Installation; Dust Collection; Switch Action - Makita LC1230 Instruction Manual

INSTALLATION

Positioning the tool
► Fig.1: 1. Hook
When the tool is shipped from the factory, the handle is locked.
Release the handle from the lowered position by lowering it
slightly and removing the chain from the hook on the handle.
Bolt the tool with two bolts to a level and stable surface
using the bolt holes provided in the tool base. This will
help prevent tipping and possible injury.
► Fig.2: 1. Bolt
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function
on the tool.
Blade guard
► Fig.3: 1. Blade guard
When lowering the handle, the blade guard rises automat-
ically. The guard is spring loaded so it returns to its original
position when the cut is completed and the handle is raised.
NEVER DEFEAT OR REMOVE THE BLADE GUARD OR
THE SPRING WHICH ATTACHES TO THE GUARD.
In the interest of your personal safety, always maintain the
blade guard in good condition. Any irregular operation of the
blade guard should be corrected immediately. Check to assure
spring loaded return action of guard. NEVER USE THE TOOL
IF THE BLADE GUARD OR SPRING IS DAMAGED, FAULTY
OR REMOVED. DOING SO IS HIGHLY DANGEROUS AND
CAN CAUSE SERIOUS PERSONAL INJURY.
If the blade guard is especially dirty, use the supplied socket
wrench to loosen the hex bolt holding the center cover.
Loosen the hex bolt by turning it counterclockwise and raise
the blade guard and center cover. With the blade guard so
positioned, cleaning can be more completely and efficiently
accomplished. When cleaning is complete, reverse proce-
dure above and secure bolt. Do not remove spring holding
blade guard. DO NOT DEFEAT OR REMOVE GUARD.
► Fig.4: 1. Blade guard

Switch action

CAUTION:
• Before plugging in the tool, always check to see
that the switch trigger actuates properly and
returns to the "OFF" position when released.
• When not using the tool, remove the lock-off
button and store it in a secure place. This pre-
vents unauthorized operation.
► Fig.5: 1. Lock-off button 2. Switch trigger
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided.
To start the tool, depress the lock-off button and pull the
switch trigger. Release the switch trigger to stop.
Setting for desired cutting angle
CAUTION:
• Always tighten the hex bolt securely after
changing the cutting angle.
► Fig.6: 1. Graduation 2. Lever 3. indicator 4. Vise stop
To change the cutting angle, loosen the lever. Move the
vise stop so that the indicator will point to the desired
graduation. Then tighten the lever to secure the vise stop.

Dust collection

► Fig.7: 1. Dust box
CAUTION:
• Do not touch any part of the dust box except its
handle immediately after operation; it may be
extremely hot and could burn your skin.
This tool is equipped with the dust box to collect dust and
cut chips. When the dust box is full, hold the handle of the
dust box and raise it slightly. Then pull the dust box out of
the tool base. Empty the dust box of its contents.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Socket wrench storage
► Fig.8: 1. Wrench holder 2. Base
The socket wrench is stored as shown in the figure.
When using the socket wrench, pull it out of the wrench
holder. After using the socket wrench, return it to the
wrench holder.
Installing or removing saw blade
► Fig.9: 1. Center cover 2. Hex bolt 3. Socket wrench
4. Blade guard
CAUTION:
• When mounting the blade, make sure that the direc-
tion of the arrow on the surface of the blade matches
the direction of the arrow on the blade case.
• Use only the Makita socket wrench provided to
install or remove the blade. Failure to do so may
result in overtightening or insufficient tightening of
the hex bolt. This could cause a personal injury.
• Do not touch the blade immediately after operation;
it may be extremely hot and could burn your skin.
To remove the blade, use the socket wrench to loosen
the hex bolt holding the center cover by turning it coun-
terclockwise. Raise the blade guard and center cover.
Press the shaft lock to lock the spindle and use the
socket wrench to loosen the hex bolt by turning coun-
terclockwise. Then remove the hex bolt, outer flange
and blade.
► Fig.10: 1. Hex bolt 2. Shaft lock 3. Socket wrench
8 ENGLISH