Makita DTDA040 Instruction Manual page 12

Alarm No.
- A larm f or no c om-
munic ation w ith
th e P C
- I nd ic ation th at th e
tool c an c ommuni-
c ate w ith th e P C
- C h ec k f or th e lamp
and beeper ( w h en
the battery cartridge
is installed )
ASSEMBLY
CAUTION:
Al w ays be sure that the tool is
s w itched off and the battery cartridge is removed
before carrying out any w ork on the tool.
Installing or removing driver bit/
socket bit
Optional accessory
Fig.13
Use only driver bit/socket bit that has inserting portion
shown in the figure. Do not use any other driver bit/
so c ket bit.
For tool w ith shallo w driver bit hole
A = 1 2mm
B= 9 mm
For tool w ith deep driver bit hole
A = 1 7mm
B= 1 4 mm
A = 1 2mm
B= 9 mm
1 . T o install t h e d ri v er bit / so c ket bit, pull t h e slee v e in
t h e d ire c tion o f t h e arro w an d insert t h e d ri v er bit /
so c ket bit into t h e slee v e as f ar as it w ill go.
T h en release t h e slee v e to se c ure t h e d ri v er bit /
so c ket bit.
Fig.14: 1. D ri v er bit 2. S lee v e
2. T o install t h e d ri v er bit / so c ket bit, pull t h e slee v e in
t h e d ire c tion o f t h e arro w an d insert t h e bit-pie c e
an d d ri v er bit / so c ket bit into t h e slee v e as f ar as it
w ill go. T h e bit-pie c e s h oul d be inserte d into t h e
slee v e w it h its pointe d en d f a c ing in. T h en release
t h e slee v e to se c ure t h e d ri v er bit / so c ket bit.
Fig.15: 1. D ri v er bit 2. Bit-pie c e 3. S lee v e
T o remo v e t h e d ri v er bit / so c ket bit, pull t h e slee v e in
t h e d ire c tion o f t h e arro w an d pull t h e d ri v er bit / so c ket
bit out.
Function Status of the tool
No d ata c ommu-
nic ation w h ile th e
tool is c onnec ted to
th e P C .
T h e tool is c on-
nec ted to th e P C
and able to c ommu-
nic ate w ith .
T h e tool perf orms
th e operation test
f or th e L ED ind ic ator
( green/ red ) , ligh t,
and beeper.
Use only these type of driver
bit. F ollow th e proc ed ure
1 . ( Note) Bit-piec e is not
necessary.
To install these types of driver
bits, f ollow th e proc ed ure 1 .
To install these types of driver
bits, f ollow th e proc ed ure 2.
(Note) Bit-piece is necessary
f or installing th e d riv er bit/
soc ket bit.
Status of the LED indicator/beeper
LED indicator
Blinks in yellow.
Blinks in green.
T h e L ED ind ic ator
ligh ts up in green
and th en red . A f ter
th at, th e ligh t turns
on f or a w h ile.
NOTE: I f t h e d ri v er bit / so c ket bit is not inserte d d eep
enoug h into t h e slee v e, t h e slee v e w ill not return to its
original position an d t h e d ri v er bit / so c ket bit w ill not
be secured. In this case, try re-inserting the driver bit/
so c ket bit a c c or d ing to t h e instru c tions abo v e.
NOTE: A f ter inserting th e d riv er bit/ soc ket bit, make sure
that it is firmly secured. If it comes out, do not use it.
Installing hook
Optional accessory
T h e h ook is use f ul to h ang t h e tool. I nstall t h e h ook to
the holes on the tool body.
Fig.16: 1. H ook 2. H ole
OPERATION
CAUTION:
Pressing excessively on the tool w ill
not speed up the drilling. I n f a c t, t h is e x c essi v e pressure
will only serve to damage the tip of your drill bit, decrease
t h e tool per f orman c e an d s h orten t h e ser v i c e li f e o f t h e tool.
CAUTION:
Al w ays secure w orkpieces in a
vise or similar hold-do w n device.
Fig.17
Hold the tool firmly and place the point of the driver bit/
socket bit in the screw head. Apply forward pressure
to t h e tool to t h e e x tent t h at t h e bit w ill not slip o f f t h e
s c re w an d turn t h e tool on to start operation.
NOTICE:
If you use a spare battery to continue
the operation, rest the tool at least 15 min.
NOTICE:
Use the proper bit for the head of the
scre w /bolt that you w ish to use.
NOTICE:
Hold the tool pointed straight at the screw .
NOTICE:
If you tighten the scre w for a long time,
the scre w or the point of the driver bit may be over-
stressed, stripped, damaged, etc. Before starting
your job, al w ays perform a test operation to deter-
mine the proper fastening time for your scre w .
NOTICE:
If the tool is operated continuously until the
battery cartridge has discharged, allo w the tool to rest
for 15 minutes before proceeding w ith a fresh battery.
12 ENGLISH
Action to be taken
Beeper
– R estart th e appli-
c ation sof tw are and
re-c onnec t th e U S B
c able.
–
A series of very
sh ort beeps
–
–