten the chuck by hand. Place the chuck key in is developed and it is important that the tool each of the three holes and tighten clockwise. -
Page 10: Maintenance
There is a tremendous force exerted on be inspected by a Makita Factory or Authorized the tool/drill bit at the time of hole break through. Service Center. -
Page 11: Optional Accessories
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regard- ing these accessories, ask your local Makita Service Center. • Drill bits • Plastic carrying case •... - Page 12 Jan-Baptist Vinkstraat 2, Makita Europe N.V. 3070 Kortenberg, Belgium 3-11-8, Sumiyoshi-cho, Makita Corporation Anjo, Aichi 446-8502 Japan 885635-222 www.makita.com 20171220...