Related Manuals for Casio ET-L10 Series
Summary of Contents for Casio ET-L10 Series
- Page 1 Rugged Smart Handheld Terminal ET-L10 Series User’s Guide Be sure to read “Safety Precautions” inside this guide before trying to use your Rugged Smart Handheld Terminal.
- Page 2 Trademarks and Licenses Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and licensed to CASIO COMPUTER CO., LTD. Google™, the Google logo, Android™ and the Android logo are trademarks or registered trademarks of Google LLC. SD, SDHC, SDXC, microSD, microSDHC and microSDXC are trademarks of SD-3C LLC.
-
Page 3: Table Of Contents
USB Type-C Cable ..................33 Important Information in this document is subject to change without advance notice. CASIO Computer Co., Ltd. makes no representations or warranties with respect to the contents or use of this manual and specifi cally disclaims any express or implied warranties of merchantability or fi... -
Page 4: Warning Label
Safety Precautions Congratulations upon your selection of this CASIO product. Be sure to read the following Safety Precautions before trying to use it for the fi rst time. Your neglect or avoidance of the warning and caution statements in the subsequent pages causes the danger of fi... - Page 5 • Should the terminal and/or its options become hot or start to emit smoke or a strange odor, immediately turn off the power and contact your dealer or distributor whom you purchased the product from, or an authorized CASIO service provider. Foreign Objects •...
- Page 6 Warning LCD Screen • Never apply strong pressure to the screen or subject it to strong impact. Doing so can crack the LCD Screen. Prohibitions Should the LCD become cracked, never touch any of the liquid inside. • LCD liquid getting on the skin creates the risk of skin irritation. •...
- Page 7 Built-in Battery Danger • Do not splash water on the terminal or otherwise bring it into contact with water or seawater. Doing so could cause the built-in battery to overheat, rupture or catch fi re. • Do not use or place the terminal in a hot location, such as close to a fi re or heater. Doing so Prohibitions could cause the built-in battery to overheat, rupture or catch fi...
- Page 8 Caution • Store the terminal out of the reach of small children. Power Supply / AC Adapter Warning • Do not use the terminal at a voltage other than the specifi ed voltage. Also, do not connect the terminal to a multi-plug power strip. •...
-
Page 9: Regulatory Information
Backup of All Important Data Caution • Note that CASIO Computer Co., Ltd. shall not be held liable to you or any third party for any damages or loss caused by deletion or corruption of data due to use of the terminal, malfunction or repair of the terminal or its peripherals, or due to the batteries going dead. -
Page 10: Operating Precautions
Operating Precautions Your terminal and its options are precision. Improper operation or rough handling can cause problems with data storage and other problems. Note and observe the following precautions to ensure proper operation. • Do not continue using the battery once it is exhausted. Doing so could result in data loss or corruption. - Page 11 — Frequent repeated charging will shorten the life of the battery. You should wait until the battery is low on charge before charging it. — Charge the battery within the specifi ed temperature range. Note that the specifi ed temperature range varies depending on the equipment used. Refer to the User's Guide (download version).
-
Page 12: About The Waterproofi Ng/Dustproofi Ng
The ET-L10 Series models are waterproof and dustproof. Important! The water- and dust-proofi ng performance of this product is based on CASIO testing procedures. Note also that this performance applies to the product at the time of shipment (delivery to the customer) and is not guaranteed inclusive of the environment in which the product is used. -
Page 13: Accessories And Options
Accessories and Options Rugged Smart Accessories Handheld Terminal Make sure all items listed below are included before using the ET-L10 Series terminal for the fi rst time. • Hand Strap • USB Type-C cable • Eject Pin • USB AC adapter •... -
Page 14: Part Names
Part Names Smart Handheld Terminal (ET-L10) <Top> <Left> <Front> <Right> <Bottom> <Back>... - Page 15 Name Description Receiver Receiver for voice call Charging Status LED Show charging status or battery status Notifi cation LED Show notifi cations of the scanner Illuminance /Proximity Sensor Measure brightness and proximity of object Display words and operation instructions Screen (Touch Panel) Input data in IT-G400 by fi...
-
Page 16: Getting Ready To Use
Getting Ready to Use * In step 2, be sure to fully charge the terminal. 1. Confi rm that all the items listed on page 11 are included in the package. 2. Charge the terminal. (→ page 17) 3. Turn the power on. (→ page 22) Replacing the screen protect sheet A screen protect sheet is affi... - Page 17 3. Using tape , peel off the release fi lm ( ) and attach the screen protect sheet ( ) to the terminal. ⇨ Screen Tips! So that the screen protect sheet attaches uniformly, ensure that its long edge is just touching the edge of the liquid-crystal screen and that the sheet is not skewed.
-
Page 18: Installing And Removing The Ac Adapter
Installing and Removing the AC Adapter The AC adapter must be fi tted with a suitable power plug for the region where the terminal will be used. IInstallation 1. Insert the protruding part of the AC adapter plug into the recess in the top of the AC adapter ( ) until the plug clicks into place ( USB AC adapter... -
Page 19: Charging The Terminal
Charging the Terminal You can charge the ET-L10 using the enclosed USB Type-C cable, the USB AC adapter or the optional cradle-type battery charger. Check the charging status LED to confi rm the ET-L10 charging status. ET-L10 Charging status LED display Red: Charging Green: Charging complete... - Page 20 Cradle-type Battery Charger 1. Plug the USB DC cable into the AC adapter jack in the bottom of the cradle-type battery charger. 2. Plug the USB DC cable into the power cable slit. 3. Connect the USB DC cable to the AC adapter and then plug the AC adapter into the mains power outlet.
