Download
Share
Print this page
Draytek VigorAP 920C Quick Start Manual
  1. Manuals
  2. Brands
  3. Draytek Manuals
  4. Wireless Access Point
  5. VigorAP 920C
  6. Quick start manual

Draytek VigorAP 920C Quick Start Manual

802.11ac ceiling-mount ap
Hide thumbs

Advertisement

Quick Links

Download this manual
i

Advertisement

loading

Related Manuals for Draytek VigorAP 920C

Summary of Contents for Draytek VigorAP 920C

  • Page 2 VigorAP 920C/1000C 802.11ac Ceiling-mount AP Quick Start Guide Version: 1.1 Firmware Version: V1.3.2 (For future update, please visit DrayTek web site) Date: July 6, 2020...
  • Page 3 This DrayTek product uses software partially or completely licensed under the terms of the GNU GENERAL PUBLIC LICENSE. The author of the software does not provide any warranty. A Limited Warranty is offered on DrayTek products. This Limited Warranty does not cover any software applications or programs.
  • Page 4 Declaration of Conformity Hereby, DrayTek Corporation declares that the radio equipment type VigorAP 920C/ VigorAP 1000C is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: http://www.draytek.com.tw/ftp/VigorAP 920/Document/CE/ Manufacturer: DrayTek Corp.
  • Page 5 88.6% 88.2% efficiency Efficiency at low load 73.6% 78.0% 81.3% 83.3% 83.7% 74.5% 80.5% 86.4% 85.4% No-load power 0.07W 0.07W 0.07W 0.07W 0.07W 0.07W 0.10W 0.07W 0.10W consumption External power supply (Power Adapter) information. For more update, please visit www.draytek.com.

  • Page 6: Table Of Contents

    1. Package Content ....................1 2. Panel Explanation....................2 3. Mounting the Access Point.................. 4 4. Software Configuration ..................8 5. Customer Service ....................12...

  • Page 7: Package Content

    Please inspect the package contents. If anything is missing or damaged, please contact DrayTek or your dealer immediately. Vigor Device Quick Start Guide Ethernet Cable Mounting Bracket The type of the power adapter depends on the country that the device will be installed.

  • Page 8: Panel Explanation

    920C 1000C Status Explanation A USB device is connected and active. Blinking The data is transmitting. 5G / 2.4G Wireless function is ready. /5G-1 / 5G-2 Wireless function is not ready. Blinking Data is being transmitted (sending/receiving). P2 / P1(PoE) The LAN port is connected.
  • Page 9 Interface Description Restore the default settings. Usage: Switch on the access point. Press and hold reset button for at least 5 seconds. VigorAP will restart with the factory default configuration. P2/P1(PoE) Connectors for local networked devices. A connector for a USB device. A security hole for installing the anti-theft lock.

  • Page 10: Mounting The Access Point

    This section will guide you through installing the VigorAP. Note For the sake of personal safety, only trained and qualified personnel should install this access point. VigorAP can be mounted on the board of calcium silicate. Below shows an exploded view of VigorAP installation.
  • Page 11 Follow the steps listed below to mount the access point. Place the bracket on the front side of the calcium silicate board and fasten it with four screws. When the bracket is in place, reverse the board. Put the washer on the screw.
  • Page 12 Insert the cap nut to the screw on the washer. Rotate the cap nut until it locks firmly on the washer.
  • Page 13 There are four latches on the bracket. Put the device (VigorAP) on the bracket with the direction shown below. Note To remove the AP, please A. Insert a small-sized flathead screwdriver to the locking notch. B. Push to separate the device from the four latches.

  • Page 14: Software Configuration

    This section will guide you through the configuration of the settings using a web browser. Here we take VigorAP 1000C as an example. Make sure your PC is connected to access point correctly. Open a web browser on your PC and type http://192.168.1.2. A pop-up window will open asking you for a username and password.
  • Page 15  Install VigorAP on the place you want.  As a mesh node, settings related to this VigorAP must be configured by a remote Mesh Root within the mesh network. The user must detect this VigorAP via a Mesh Root to add it as a mesh node. As an access point, VigorAP must be connected to a router and configured in AP (Access Point) / Range Extender mode.
  • Page 16  There are two methods to configure VigorAP. Method 1: (a) First, open a web browser on your PC and type https://192.168.1.2. A pop-up window will open to ask for username and password. (b) After clicking Login, Quick Start Wizard for configuring wireless settings will appear as follows.
  • Page 17 Method 2: (a) Use a mobile phone to scan the QR code named with DrayTek Wireless App to download DrayTek Wireless APP. (b) After downloading, run the APP. (c) Click Quick Start Wizard. Next, scan the QR code named with Connect SSID.

  • Page 18: Customer Service

    Web registration is preferred. You can register your Vigor device via http://www.draytek.com. & & Due to the continuous evolution of DrayTek technology, all devices will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents. http://www.draytek.com...

This manual is also suitable for:

Vigorap 1000c