Makita LS0714 Instruction Manual page 21

For tool with the ring (Fig. 30)
WARNING:
• If the ring is needed to mount the blade onto the
spindle, always be sure that the correct ring for the
blade's arbor hole you intend to use is installed
between the inner and the outer flanges. Use of the
incorrect arbor hole ring may result in the improper
mounting of the blade causing blade movement and
severe vibration resulting in possible loss of control
during operation and in serious personal injury.
For tool with the inner flange for other than 20 mm or
15.88 mm holediameter saw blade (Fig. 31)
Country specific
The inner flange has a certain diameter of a blade
mounting part on one side of it and a different diameter of
blade mounting part on the other side. Choose a correct
side on which blade mounting part fits into the saw blade
hole perfectly.
CAUTION:
• Make sure that the blade mounting part "a" on the
inner flange that is positioned outside fits into the
saw blade hole "a" perfectly. Mounting the blade on
the wrong side can result in the dangerous vibration.
Returning the blade guard
Return the blade guard and center cover to its original
position. Then tighten the hex socket bolt clockwise to
secure the center cover. Release the handle from the
raised position by pulling the stopper pin. Lower the
handle to make sure that the blade guard moves
properly. Make sure shaft lock has released spindle
before making cut.
Connecting a vacuum cleaner (Fig. 32)
When you wish to perform clean cutting operation,
connect a Makita vacuum cleaner.
Dust bag (optional accessory) (Fig. 33)
The use of the dust bag makes cutting operations clean
and dust collection easy. To attach the dust bag, fit it onto
the dust nozzle.
When the dust bag is about half full, remove the dust bag
from the tool and pull the fastener out. Empty the dust
bag of its contents, tapping it lightly so as to remove
particles adhering to the insides which might hamper
further collection.
Dust box (optional accessory) (Fig. 34, 35 & 36)
Insert the dust box into the dust nozzle.
Empty the dust box at the earliest possible.
To empty the dust box, open the cover by pushing the
button and throw away sawdust. Return the cover to the
original position and it locks. Dust box can easily be
removed by pulling out while turning it near the dust
nozzle on the tool.
CAUTION:
• Empty the dust box before collected sawdust level
reaches the cylinder part.
Securing workpiece (Fig. 37)
WARNING:
• It is extremely important to always secure the
workpiece properly and tightly with the vise. Failure to
do so can cause the tool to be damaged and/or the
workpiece to be destroyed. PERSONAL INJURY MAY
ALSO RESULT. Also, after a cutting operation, DO
NOT raise the blade until the blade has come to a
complete stop.
CAUTION:
• When cutting long workpieces, use supports that are as
high as the top surface level of the turn base. Do not
rely solely on the vertical vise and/or horizontal vise to
secure the workpiece.
Thin material tends to sag. Support workpiece over its
entire length to avoid blade pinch and possible
KICKBACK.
Vertical vise (Fig. 38)
The vertical vise can be installed in two positions on
either the left or right side of the guide fence or the holder
assembly. Insert the vise rod into the hole in the guide
fence or the holder assembly and tighten the screw to
secure the vise rod.
Position the vise arm according to the thickness and
shape of the workpiece and secure the vise arm by
tightening the screw. If the screw to secure the vise arm
contacts the guide fence, install the screw on the
opposite side of vise arm. Make sure that no part of the
tool contacts the vise when lowering the handle fully and
pulling or pushing the carriage all the way. If some part
contacts the vise, re-position the vise.
Press the workpiece flat against the guide fence and the
turn base. Position the workpiece at the desired cutting
position and secure it firmly by tightening the vise knob.
CAUTION:
• The workpiece must be secured firmly against the turn
base and guide fence with the vise during all
operations.
Horizontal vise (optional accessory) (Fig. 39)
The horizontal vise can be installed on the left side of the
base. By turning the vise knob counterclockwise, the
screw is released and the vise shaft can be moved
rapidly in and out. By turning the vise knob clockwise, the
screw remains secured. To grip the workpiece, turn the
vise knob gently clockwise until the projection reaches its
topmost position, then fasten securely. If the vise knob is
forced in or pulled out while being turned clockwise, the
projection may stop at an angle. In this case, turn the
vise knob back counterclockwise until the screw is
released, before turning again gently clockwise.
The maximum width of the workpiece which can be
secured by the horizontal vise is 120 mm.
CAUTION:
• Grip the workpiece only when the projection is at the
topmost position. Failure to do so may result in
insufficient securing of the workpiece. This could cause
the workpiece to be thrown, cause damage to the blade
or cause the loss of control, which can result in
PERSONAL INJURY.
21