HIKVISION DS-2CD852 Series User Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. DS-2CD852 Series
  6. User manual

HIKVISION DS-2CD852 Series User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

User Manual of Network Camera
Thank you for purchasing our product. If there is any question or request,
please do not feel hesitated to contact us.
This manual may contain several technical incorrect places or printing
errors, and the content is subject to change without notice. The updates will be
added to the new version of this manual. We will readily improve or update the
products or procedures described in the manual.
Version 1.0.0

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION DS-2CD852 Series

Summary of Contents for HIKVISION DS-2CD852 Series

  • Page 1 User Manual of Network Camera Version 1.0.0 Thank you for purchasing our product. If there is any question or request, please do not feel hesitated to contact us. This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual.
  • Page 2 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may cause if any of the warnings is neglected. Cautions: Injury or equipment damage may cause if any of the cautions is neglected.
  • Page 3 2. Do not drop the camera or subject it to physical shock. 3. Do not touch CCD (Charge Coupled Device) modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please turn on the lens cap to protect the CCD from dirt.

  • Page 4: Table Of Contents

    INDEX CHAPTER 1 INTRODUCTION ................................4 1.1 N ..........................4 ETWORK CAMERA UNCTIONS AND EATURES CHAPTER2 INSTALLATION ................................5 2.1 P ..................................5 ANELS ESCRIPTION 2.1.1 Side Elevation of the Camera ............................. 5 2.1.2 Rear Panel Description ................................ 7 2.2 P ..................................

  • Page 5: Chapter 1 Introduction

    Chapter 1 Introduction Network camera is a kind of embedded digital surveillance product that combines the features of both traditional analog camera and net DVS (Digital Video Server). Due to the embedded Linux operation system and the latest Davinci hardware platform of TI, the system operates with high scheduling efficiency.

  • Page 6: Chapter2 Installation

    7. Power Supply, Lens and SD card are Optional. 2.1 Panels Description 2.1.1 Side Elevation of the Camera Fig 2.1.1 Side Elevation of DS-2CD852 series camera Fig 2.1.2 Side Elevation of DS-2CD862 series camera...
  • Page 7 Fig 2.1.3 Side Elevation of DS-2CD752、DS-2CD762 series camera Fig 2.1.4 Side Elevation of DS-2CD752MF-FB(H)、DS-2CD762MF-FB(H) series camera...

  • Page 8: Rear Panel Description

    2.1.2 Rear Panel Description Fig. 2.1.5 Rear Panel of DS-2CD852, DS-2CD862 series camera 1、Standard Ethernet (UTP) RJ45 (10M/100M self-adaptive). 2、1 channel voice talk input,3.5mm audio interface, 2.0～2.4Vp-p, 1kΩ. 3、1 channel voice talk output, 3.5mm audio interface, electric line level, 600Ω. 4、ANT, connect to Antenna.
  • Page 9 Fig. 2.1.6 Rear Panel of DS-2CD752 、DS-2CD762 series Address& protocols dial switch, define for dial switch: , from 1 to 5 dial switch function as follows: Switch Function SHARP SOFT NAGC SAGC Notices: There are invalid dial switches for DS-2CD752、DS-2CD762 series from 6 to 10;...

  • Page 10: Product Installation

    2.2 Product Installation 2.2.1 Box camera Installation Box camera can be fixed in both metope and ceiling. Customers can choose whichever way according to their specific needs. Please follow the steps below:(Take fixing in ceiling as an example, fixing in metope follows the same rule).Choose the fixing method and fix the camera bracket accordingly.

  • Page 11: Dome Camera Installation

    2.2.2 Dome camera Installation Dome camera can be installed include hold equipment,ceiling mounted,cylinders and other styles. Client can be installed in accordance with their own ways to achieve the installation.Please according the following specific steps to install (take ceiling mounted as example), when the wall is wood, use the self-tapping screws to fix the ceiling plate to the wall surface.

  • Page 12: Topological Graph Of Network Camera

    2.2.3 Topological graph of network camera Fig 2.2.8 Topological Graph of DS-2CD852、DS-2CD862 series Physical Interface Connection Connect to network devices, such as switch , HUB, etc. UTP Network Interface Please refer to Appendix B for pin Definition. Connect to audio input devices such as active tone (2.0～ Audio Input（AIN）...
  • Page 13 system. Tested following models current graphics cards support softwareinstalled,ATIRadeonX1650,X1600,X1550,X1300,X800,X600,X550,HD2400,HD2600,NVIDIA GeForce 8600GT,8500GT,8400GS,7600,7300LE,6600LE,6200LE,INTEL915/945G,pay attention to graphics driver must support hardware scaling function. Double click the software and you will see the wizard shown as below:   Click “Next” to continue, and input the user information, software installed location according to the hints.

