Electronic Function - Makita PV001G Instruction Manual

► Fig.3: 1. Trigger-lock button
► Fig.4: 1. Switch trigger 2. Lock button 3. Trigger-
lock button
To prevent the switch trigger from accidentally pulled, the
trigger-lock button is provided. To start the tool, depress
the trigger-lock button from A (
trigger. Tool speed is increased by increasing pressure on
the switch trigger. Release the switch trigger to stop. After
use, depress the trigger-lock button from B ( ) side.
For continuous operation, depress the lock button while
pulling the switch trigger, and then release the switch
trigger. To stop the tool, pull the switch trigger fully, then
release it.
Speed adjusting dial
The rotating speed can be changed by using the speed
adjusting dial on top of the switch handle. Turn the
speed adjusting dial to align the pointers with your
desired rotating speed indicated on the speed scale.
The rotating speed can be adjusted from 600 (RPM) to
2,200 (RPM), and a target speed can be obtained when
the switch trigger is fully squeezed.
► Fig.5: 1. Speed adjusting dial 2. Pointer 3. Speed scale
NOTICE:
If the tool is operated continuously
at low speeds for a long time, the motor will get
overloaded, resulting in tool malfunction.
NOTICE:
The speed adjusting dial turns between
600 and 2,200 on the speed scale. Avoid turning
the dial back and forwards further as it may cause
damage to the tool.
NOTE: Be sure to read numbers on the scale as an
indicator since the actual speed may fluctuate slightly.
Shaft lock
Press the shaft lock to prevent spindle rotation when
installing and removing accessories.
► Fig.6: 1. Shaft lock
NOTICE:
Never actuate the shaft lock while the
spindle is moving. The tool may be damaged.
Accidental restart preventive function
If you install the battery cartridge while pulling the
switch trigger or locking the switch trigger, the tool does
not start. To start the tool, release the switch trigger, and
then pull the switch trigger.

Electronic function

The tool is equipped with the following electronic func-
tions for easy operation.
Constant speed control
Possible to get fine finish, because the rotating speed is
kept constant even under the loaded condition.
Soft start feature
The soft-start function minimizes start-up shock, and
makes the tool start smoothly.
) side and pull the switch
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing loop handle
CAUTION:
Be sure to hold the tool firmly with
both hands, positioning one hand on the switch
handle and the other on the loop handle, side grip
or tool head.
CAUTION:
Make sure that the loop handle is
installed securely before operation.
1. Place the loop handle over the tool head by pass-
ing the tool head through the loop of the handle.
► Fig.7: 1. Loop handle 2. Tool head
2. Attach the straight end of the loop handle over the
mounting hole on side of the tool head, fitting the guide
ridges on the handle end well into the guide grooves
around the mounting hole.
► Fig.8: 1. Straight end of loop handle 2. Spindle
3. Mounting hole 4. Guide ridge 5. Guide
groove
3. Hold the loop handle and pull the loop end over
the mounting hole on the other side of the tool head,
refining angles to engage the handle position.
4. Install and tighten the hex bolts into the mounting
holes on both sides of the tool head to secure the loop
handle in place.
► Fig.9: 1. Loop end of loop handle 2. Mounting hole
NOTE: The loop handle has an asymmetric shape
that can be applied for left or right hand, making
it more comfortable for you to grip and easy for
polishing.
► Fig.10: 1. Loop handle 2. Tool head 3. Hex bolt
4. Hex wrench
NOTE: The loop handle can be laid down back and
forwards according to your preferred position. Loosen
the hex bolts, move the handle to your desired angle
and then refasten the bolts to lock the angle.
► Fig.11: 1. Loop handle 2. Hex bolt
Installing side grip
CAUTION:
Be sure to hold the tool firmly with
both hands, positioning one hand on the switch
handle and the other on the loop handle, side grip
or tool head.
CAUTION:
Make sure that the side grip is
installed securely before operation.
Screw the side grip tightly into the mounting hole on
either side of the tool head.
► Fig.12: 1. Mounting hole 2. Side grip
11 ENGLISH