Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DTD171Z
Summary of Contents for Makita DTD171Z
- Page 1 INSTRUCTION MANUAL Cordless Impact Driver DTD171 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DTD171 Fastening capacities Machine screw 4 mm - 8 mm Standard bolt 5 mm - 16 mm High tensile bolt 5 mm - 14 mm No load speed Max impact mode 0 - 3,600 min Hard impact mode 0 - 3,200 min Medium impact mode 0 - 2,100 min... -
Page 3: Safety Warnings
Save all warnings and instruc- Intended use tions for future reference. The tool is intended for screw driving in wood, metal The term "power tool" in the warnings refers to your and plastic. mains-operated (corded) power tool or battery-operated (cordless) power tool. Noise Work area safety The typical A-weighted noise level determined accord- Keep work area clean and well lit. Cluttered or ing to EN62841-2-2: dark areas invite accidents. - Page 4 Remove any adjusting key or wrench before Maintain power tools and accessories. Check for turning the power tool on. A wrench or a key left misalignment or binding of moving parts, break- attached to a rotating part of the power tool may age of parts and any other condition that may result in personal injury. affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents Do not overreach.
- Page 5 CAUTION: Only use genuine Makita batteries. product. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting MISUSE or failure to follow the safety rules stated causing fires, personal injury and damage. It will in this instruction manual may cause serious also void the Makita warranty for the Makita tool and personal injury.
-
Page 6: Functional Description
Overheat protection FUNCTIONAL DESCRIPTION When the tool/battery is overheated, the tool stops automatically. In this situation, let the tool/battery cool CAUTION: Always be sure that the tool is before turning the tool on again. switched off and the battery cartridge is removed Overdischarge protection before adjusting or checking function on the tool. When the battery capacity is not enough, the tool stops Installing or removing battery cartridge automatically. In this case, remove the battery from the tool and charge the battery. - Page 7 Switch action ► 1 . Button Pull the switch trigger to turn on the lamp. To turn off, ► 1 . Switch trigger release it. The lamp goes out approximately 10 seconds after releasing the switch trigger. CAUTION: Before installing the battery car- To keep the lamp off, turn off the lamp status. To turn off tridge into the tool, always check to see that the the lamp status, first pull and release the switch trigger.
- Page 8 Quick mode-switching button This tool has a reversing switch to change the direction of rota- tion. Depress the reversing switch lever from the A side for clock- The function of the quick mode-switching button varies wise rotation or from the B side for counterclockwise rotation. depending on whether you have registered the applica- When the reversing switch lever is in the neutral posi- tion mode to the tool.
- Page 9 Quick reference The following table shows the functions of the quick mode-switching button. indicates the quick mode-switching button. Button(s) / Purpose How to confirm Registering the application The customize lamp and the mode lamp of desired application mode blinks. (When quick mode-switch- ing function is OFF) The lamps on the tool flash Changing the impact force once. by the quick mode-switch- ing button (When quick mode-switch-...
- Page 10 Changing the impact force You can change the impact force in four steps: max, hard, medium, and soft. This allows a tightening suitable to the work. The level of impact force changes every time you press the button or the quick mode-switching button. You can change the impact force within approximately one minute after releasing the switch trigger or press- ing the button , or the quick mode-switching button.
- Page 11 Changing assist type This tool employs assist function that offers several easy-to-use application modes for driving screws with good control. The type of the application mode changes every time you press the button You can change the assist type within approximately one minute after releasing the switch trigger or press- ing the button , or the quick mode-switching button. ► 1 . Button Application mode Maximum blows Feature Purpose (Assist type displayed on panel) Wood mode *1 3,800 min (/min) This mode helps to prevent a screw from falling at...
- Page 12 Quick mode-switching function Using the quick mode-switching function When the tool is in the mode that is not registered, What you can do with the quick mode- press the quick mode-switching button to switch to the switching function registered application mode. The tool switches between the registered application mode and last application The quick mode-switching function saves the time for changing mode every time you press the quick mode-switching the application mode of the tool. You can switch to your desired...
-
Page 13: Operation
Procedure 1 Installing hook For tool without one-touch type sleeve CAUTION: When installing the hook, always secure it with the screw firmly. If not, the hook may come off from the tool and result in the personal injury. ► 1 . Driver bit 2. Sleeve To install the driver bit, pull the sleeve in the direction of the arrow and insert the driver bit into the sleeve as far as it will go. -
Page 14: Maintenance
To maintain product SAFETY and RELIABILITY, NOTICE: If you use a spare battery to continue repairs, any other maintenance or adjustment should the operation, rest the tool at least 15 min. be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 14 ENGLISH... -
Page 15: Optional Accessories
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regard- ing these accessories, ask your local Makita Service Center. • Driver bits • Socket bits •... - Page 16 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885673-224 www.makita.com 20180620...