Makita DTR180 Instruction Manual page 15

Cordless rebar tying tool
Hide thumbs Also See for DTR180:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1
devices operate normally. Otherwise, an
accident may occur.
18.
If any of the following phenomena occur, lock
the trigger, turn the power switch off, and
remove the battery cartridge from the tool. If
the tool operates incorrectly, an accident may
occur.
If an operating sound is heard as soon as
the battery cartridge is mounted.
If overheating or abnormal smells or
noises are detected.
When you are taking measures in
response to the error display. (Ask your
local Makita Service Center for repairs.)
When loading or unloading a wire reel.
When you move while holding the tool
during work.
When you do not use the tool.
When you inspect or adjust the tool.
When you remove a stranded wire.
19.
When working on scaffolding, always stabilize
it and work using a posture that will ensure
you maintain your balance. If scaffolding is
unstable, an accident may occur.
20.
When working on a roof or similar locations,
move in a forward direction while working so
that you can see where you are going. If you
move in a backward direction while working, you
may lose your footing and cause an accident.
21.
If you are working in a highly elevated location,
ensure that no one is below you, and pay
attention to ensure you do not drop any tools
while working. Dropping the tool may cause an
accident.
22.
Do not use the tool for any work other than
wire tying. Otherwise, an accident may occur.
23.
Always use Makita's genuine wires. If wires are
not used for a long period of time, they may
rust. Do not use rusted wires. Otherwise, they
may cause an accident.
24.
After tying, check for wire breakage due to
excessive twisting. If any wires are broken,
tying strength will be lost. Adjust the tying
strength, and tie the rebars again.
25.
Securely place the arm against the rebars. If it
is not securely positioned, a clearance will be
created between the rebars, and tying strength will
be compromised.
Important safety instructions for
battery cartridge
1.
Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them
out with clear water and seek medical attention
right away. It may result in loss of your
eyesight.
5.
Do not short the battery cartridge:
(1)
Do not touch the terminals with any
conductive material.
(2)
Avoid storing battery cartridge in a
container with other metal objects such
as nails, coins, etc.
(3)
Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7.
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
8.
Be careful not to drop or strike battery.
9.
Do not use a damaged battery.
10.
The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation
requirements.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on
packaging and labeling must be observed. For
preparation of the item being shipped, consulting
an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
11.
Follow your local regulations relating to
disposal of battery.
12.
Use the batteries only with the products
specified by Makita. Installing the batteries to
non-compliant
in
heat, explosion, or leak of electrolyte.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing
fires,
damage.
void the Makita warranty for the Makita tool and
charger.
15 ENGLISH
products
may
result
a
fire,
excessive
personal
injury
It
will
and
also

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents