Parts Description - Makita UB401MP Original Instruction Manual

Electrical and battery safety
1. Do not dispose of the battery(ies) in a fire.
The cell may explode. Check with local codes for
possible special disposal instructions.
2. Do not open or mutilate the battery(ies).
Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if
swallowed.
3. Do not charge battery in rain, or in wet
locations.
Do not charge the battery outdoors.
4.
5. Do not handle charger, including charger plug,
and charger terminals with wet hands.
Service
1. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
2. Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
First Aid
In case of accident make sure that a first-aid
1.
box is available in the vicinity of the opera-
tions. Immediately replace any item taken from
the first aid box.
When asking for help, give the following
2.
information:
— Place of accident
— What happened
Number of injured persons
—
— Kind of injuries
— Your name
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
WARNING:
Use of this product can create
dust containing chemicals which may cause
respiratory or other illnesses. Some examples of
these chemicals are compounds found in pes-
ticides, insecticides, fertilizers and herbicides.
Your risk from these exposures varies, depend-
ing on how often you do this type of work. To
reduce your exposure to these chemicals: work
in a well ventilated area, and work with approved
safety equipment, such as those dust masks that
are specially designed to filter out microscopic
particles.

PARTS DESCRIPTION

► Fig.3: 1. Cap 2. Pipe 3. Front nozzle
ASSEMBLY
WARNING:
the equipment, switch off the motor or engine and
remove the spark plug cap or battery cartridge.
Otherwise, the fans may move and result in an injury.
WARNING:
the equipment, always put it down. Assembling or
adjusting the equipment in an upright position may
result in serious injury.
WARNING:
tions in the chapter "SAFETY WARNINGS" and
the instruction manual of the power unit.
Mounting the attachment pipe
CAUTION:
ment pipe is secured after installation. Improper
installation may cause the attachment falling off from
the power unit and cause personal injury.
Mount the attachment pipe to the power unit.
1.
Remove the cap from the end of the pipe.
► Fig.4: 1. Pipe 2. Cap
NOTICE:
Do not dispose of the cap since the
cap is necessary for storing the attachment.
2. Turn the lever toward the attachment.
► Fig.5: 1. Lever
3. Align the pin with the arrow mark on the power
unit. Insert the pipe until the release button pops up.
Make sure that the position line is on the tip of the arrow
mark on the power unit, and the arrow mark on the
power unit and the arrow mark on the pipe are facing
each other.
► Fig.6: 1. Release button 2. Arrow mark on the
power unit 3. Pin 4. Position line 5. Arrow
mark on the pipe
4. Turn the lever toward the power unit.
► Fig.7: 1. Lever
Make sure that the surface of the lever is parallel to the
pipe.
NOTICE:
Do not tighten the lever without the
attachment pipe inserted. Otherwise the lever may
tighten the entrance of the drive shaft too much and
damage it.
To remove the pipe, turn the lever toward the attach-
ment and pull the pipe out while pressing down the
release button.
► Fig.8: 1. Release button 2. Lever 3. Pipe
9 ENGLISH
Before assembling or adjusting
When assembling or adjusting
Follow the warnings and precau-
Always check that the attach-