Makita DVC865L Instruction Manual page 12

NOTICE:
Never pick up water or other liquids or
wet dusts when using the paper pack. Picking up
such things may cause the paper pack breakage.
NOTICE:
When using the cloth filter, make sure
that the float and the float cage are attached on
the tank cover.
NOTICE:
When using the prefilter, make sure
that the powder filter and the damper are used
together.
1. Remove the rubber holder.
► Fig.13: 1. Rubber holder
2.
Extend the paper pack.
3.
Align the paper pack opening with the dust suction
opening of the cleaner.
4. Insert the cardboard part of the paper pack onto
the holder so that it is positioned at the end beyond the
detent protrusion.
► Fig.14: 1. Paper pack 2. Holder
Installing the polyethylene bag
Cleaner can also be used without polyethylene bag.
However, using polyethylene bag is easier to empty the
tank without letting your hands dirty.
Spread the polyethylene bag in the tank. Insert it
between the holder plate and the tank, and pull it to the
hose inlet.
► Fig.15: 1. Holder plate 2. Polyethylene bag
Spread the bag around the top of the tank so that the
cloth filter / prefilter edge can catch and hold the bag
securely.
► Fig.16: 1. Cloth filter / prefilter
NOTE: A polyethylene bag available on the
market can be used. 0.04 mm or thicker one is
recommended.
NOTE: Too much dust will tear the bag easily, so
do not collect the dust more than the half of the bag
capacity.
Emptying the polyethylene bag
WARNING:
Always make sure that the
cleaner is switched off and the battery cartridge is
removed before emptying the polyethylene bag.
Failure to do so may cause an electric shock and
serious personal injury.
CAUTION:
Do not apply a great impact on the
float cage and tank. Applying a great impact may
cause deformation and damage to the parts.
CAUTION:
Empty the tank at least once a day
although this depends on picked-up dust volume
in the tank. Or, the suction force will weaken and the
motor may be broken.
CAUTION:
Do not grab the hook when empty-
ing the tank. Grabbing the hook may cause the hook
to break.
Unhook and lift up the tank cover.
Shake off the dust from the cloth filter / prefilter and then
take the polyethylene bag out of the tank.
► Fig.17
NOTE: Take the polyethylene bag carefully out of the
tank so that the polyethylene bag cannot be caught
and torn by the protrusion inside the tank when emp-
tying it.
NOTE: Empty the polyethylene bag before it
becomes full. Too much dust in the tank may cause
the polyethylene bag to be torn.
Installing the tool box
1. Release the lock of the battery cover, and open
the battery cover.
2. Set the rails on the tool box along the grooves on
the housing.
3. Close the battery cover and apply the lock.
► Fig.18
The tool box is convenient for carrying batteries, pipe,
or cuffs.
► Fig.19
Connecting the hose
NOTICE:
Never force the hose for bending or
stamp it. Never move the cleaner by a hose.
Forcing, stamping and pulling the hose may cause a
breakage or deformation of the hose.
NOTICE:
When picking up large wastes such as
planer carvings, concrete dusts or similar other
than small wastes, use the 38 mm inner diameter
hose (optional accessory). Using the 28 mm inner
diameter hose (optional accessory) may cause a
hose stuffing and damage.
Insert the hose onto the mounting port of the tank and
turn it clockwise until it locks.
► Fig.20
Connecting the attachment with
lock function
Optional accessory
Insert the attachment into the suction inlet until it clicks.
To remove, pull the attachment while pushing the
release button.
► Fig.21: 1. Suction inlet with lock function 2. Release
button 3. Attachment with lock function
NOTE: The attachment with lock function is available
when using the suction inlet with lock function.
► Fig.22: 1. Attachment with lock function 2. Suction
inlet with lock function 3. Suction inlet with-
out lock function
12 ENGLISH