Advertisement
Available languages
Available languages
3. SPECIFICATIONS
Model
No load speed:
Cutting width:
Line size:
Size (L/ W/ H):
Net weight:
4. ASSEMBLY INSTRUCTION
The trimmer is supplied with some components not
assembled. To assemble these, proceed as follows:
4-1 Safety guard assembly
Fix the safety guard onto the motor housing. (Fig. 2 & 3)
1. Put the safety guard onto the motor housing.
2. Rotate the safety guard to the right position.
3. Fix the safety guard on the motor housing with a
screw.
WARNING: Take care against injury from the
blade fitted to the guard for trimming the line to length.
After extending new line, always return the trimmer to its
normal operating position before switching on.
WARNING: Never fit metal cutting elements.
WARNING: Never use it without the safety guard
properly installed. Failure to adhere to this warning can
cause serious personal injury.
4-2 Auxiliary handle assembly
1. Attach the auxiliary handle to the support. (Fig. 4)
2. Insert the bolt to the holes of the handle support and
the handle, and screw the lock knob to the bolt, but
don't screw fully. (Fig. 5)
3. Put the head of the machine on the ground, then
adjust the auxiliary handle to the comfortable position
by another handle for you: (Fig. 6)
3a. Push the adjust button, adjust the tube length for
you want.
3b. Rotate the auxiliary handle on a comfortable angle
for you want.
4. Screw the lock knob to firm the auxiliary handle.
5. STARTING
Before start the trimmer, fix the extension cord into the
hole of the main handle. (Fig. 7 & 8)
Take a secure hold the trimmer and without letting it touch
the grass to be cut, depress the safety lock button and the
switch trigger on the upper and grip.
To switch off the trimmer, release the switch trigger.
(Fig. 9)
WARNING: Switch on motor only when your
hands and feet are away from the cutting means.
8
UR3000
9,000 min
300 mm
Φ1.65 mm
1,016 - 1,256 / 301 / 262 mm
6. UTILIZATION THE TRIMMER
AS AN EDGER
For edging of driveways and paths, transform the trimmer
from the trimmer mode to the edging mode as follows:
1. Hold the tube of the trimmer with one hand and push
the rotation button by another hand. (Fig. 10)
2. Rotate the tube 180° until it locks in the edging mode.
(Fig. 11)
WARNING: To prevent accidental starting which
may cause serious personal injury, always disconnect the
power cord before attempting to rotate the shaft.
7. REPLACEMENT OF THE
CUTTING LINE CARTRIDGE
Your trimmer is supplied with a fully disposable cutting
line cartridge which overcomes troublesome rewinding of
the cutting line.
To replace an empty cutting line cartridge as follows:
1. Press both of the release latch on the spool holder
and boost up it out of the cap (Fig. 12), remove the
empty spool out. (Fig. 13)
2. Put the spring and cap out of the empty spool and into
the new spool, then feed the two cutting lines of the
new spool through the eyelets of the cap. (Fig. 14)
3. Put the new spool into the spool holder, and then
press the cap down till lock into place by the release
latch. (Fig. 15)
8. REFILL OF CUTTING LINE
To refill cutting line:
1. Disconnect the machine from the mains.
2. Remove the empty spool. (Fig. 12 & 13)
3. Cut a new cutting line to less than 8 m and bend it at
the middle.
4. Hook the middle of the new cutting line to the notch
located at the center of the spool between the
2 channels provided for the cutting line. The arrow on
the spool shows the direction of winding the cutting
line. (Fig. 16)
5. Wind the cutting line around the A section (10) in an
orderly placement. Make sure to wind it tight and flat
so that the surface of the wound line is not ragged.
(Fig. 17)
6. Wind all but about 100 mm of the cutting line, leaving
the end temporarily hooked through a line holder (12)
on the side of the spool. (Fig. 18)
-1
2.6 kg
Advertisement
