Download Print this page

Advertisement

Quick Links

Standard Operating Procedure
Hansa C27HS Chipper
Version 1 Issue date: 10/03/2017
Page 1 of 6
Section 1: Equipment Identification and Supplier details
Name
Recommended Use
Manufacturer / Importer
Emergency Contact details
Links to product
information
Does this equipment require a daily check or inspection and entry in a log book?

Section 2.0 Emergency Stop:

Section 3: Hazards Identification

Hansa C27hs Chipper
Chipping of timber, branches and vegetative matter up to 150 mm
diameter. NOT suitable for flax, bones, stones or other hard
substances.
Hansa NZ
www.hansachippers.co.nz
Garry Bull (Upper Hutt Hire) 027 742 6583
https://www.youtube.com/watch?v=_8LmgKpCYPM
(Model shown on Youtube varies slightly from C27HS Model: Our version does not have
rotating turret mount, and is 'fixed mounting'.)
http://forestry.worksafe.govt.nz/assets/resources/WSNZ-2165-
Safe-Use-of-Wood-Chippers-FS-6-0-FA1-LR.pdf
The Yellow Feed Roller Control Handle can be used to stop any material
entering the chipping zone. Moving the Feed Roller Control Handle will
stop feeding material into the chipper, but it will not stop the engine.
In an emergency, TURN THE KEY TO OFF.
Note that the Cutter / Flywheel will still continue to rotate, and may take
up to a minute to stop.
NEVER REMOVE THE SAFETY GUARDS from the Chipper. Never
operate the Chipper with the safety guards removed.
NEVER place hands or feet in the feed anywhere near the feed
chute. RISK of limbs being crushed or severed. If a blockage
occurs turn off the engine, and allow the machine to come to a
COMPLETE STOP before clearing obstructions.
DANGER: RISK OF FLYING DEBRIS.
Operator must wear protective eyewear and heat protection.
No other persons or animals are permitted within 10 meters of
the Chipper while in operation.
Exhaust gases are poisonous. DO NOT run the engine indoors
or within a confined space. Always ensure there is adequate
ventilation.
Do not operate on concrete or bitumen. Risk of ejected
material causing injury.
20 Goodshed Road Upper Hutt
Phone 04 528 4473
No

Advertisement

loading

Summary of Contents for Hansa C27HS

  • Page 1: Section 3: Hazards Identification

    Emergency Contact details Garry Bull (Upper Hutt Hire) 027 742 6583 Links to product https://www.youtube.com/watch?v=_8LmgKpCYPM (Model shown on Youtube varies slightly from C27HS Model: Our version does not have information rotating turret mount, and is ‘fixed mounting’.) http://forestry.worksafe.govt.nz/assets/resources/WSNZ-2165- Safe-Use-of-Wood-Chippers-FS-6-0-FA1-LR.pdf Does this equipment require a daily check or inspection and entry in a log book? Section 2.0 Emergency Stop:...
  • Page 2: Section 4: Noise And Vibration

    Standard Operating Procedure Hansa C27HS Chipper Version 1 Issue date: 10/03/2017 20 Goodshed Road Upper Hutt Page 2 of 6 Phone 04 528 4473 Risk of inhalation of particulate dust when chipper old timber, as the chipping process may produce dust. Wear breathing protection if chipping older timber.
  • Page 3 Standard Operating Procedure Hansa C27HS Chipper Version 1 Issue date: 10/03/2017 20 Goodshed Road Upper Hutt Page 3 of 6 Phone 04 528 4473 Vibrations a (m.s Not available. No direct prolonged contact with vibrating parts. Section 5: Work Zone 5.1 Work Zone Control or Isolation...
  • Page 4 Standard Operating Procedure Hansa C27HS Chipper Version 1 Issue date: 10/03/2017 20 Goodshed Road Upper Hutt Page 4 of 6 Phone 04 528 4473 3. Check for damage and any loose parts. Check the condition of the safety stop button.
  • Page 5 Standard Operating Procedure Hansa C27HS Chipper Version 1 Issue date: 10/03/2017 20 Goodshed Road Upper Hutt Page 5 of 6 Phone 04 528 4473 Setting the desired AutoTrip setting The AFC has 19 different pre-set positions at which the feed will stop.
  • Page 6: Section 9: Transport

    Upper Hutt Hire Ltd shall not be liable in any way for any reliance by any person or entity on the accuracy of information or data contained in this document or its attachments. Revision date March 2022 (SOP based on C27hs Chipper Manual Issue 1 04/10/2016...