  • Page 14: Ds-2Cd852, Ds-2Cd752 Series Camera Menu Illustrate And E-Ptz Operation

    Click the “Finish” button to close the dialog box. After the client software being installed, you can find the remote client software through “Start” -> “Program” on your PC DS-2CD852, DS-2CD752 series camera Menu illustrate and e-PTZ operation 2.4.1 752/852 series products e-ptz function Under the resolution of QCIF/CIF/DCIF/2CIF/VGA/D1/SVGA, support pan\tilt\zoom operation, pan and tilt operation can be carried out only after zooming in，Support 127 preset positions（95 excluded，used to call menu）...
  • Page 15 ※ U P ↑: Means select OSD menu item ※ DOWN↓: Means select OSD menu item ※ LEFT ← : Means select parameter on OSD ※ RIGHT→: Means select parameter on OSD Attention： Parameter on OSD exception “FLICKER CONTROL”, others become effective in time Parameter on OSD of “RESOLUTION”...
  • Page 16 ◆Shutter AUTO×2 AUTO×5 “OFF” The regulation of shutter exposure time is default. “AUTO×2” The regulation of shutter exposure time is considerably wider. “AUTO×5” The regulation of shutter exposure time at its maximum. DS-2CD852MF-E 50Hz 60Hz Resolution Auto×2 Auto×5 Auto×2 Auto×5 DCIF QCIF 4CIF...
  • Page 17 SVGA UXGA 12.5fps 12.5fps 5fps 10fps 10fps 5fps HD720p 25fps 12.5fps 5fps 15fps 15fps 5fps ◆AUTO GAIN MEDIUM HIGH You can set up different auto gain values separately in the condition of low illumination, and increase the picture brightness. This function may not only be independent employment, but also coordinate with option selections in shutter establishment, in order to achieve better low light illumination mode effect.
  • Page 18 In the condition of low illumination, the auto mode has a better noise cut-down effect compared with color mode. ◆WHITE BALANCE Auto “Auto” Enable the auto W&B of the current screen “OFF” Based on the current W&B state，no more auto adjustment. ◆EFFECTS MODE SEPIA NEGATIVE...
  • Page 19 If B&W is switched to color mode，this function is compelled to be “OFF”。 ◆MIRROR LEFT RIGHT UP BOTTOM CENTER...
  • Page 20 ◆e-PTZ “OFF” Means support mechanical PTZ only “ON” Means support e-PTZ function only SAVE ◆EXIT CANCEL DEFAULT This mode is employed after clicking “enter” buttons.
  • Page 21 “SAVE” Save the current configuration “CANCEL” Cancel with the current operations，restore to the configuration before carrying out the operations. “DEFAULT” Restore to the default configuration...

  • Page 22: 762/862 Series Menu Instruction

    2.4.3 762/862 series menu instruction 1、Display menu Invoke Pre-set position95；Double click presetting points of “95 ”,main menu display on screen . <MAIN MENU> LANGUAGE ENGLISH RESOLUTION HD(1280*720) FRAME 25fps LENS SHUTTER 1/25s AUTO GAIN DAY/NIGHT WHITE BALANCE BACKLIGHT COMP. MANUAL … MIRROR <EXIT>...
  • Page 23 ◆Resolution This option is used for displaying the current resolution, can’t be controlled by “left” “right” buttons. But it can be controlled by remote setting option. Notice: as for DS-2CD862、DS-2CD762 series camera , they are support XVGA(1280*960) per second 12.5 frames and HD720P(1280*720) ,VGA(640*480) per second 25frames ◆Frame This option is used for displaying the output frame rate, can’t be controlled by “left”...
  • Page 24 When select “ Day” or “Night” mode at “DAY/NIGHT” option, Auto Gain support High、Middle、 Low、Off option. When select “Auto ” mode , Auto Gain will display “---” option. You can set up different auto gain values separately in the condition of low illumination, and increase the picture brightness.
  • Page 25 ◆White balance ATW1 ATW2 MWB… When select “Night” mode , white balance option will display “---”, means not support setting by manual. When select “Auto” or “Day” mode ,white balance support setting by manual; ATW 1 ATW 2 MWB SETTING Auto or Day TEMP.
  • Page 26 ◆Backlight Comp. Manual… Support “Off” and “Manual…” two mode; When select “Manual…” at Backlight Comp. option, the position and size of Backlight Comp. can be setting by manual. BACKLIGHT COMP. MANUAL… POSITION… SIZE… Manual…(click DOWN BACK Iris[+],entry OSD) LEFT RIGHT Notice ：...
  • Page 27 ◆Mirror Left Right Up Bottom Center Support “Off”、”Left Right”、”Up Bottom”、”Center” mode, and set by “left” “right” buttons Save ◆Exit Cancel Default This mode is employed after clicking “enter” buttons. “SAVE” Save the current configuration “CANCEL” Cancel with the current operations，restore to the configuration before carrying out the operations.

