Adjusting The Fastening Torque - Makita HP001G Instruction Manual

To change the speed, switch off the tool first. Push the
speed change le v er to displa y " 2 " for high speed or " 1 "
for lo w speed. Be sure that the speed change le v er is
set to the correct position b efore operation.
If the tool speed is coming do w n e x tremel y during the
operation w ith displa y " 2 " , push the le v er to displa y " 1 "
and restart the operation.
Selecting the action mode
NOTICE:
Al w a y s set the ring correctl y to y our
desired mode mark. If y ou operate the tool w ith the
ring positioned half w a y b et w een the mode marks, the
tool ma y b e damaged.
NOTICE:
Do not change the action mode w hile
rotating.

Adjusting the fastening torque

CAUTION:
Make sure that the dial is clean. Depending on the work environment, foreign objects such as iron
scraps or chips may adhere to the dial and cause the personal injury.
Fig.8: 1. Dial 2. Indicator 3. Button 4. Green light
The fastening torque can be adjusted in
1. Align marking w ith the arro w on the tool b od y b y turning the action mode changing ring.
2.
Pull the s w itch trigger and release it as soon as the indicator turns on.
3. Push the b utton, and the green light b links.
4. Turn the dial, and adjust the torque level while the green light is blinking.
5. Push the b utton to set the v alue.
NOTE: After pushing the button in step , the green light turns off. If you adjust the torque level again, start over
from step 3 .
NOTE: If y ou lea v e the green light b linking for a w hile, it stops b linking and the v alue displa y ed in the indicator w ill
b e set.
NOTE: Y ou can set the fastening tor q ue le v el in t w o patterns; high speed and lo w speed.
When the le v er displa y s " 1 " , the tor q ue le v el in lo w speed can b e set. When the le v er displa y s " 2 " , the tor q ue le v el
in high speed can b e set.
When y ou change the speed w ith the speed change le v er, the indicator b links three times. After that, dri v e a trial
scre w to check the speed and tor q ue le v el.
NOTE: If y ou pull the s w itch trigger w hile the green light is b linking, the green light turns off and y ou w ill not b e
able to adjust the torque level. To adjust the torque level again, release the switch trigger and turn the dial while the
green light is b linking.
NOTE: If y ou turn the action mode changing ring w hile the green light is b linking, the green light turns off and y ou
will not be able to adjust the torque level. To adjust the torque level again, start over from step .
T o o b tain suita b le tor q ue le v el, perform a test dri v e w ith a w orkpiece of the same material that y ou are going to
scre w .
T he follo w ing sho w s the rough guide of the relationship b et w een the scre w size and graduation.
Lo w speed
Torque level 1
Machine screw M4
Wood S oft ø 3 .5
screw w ood x 2 2
(e.g.
pine)
H ard –
w ood
(e.g.
lauan)
levels in low speed and
2 3 4 5 6
M5 M6
ø 4 .1 x 3 8 –
ø 3 .5 ø 4 .1 x 3 8
x 2 2
NOTE: When y ou change the position from "
other modes, it may be a little difficulty to slide the
action mode changing ring. In this case, s w itch on
and run the tool for a second at the "
then stop the tool and slide the ring to y our desired
position.
Fig.7: 1. Action mode changing ring 2. Mark
3. Arro w
T his tool has three action modes.
• Drilling mode (rotation onl y )
• H ammer drilling mode (rotation w ith
hammering)
• S cre w dri v ing mode (rotation w ith clutch)
S elect one mode suita b le for y our w ork. T urn the
action mode changing ring and align the mark that y ou
selected w ith the arro w on the tool b od y .
levels in high speed.
7 8 9 10 11 12
ø 5 .1 x 5 0 –
– ø 5 .1 x 5 0
8 ENGLISH
13 14 15 16 17 18
–
ø 6 .2 x 6 3
– ø 6 .2 x 6 3
" to
" position,
1 9 20 21
–
–