Makita 9565CR Instruction Manual page 9

Installing or removing wheel guard
(For depressed center wheel,
multi disc / abrasive cut-off wheel,
diamond wheel)
For tool with locking screw type
wheel guard
► Fig.7: 1. Wheel guard 2. Bearing box 3. Screw
WARNING:
• The wheel guard must be fitted on the tool so
that the closed side of the guard always points
toward the operator.
• When using an abrasive cut-off / diamond
wheel, be sure to use only the special wheel
guard designed for use with cut-off wheels. (In
some European countries, when using a dia-
mond wheel, the ordinary guard can be used.
Follow the regulations in your country.)
Mount the wheel guard with the protrusion on the wheel
guard band aligned with the notch on the bearing box.
Then rotate the wheel guard around 180 degrees coun-
terclockwise. Be sure to tighten the screw securely.
To remove wheel guard, follow the installation proce-
dure in reverse.
For tool with clamp lever type wheel
guard
► Fig.8: 1. Wheel guard 2. Bearing box 3. Screw
4. Lever
► Fig.9: 1. Screw
Pull the lever in the direction of the arrow after loosen-
ing the screw. Mount the wheel guard with the protru-
sion on the wheel guard band aligned with the notch on
the bearing box. Then rotate the wheel guard around
180°. Fasten it with the screw after pulling lever in the
direction of the arrow for the working purpose. The
setting angle of the wheel guard can be adjusted with
the lever.
To remove wheel guard, follow the installation proce-
dure in reverse.
Installing or removing depressed
center grinding wheel/Multi-disc
(accessory)
► Fig.10: 1. Lock nut 2. Depressed center grinding
wheel/Multi-disc 3. Inner flange or super
flange
Mount the inner flange onto the spindle. Fit the wheel/
disc on the inner flange and screw the lock nut onto the
spindle.
To tighten the lock nut, press the shaft lock firmly so
that the spindle cannot revolve, then use the lock nut
wrench and securely tighten clockwise.
► Fig.11: 1. Lock nut wrench 2. Shaft lock
To remove the wheel, follow the installation procedure
in reverse.
Super flange
Models with the letter F are standard-equipped with a
super flange. Only 1/3 of efforts needed to undo lock
nut, compared with conventional type.
Installing or removing abrasive disc
(optional accessory)
NOTE:
• Use sander accessories specified in this man-
ual. These must be purchased separately.
► Fig.12: 1. Lock nut 2. Abrasive disc 3. Rubber pad
Mount the rubber pad onto the spindle. Fit the disc on
the rubber pad and screw the lock nut onto the spindle.
To tighten the lock nut, press the shaft lock firmly so
that the spindle cannot revolve, then use the lock nut
wrench and securely tighten clockwise.
To remove the disc, follow the installation procedure in
reverse.
Installing or removing dust cover
attachment (Optional accessory)
WARNING:
• Always be sure that the tool is switched off and
unplugged before installing or removing the dust
cover attachment. Failure to do so causes dam-
age to the tool or a personal injury.
There are three types of dust cover attachment and
each is used in one of different positions.
► Fig.13: 1. Marking A
► Fig.14: 1. Marking B
► Fig.15: 1. Marking C
Place the dust cover attachment so that the side of the
dust cover attachment with the marking (A,B or C) faces
towards the tool head. Snap the pins of the dust cover
attachment in the vent.
► Fig.16: 1. Pin 2. Vent
Dust cover attachment can be removed by hand.
NOTE:
• Clean out the dust cover attachment when it is
clogged with dust or foreign matters. Continuing
operation with a clogged dust cover attachment
will damage the tool.
9 ENGLISH