-
Page 21: Attaching The Hand Strap
Precautions for Use • Take care not to trap objects such as the strap in the cradle. • The power supply terminal should be cleaned periodically using an implement such as a dry cotton bud. Soiling or dust buildup could cause connection problems. •... -
Page 22: Using A Nanosim Or Microsd Card
Using a nanoSIM or microSD Card This terminal supports nanoSIM cards and microSD cards. To use WAN functions, a SIM card must be installed. Installing the nanoSIM/microSD card 1. Turn the terminal off (shut it down). (The terminal must be shut down.) 2. -
Page 23: Handling The Nfc
Removing the nanoSIM/microSD card 1. Turn the terminal off (shut it down). (The terminal must be shut down.) 2. Remove the nanoSIM/microSD card tray. (Steps 2 and 3 in the installation procedure on page 20) 3. Remove the nanoSIM card or microSD card from the nanoSIM/microSD card tray. 4. -
Page 24: Turning The Power On/Off And Sleep
If charging the built-in battery does not restore its full functionality, the battery has reached the end of its life and must be replaced. Contact your CASIO dealer or an authorized CASIO service provider. -
Page 25: Performing Communications
Performing Communications ® Bluetooth Communication ® Bluetooth interface can also be used to transfer data between two terminals. ® With Bluetooth the two terminals should be located within about fi ve meters from each other, as long as there is nothing blocking the path between them. Important! Observe the following precautions to help ensure that Bluetooth communication is successful. -
Page 26: Rebooting The Terminal
Rebooting the Terminal If the terminal no longer operates normally due to a problem such as an operating error or severe impact, use the procedure below to attempt to restore normal operation. 1. Reboot 2. Forced Reboot Reboot 1. With the screen turned on, hold down the Power key until the Power menu is displayed. 2. -
Page 27: L10 Specifi Cations
ET-L10 Specifi cations ET-L10-WC21 / ET-L10-WC21-AO Remark Qualcomm 1.8GHz Octa Core Android Memory RAM: 2GB FROM: 16GB Display (5.7 inches), 720 x 1440-dot TFT Color LCD Scanner *1 2D Scanner (Imager) Camera 13M pixels Auto Focus Microphone Voice sound input Speaker For voice sound input and voice call at phone WLAN *2... - Page 28 Scanner Specifi cations Item Specifi cation Scanner Method CMOS Imager, 832 × 640, monochrome (Imager) Aimer method Laser 650nm, < 1mW Laser emit Redirected downward: 10 degree angle 1D : 0.127mm Resolution 2D Stacked : 0.169mm 2D Matrix : 0.191mm 0.45 (minimum) or greater 1D : 50 ~ 400mm Readable...
- Page 29 WLAN Spefi cications Item Specifi cation Remark WLAN 2412 MHz – 2472 MHz (1 ~ 13ch) 802.11a/b/ 5180 MHz – 5320 MHz (36 ~ 64ch) g/n/ac Frequency 5500 MHz – 5700 MHz (100 ~ 140ch) Range 5745 MHz – 5825 MHz (149 ~ 165ch) (802.11d: Allowed frequency range can be used according to countries or regions.) 802.11a/g: 54Mbps (maximum)
- Page 30 Wireless WAN Specifi cations Item Specifi cation Communication Data Packet Downlink: 150Mbps (maximum) Baud rate Uplink: 50Mbps (maximum) FDD 1 (1920-1980MHz/2110-2170MHz) FDD 3 (1710-1785MHz/1805-1880MHz) FDD 5 (824-849MHz/869-894MHz) FDD 7 (2500-2570MHz/2620-2690MHz) FDD 8 (880-915MHz/925-960MHz) Frequency FDD 18 (880-915MHz/925-960MHz) range Band FDD 19 (830-845MHz/875-890MHz) FDD 20 (832-862MHz/791-821MHz) TDD 38 (2570-2620MHz/2570-2620MHz) TDD 39 (1880–1920MHz/1880–1920MHz)
- Page 31 NFC Spefi cications Item Specifi cation Remark ISO14443 Type A/B, FeliCa: It can change 0 mm (Contact) by the design Depth of Field of Card or ISO15693: 0 mm (Contact) ~ 50 mm (Maximum) According to JEITA G mode LCD backlight brightness minimum, WLAN ON (with stable RF connection), Buzzer minimum, Vibrator OFF, RF OFF (except for WLAN) •...
-
Page 32: Cradle-Type Battery Charger
Cradle-type Battery Charger You can charge one ET-L10 unit in the cradle-type battery charger. <Top> <Bottom> Name Description Power Contacts Power is supplied to the ET-L10 via these contacts Power Status LED This LED indicates the power status Off : Power off Green: Power on AC Adaptor Jack Connect the AC adaptor here. - Page 33 Plug the USB DC cable into the power cable slit. 3. Connect the USB DC cable to the AC adapter and then plug the AC adapter into the mains power outlet. Place the ET-L10 in the cradle-type battery charger socket so that the terminals in the base of the ET-L10 are touching the power contacts in the cradle-type battery charger.
- Page 34 Precautions for Use • Take care not to trap objects such as the strap in the cradle. • The power supply terminal should be cleaned periodically using an implement such as a dry cotton bud. Soiling or dust buildup could cause connection problems. •...
-
Page 35: Usb Type-C Cable
USB Type-C Cable The USB Type-C cable can be used to connect the ET-L10 to a computer. It can also be used to supply power to the ET-L10. Connecting to a computer 1. Connect the USB Type-C cable to the USB Type-C port on the ET-L10. - Page 36 CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome Shibuya-ku, Tokyo 151-8543, Japan PN410534-003 MO2101-C PN410534-003 2020 CASIO COMPUTER CO., LTD.