  • Page 28: Chapter3 Parameters Configuration

    Chapter3 Parameters Configuration There are several network parameters of the camera those need to be set after the hardware installation. Those parameters including IP address, subnet mask and port number, etc. which can be set through various kinds of methods, 2 of them are introduced as below. 1.
  • Page 29     Fig. 3.3 Set the Security Level The default IP of the camera is 192.0.0.64 with 8000 as the default port, admin as the administrator, and 12345 as the password. The administrator can create up to 15 separate operators with different right levels.
  • Page 30 To login the camera through IE, input the IP address in the address column, and the “Login” dialog box will pop-up as Fig. 3.4. Input your user name and password, and then click “Login” to enter the “preview” page. Double click the “Camera 01” channel or “Preview” button to preview the video as Figure 3.5.

  • Page 31: Configuration Via Client Software 4000(2.0)

    Note: If plug the SD card into the camera, user should enter the “config” and select “other function” to format the SD card. For more specific information of “Remote Parameters Config”, please refer to “Instructions of Client Software (version 4.01)” from Section 2.5.3 of remote-distance parameter settings. Instructions can be found in the client software4.01 in the path of “Start”...
  • Page 32 Fig.3.2.1 Register Administrator Enter the registered user name and password as Fig. 3.3.2. Click “Login” to enter the “Preview” menu as Fig. 3.2.3.   Fig. 3.2.2 User Login   Fig. 3.2.3 Preview Menu Click the “Configure” button in Fig. 3.2.4, and then right click the blank spaces in the middle. Click the “Create Root Node”...
  • Page 33   Fig. 3.2.4 Create Root Node   Fig. 3.2.5 Area Properties Input the area name (you can create whatever name you like) and click “OK” as Fig. 3.2.6. Then right click the area name you have just created as Fig. 3.2.7.
  • Page 34   Fig. 3.2.6 Area Name Adding Completed   Fig. 3.2.7 Right Click the Area Name Click “Add Device”, and the “Server Properties” dialog box will pop up as Fig. 3.2.8. Input your “Server Name” and select “HC” from the “Server Type” option. Select “Normal” from “Register” option. Input your camera IP in “Server IP”, e.g.
  • Page 35   Fig. 3.2.8 Add Device   Fig.3.2.9 Camera Adding Completed Click the “Preview” button to enter the “Preview” menu as Fig. 3-2-10. Double click the channel name in the left tree to preview the pictures.
  • Page 36 Double click the channel   Fig.3.2.10 Preview Menu Please refer to “Network Video Surveillance Software Operation Instruction (4000)” for more detailed parameters configuration. You can find the document in PC Operating System after the installation of client software 4000 by selecting “Start”-> “Program”-> “client software 4000”.  ...

  • Page 37: Chapter 4 Wan Access

    Chapter 4 WAN Access The IP protocol supports WAN access based on PPPoE dial up function. Make sure that the software you are using supports the function before using these network functions. 4.1 WAN access has a fixed static IP Network Camera If the network camera adopt static IP address directly access the public network.

  • Page 38: Wan Access Without A Fixed Static Ip Network Camera

    4.2 WAN Access without a fixed static IP Network Camera If the network camera through PeanutHull domain name or other means of public Network 1、 access. Please connect the camera to router, set the camera IP address, netmask, gateway and routers in the same network segment.
  • Page 39 2、If the network camera through IPSERVER access the public network. The camera support PPPoE auto dial-up function, connect camera to Modem for dial-up access the ADSL network and get an public IP address; First, through local network access network camera, select[Configure]----[Network Configuration] dialog box, enable PPPoE, fill PPPoE user name and password and confirm the password, Please restart the network after the completion of the camera.

  • Page 40: Chapter 5 Common Failures And Maintainance

    Chapter 5 Common failures and maintainance 1、Power on failure Check if the power plug is fixed into the socket or if the power supply is working correctly. 2、Image blurry Check if the lens connector is correct. There are two types of bayonets—the C and CS which are different;...

