Sony ZV-1 Service Manual page 14

Self-diagnosis Code
Repaired Block
by: Function
E 61 30
E 62 00
E 62 01
E 62 02
E 62 04
E 62 10
E 62 11
E 62 12
E 62 20
E 91 01 *2
E 92 00
E 94 00 *2
E 94 02
E 95 00 *2
E 95 01
E 95 02 *2
*1: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items. After the adjustment,
make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
*2: Function of this code is not provided in this unit.
Detailed Symptom/State
Code
Reset position detection error on the
stepper iris initializing
Steadyshot does not work well.
(With PITCH angular velocity
sensor output stopped)
Steadyshot does not work well.
(With YAW angular velocity sensor
output stopped)
Abnormality of IC for steadyshot.
Image vibration correction during
steadyshot does not work.
Shift lens initializing failure
Shift lens overheating (PITCH)
Shift lens overheating (YAW)
Abnormality of thermistor
Abnormality when flash is being
charged
Battery/Dry cell distinction defect
Fault of writing or erasing the
internal memory
BGM data error
GPS hardware error
Acceleration sensor hardware error
Electronic compass hardware error
(GPS hardware error)
Correction
Turn the power on to open lens barrier. Disconnect the
battery or power cord, and then connect again. And
confirm that the iris blades in lens are working.
If iris blades do not work, check the iris motor drive
circuit in lens drive block. If iris blades work normally,
confirm that they are closing completely and confirm
following items.
•
Case of the iris blades do not close normally. Replace
the lens block.
•
Case of "E: 61: 30" is appeared and iris blades closed
completely. Confirm that communication with lens
block is normal.
•
Case of LCD is not displayed normally, check that
connection between imager board and main board.
•
Case of LCD is displayed normally, replace the lens
block.
The peripheral circuit of the PITCH angular velocity
sensor may be faulty.
Replace the board that contains this peripheral circuit.
The peripheral circuit of the YAW angular velocity
sensor may be faulty.
Replace the board that contains this peripheral circuit.
Check signal line connections from CPU through
steadyshot IC to PITCH/YAW drive.
When there is no problem with the connections, replace
the board that contains this peripheral circuit.
The image vibration angular velocity sensor peripheral
circuit may be faulty.
Replace the board that contains this peripheral circuit.
Replacement of lens block. *1
If an error occurs again, steadyshot circuit may be faulty.
Replace the board that contains this peripheral circuit.
Check signal line connections from CPU through
steadyshot IC to PITCH/YAW drive.
When there is no problem with the connections, check
whether this error is due to the lens or the board.
Replace the faulty lens or board.
Check signal line connections from CPU through
steadyshot IC to PITCH/YAW drive.
When there is no problem with the connections, check
whether this error is due to the lens or the board.
Replace the faulty lens or board.
Check signal line connections from CPU through
steadyshot IC to PITCH/YAW drive.
When there is no problem with the connections, check
whether this error is due to the lens or the board.
Replace the faulty lens or board.
Checking of flash unit or replacement of flash unit.
Turn power off and turn power on again.
Turn power off and turn power on again.
The CPU may be faulty.
Replace the board that contains this peripheral circuit.
Check the signal line connection for GPS.
When there is no problem with the connections, replace
the board that contains this peripheral circuit.
Turn power off and turn power on again.
When this error is not cleared, the peripheral circuit of
the acceleration sensor may be faulty.
Replace the board that contains this peripheral circuit.
The peripheral circuit of the electronic compass may be
faulty.
Replace the board that contains this peripheral circuit.
Sony CONFIDENTIAL
For Authorized Servicer
6
SYS SET