Advertisement
high capacity 1 in. BSPP by 1 in. BSPP gas control.
THERMOCOUPLE REQUIRED (ordered separately) for
24V, 100V, 120V, and 2201240V models: Q309 orQ340
suggested.
Nominal output: 30 mV, 0.02 ohms,
Open circuit turndown voltage: 2mV.
POWERPILE GENERATOR REQUIRED (order sepa-
rately) for 75o mV models: Q302 or Q313 suggested.
Nominal output: 750 mV, 3.4 ohms.
Open circuit turndown voltage: 141 mV.
OPTIONAL SPECIFICATIONS:
WHEN INSTALLING THIS PRODUCT...
Read these instructions carefully. Failure to follow
instructions can damage product or cause a hazardous
condition.
2. Check ratings given in instructions and on product to
make sure product is suitable for your application.
3. Make sure installer is a trained, experienced service
technician.
4. After completing installation, use these instructions to
check out product operation.
FIRE OR EXPLOSION HAZARD
CAN CAUSE PROPERTY DAMAGE, SEVERE
INJURY, OR DEATH
Follow these warnina exactlv.
To avoid dangero& accumulation of fuel gas,
turn off gas supply at appliance service valve
before starting installation and perform Gas
Leak Test after completion of installation.
2.
Do not bend pilot tubing at the cantroi or piiot
after compression nut has been tightened.
Gas ieakage at the connection may resuit.
3.
Aiways instaii sediment trap in gas suppiy
line to prevent contamination of gas controi.
4.
Do not force gas controi knob. Use oniy your
hand to turn gas controi knob. Never use any
tools. if gas controi knob wili not operate by
hand, the controi shouid be repiacsd by a
tempted repair may resuit in fire or expiosion.
1. Disconnect power supply before wiring to prevent
electrical shock or equipment damage.
2. Never apply a jumper across (or short) valve coil
terminals. This may burn out heat anticipator in
thermostat.
IMPORTANT
These gas controis are shipped with protective seals
over inlet and outiet tappings. Do not remove seals
until ready to connect piping.
OPTiONAL PiPiNG PATTERNS-
TRADELiNE MODELS
To facilitate installation, TRADELINE models incorpo-
1. Inlet pressure tap, 1/8 in. NPT.
2. Side outlets.
REPLACEMENT PARTS:
1.392451-1 Energy Cutoff (ECO) Connector.
2. Valve Operators:
Powerpile Operator: VS824.
3. Servo Gas Pressure Regulators.
Standard pressure regulator: V5306.
Step-opening pressure regulator: V5307.
rate side outlets in the standard straight-through body.
Refer to Fig. 3.
To fit existing piping, reducer fittings also are included.
These controls are shipped with side outlets plugged as
shown. if connection is made to optional side outiet, be
sure to install plug in standard straight-through outlet
tapping. Use plug removed from side outlet.
Perform Gas Leak Test when installation is complete.
M A N
UAL GAS
CONTROL KNoB \
INLET
WRENCH
BOSS
9
FiG. 3—TRADELiNE OPllONAL SiDE OUTLETS (stan-
dard capacity models oniy).
Follow appliance manufacturer's instructions if avail-
able; otherwise, use instructions provided below as a
guide.
LOCATiON
Do not iocate the combination gas controi where ad-
verse environments such as steam cleaning, high humidity
or dripping water, corrosive chemicals, dust or grease ac-
cumulation, or excessive heat are prevalent. To ensure
proper operation, follow these guidelines:
Locate in a well ventilated area.
Mount high enough above the cabinet bottom to
avoid exposure to flooding or splashing water.
Ensure that the ambient temperature does not ex-
ceed the ambient temperature ratings for each
component.
Cover if appliance is cleaned with water, steam, or
chemicals ortoavoiddust andgrease accumulation.
Avoid iocating where exposure to corrosive chemi-
cai fumes or dripping water is iikely.
Mount the combination gas control in the appiiance ves-
tibule on the gas manifold. if this is a replacement applica-
tion, mount the control in same location as old control.
LEFT SIDE
OUTLET
OUTLET
STRAIGHT
THROUGH
RIGHT
OUTLET
60-2019-7
Advertisement