  • Page 41: Appendix 1 Sadp Introduction

    Appendix 1 SADP Introduction  1. Brief introduction SADP (Search Active Devices Protocol), can automatically search IP cameras in LAN. User can modify the IP address, subnet mask and port of the device without visiting IP address of the device. Additionally, password of the super user in this device can be recovered as default. SADP software needs to support sadp, so we should install WinPcap at first, which is placed at the directory of SADP software.
  • Page 42   Input new IP address, subnet mask, and port number, and click ‘save’ button. If a dialog pops up, showing ‘saved successfully’, that means you have modified the configuration information; if ‘saving failed’ turns up, click the ‘cancel’ button to quit it. 4.

  • Page 43: Appendix 2 Port Map

    Appendix 2 Port Map  Note: The following setting is about TP-LINK router (TL-R410), which is maybe distinct from other router’s setting. 1. Firstly, select the router’s WAN connection Type. As the following Fig. shows:   2. Set the “network parameter” of the router as the below figure. The setting includes subnet mask and gateway.
  • Page 44   As the above mentioned setting, we map the router’s port 80, 8000 to the network camera 192.168.1.23; and port 81, 8001 to the network camera 192.168.1.24. In this way, user can visit the 192.168.1.23 through visiting the router’s port 80, 8000. Note: The port of the network camera cannot conflict with other ports.

  • Page 45: Appendix Technology Specification

    Appendix Technology Specification Table 1 Parameter Model DS-2CD852MF-E DS-2CD852MF-E(CUT) Camera Image Sensor 1/3 inch CMOS Effective Pixels 1600(H)×1200(V) 0.5Lux/F1.2 Min. Illumination 0.1Lux/F1.2, sensitization X5 Electronic Shutter Auto Auto Iris Lens ------ Day&Night Electronic Lens Option Lens Mount C/CS mount Video Output 1Vp-p Composite Output(75Ω/BNC) Compression Standard Video Compression...
  • Page 46 Alarm Output 1 channel relay output Others Working Temperature -10℃~60℃ Power Supply AC24V±10%/DC12V±10%, PoE (Power over Ethernet). Power Consumption 4W MAX Dimensions (mm) 64.8x63x157.5 Weight 600g Notice: (-E) illustration of support PoE (power over ethernet) (-F) illustration of support local SD card storage (-W) illustration of support IEEE802.11g wireless Ethernet criterion Table 2 Parameter...
  • Page 47 1 RJ45 10M/100M self-adaptive Ethernet port and 1 Communication RS-485 interface Alarm Input 1 channel relay input Alarm Output 1 channel relay output Others Working Temperature -10℃~60℃ AC24V±10%/DC12V±10%, (Power over Power Supply Ethernet). Power Consumption 4W MAX Dimensions (mm) 68.5x63x157.5 Weight 600g Notice: (-E) illustration of support PoE (power over ethernet)
  • Page 48 SD Card Local Recording Support Heartbeat Support Password Protect Support TCP/IP,HTTP,DHCP,DNS,RTCP,RTSP,PPPoE Protocols (FTP,SMTP,NTP,SNMP addible). Interface Voice Talk Input 1 channel (2.0～2.4Vp-p,1kΩ) Voice Output 1 channel (Line level, 600Ω) 1 RJ45 10M/100M self-adaptive Ethernet port and 1 RS-485 Communication interface Alarm Input 1 channel relay input Alarm Output 1 channel relay output...
  • Page 49 Frame Rate 50Hz:25fps(704x576),25fps(1280x 720) 12.5fps(1600x1200),12.5fps(1600× 912) 25fps(1280×720, 640×480) 12.5fps(1280×960) 60Hz: 30fps(704x480),15fps(1280x720) 10fps(1600x1200),12.5fps(1600×9 Function e-PTZ Support Motion Detect Support Dual Stream Support Card Local Support Recording Heartbeat Support Password Protect Support Protocols TCP/IP,HTTP,DHCP,DNS,RTCP,RTSP,PPPoE(FTP,SMTP,NTP,SNMP addible) Interface Voice Talk Input 1 channel(2.0～2.4Vp-p,1kΩ) Voice Output 1channel (Line level, 600Ω) Communication 1 RJ45 10M/100M self-adapted Ethernet port and, 1 RS-485 interface...

This manual is also suitable for:

Ds-2cd862 seriesDs-2cd752 seriesDs-2cd762 seriesDs-2cd852mf-eDs-2cd762f-fbhDs-2cd862mf-e ... Show all

Table of Contents