Safety Warnings; Save All Warnings And Instructions For Future Reference - Makita DTR180 Instruction Manual

Cordless rebar tying tool
Hide thumbs Also See for DTR180:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1
NOTE: The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE: The declared vibration emission value may
also be used in a preliminary assessment of
exposure.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an
estimation of exposure in the actual conditions of use
(taking account of all parts of the operating cycle such
as the times when the tool is switched off and when it
is running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings
WARNING:
Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow all
instructions listed
in
and/or
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Cordless rebar tying tool safety
warnings
1.
Never point the tool toward a person. Never
put your hands or feet close to the tool tip. If
you accidentally operate the tool while it is
touching someone, it will lead to an unexpected
accident.
2.
Do not load wire while the power to the tool is
turned on. Otherwise, you may get caught in the
wire and
injured.
3.
Do not use the tool without closing the reel
cover. Otherwise, the wire reel may come off and
cause an accident.
below
may
result
electric
shock,
fire
serious
injury.
4.
Be sure to check that the diameters of rebars
to be tied are within the tool capacity before
beginning work.
5.
Wear clothes that have close-fitting hemlines
and sleeves. Do not work with a towel or other
object wrapped around your neck. Otherwise,
they may get caught in the rotating part and cause
an accident.
6.
Be sure to inspect the following points before
using the tool.
Check that no parts are damaged
Check that no bolts are loose
Check that safety devices operate
normally
7.
If any abnormalities are found, stop using the
tool immediately. Do not repair the tool by
yourself. Ask your local Makita Service Center
for repairs. If the tool is used in an incomplete
state, an accident may occur.
8.
When installing the battery cartridge, be sure
to lock the trigger and do not place your finger
on the trigger. Incorrect operation may cause an
accident.
9.
When tying rebars, exercise care not to move
them. If rebars move due to tying, you may be
injured.
10.
Do not touch the wires during the wire tying
process. Otherwise, you may get caught in the
wire and
11.
Do not bring your hands close to the tying
point during the wire tying process. Otherwise,
you may
the
12.
Hold the grip of the tool firmly during the wire
tying process. Otherwise, your wrist may be
twisted or your body may be pulled, which may
result in
13.
Do not move to the next tying point until the
current wire tying process is completed.
Otherwise,
injured.
14.
Pay attention to the end of the wire during the
wire tying process. Otherwise, your hand may be
caught by the end of the wire, and you may be
injured.
15.
Do not touch the contact plate during the wire
tying process. If you need to touch the contact
plate, be sure to lock the trigger, or turn the
power switch off and remove the battery
cartridge.
be
16.
When you have completed the wire tying
process, pull the tool up vertically. Otherwise,
the arm may be caught on rebars, which may
cause an accident.
17.
Be careful not to drop, bump, or hit the tool. If
a strong impact is applied prior to the tool
being used, make sure that the tool is not
damaged or cracked, and that the safety
14 ENGLISH
injured.
get
caught
in
wire
and
injured.
an
injury.
you
may
be
Otherwise, you
may
injured.

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents