Advertisement

Quick Links

Phone: 800-669-1303 or 801-561-0303
Fax: 801-255-2312
e-mail: treborservice@idexcorp.com
PURUS CP
Operation / Maintenance
Manual
SERIAL NUMBER (located on top of product):
02/10/2016– MPCP-A

Advertisement

Table of Contents
loading

Summary of Contents for Idex Trebor PURUS CP

  • Page 1 Phone: 800-669-1303 or 801-561-0303 Fax: 801-255-2312 e-mail: treborservice@idexcorp.com PURUS CP Operation / Maintenance Manual SERIAL NUMBER (located on top of product): 02/10/2016– MPCP-A...
  • Page 2: Table Of Contents

    CONTENTS INTRODUCTION......................3 INTENDED USE AND AUDIENCE ..............4 SAFTEY ........................5 SAFETY PRECAUTIONS ................... 5 2.1.a General Safety ..................5 INSTALLATION ......................6 UTILITIES / HOOK-UP ..................7 UNPACKING ...................... 7 ORIENTATION ....................7 FLUID CONNECTIONS ..................7 OPERATION ......................... 8 PRINCIPALS OF OPERATION ................
  • Page 3: Introduction

    INTRODUCTION Purus CP – A Revolutionary PFA High-Purity, Low-Pulsation Pump! TREBOR’S Purus CP diaphragm pump offers a unique solution to critical applications requiring stable flow and low pulsation. With a revolutionary injection molded PFA design, Trebor has created an ultrapure pump utilizing proven components with minimal parts. This manufacturing approach has created a reliable, leak proof, disposable pump that costs less than most competitors’...
  • Page 4: Intended Use And Audience

    INTENDED USE AND AUDIENCE The Purus CP pump is designed to safely pump liquids up to 120°C. This manual only covers the Trebor Purus CP pump and pump accessories provided by Trebor. The Purus CP pump is not to be used for proposes other than that which it is designed for.
  • Page 5: Saftey

    SAFTEY SAFETY PRECAUTIONS This section provides important information for safe operation of the Purus CP pump. The equipment described in this manual can be used to pump hazardous chemicals that can be dangerous. Local policies and procedures for safely operating any Trebor Purus CP pump(s) supersede the safety considerations listed below.
  • Page 6: Installation

    INSTALLATION Ensure all system interlock and safety devices are functional prior to operation (refer to Section 2, Safety Requirements). Before starting the system, it is important to read and understand Section 4, Operation. Only trained, qualified, authorized personnel should operate this pump. Figure 3-1: Dimensions (in / [cm]) PAGE 6 PURUS CP PUMP OPERATION / MAINTENANCE MANUAL...
  • Page 7: Utilities / Hook-Up

    UTILITIES / HOOK-UP Utility Pump  3/8” FNPT per head. Air Inlet:  20-80 PSIG (.14 – .55 MPa), clean dry air or inert gas Air Supply:  1/2” Flare Fluid Ports:  1/2” Tube Stub (Optional)  1/2” Pillar Super 300 (Optional) ...
  • Page 8: Operation

    OPERATION PRINCIPALS OF OPERATION  The Purus CP accomplishes near pulseless flow by Cross-Phase operation (refer to the following step-by-step illustration):  Chamber 1 – pressure / Chamber 2 – vacuum.  Chamber 1 – pressure / Chamber 2 – pressure (crossed-phase). ...
  • Page 9: Contoller

     Refer to Troubleshooting Section 7 if pump fails to start or contact Trebor for further assistance. ATTENTION: The pump should be operated with clean, dry air or nitrogen. Particulate, water and oils in the air supply can damage or contaminate the pump air chamber. NOTE: The Purus CP can be operated dry for extended periods up to 24 continuous hours.
  • Page 10 Figure 4-2: Pressure and Flow Capacity Chart The preceding chart defines a region of operation over which the Purus CP pump may be operated with a PC15 pump controller with a discharge flow variance of less than +/-1.5% of nominal value. Figure 4-3: Purus CP Recommended Temperature Curve PAGE 10 PURUS CP PUMP OPERATION / MAINTENANCE MANUAL...
  • Page 11: Inspection And Maintenance

    INSPECTION AND MAINTENANCE MAINTENANCE The Purus CP has no serviceable parts. Pumps removed from service, decommissioned, or dismantled should be decontaminated and disposed of per company policy. MATERIALS LIST 5.2.a Wetted Materials  PFA and PTFE 5.2.b Non-wetted Materials  PVDF and PP NOTE: PURUS CP has no serviceable parts.
  • Page 12: Pc15Cp (Optional) Installation

    PC15 (OPTIONAL) INSTALLATION PC15 OVERVIEW The PC15 Pump Controller is designed specifically to operate Trebor’s Purus CP pump. Cross-phase timing results in overlapping pump strokes which produces a near pulse-less pump output. PC15 controllers can be configured depending on flow requirements (See QIG manual) PC15 INSTALLATION The PC15 pump controller can be installed in any orientation.
  • Page 13: Pc15Cp Utilities / Hook-Up

    PC15 UTILITIES / HOOK-UP Utility Pump  3/8” Diameter supply tube. Air Inlet:  Air Supply: 50-80 PSIG (.55±.03 MPa Max), clean dry air or inert  Power 24VDC - 500mA  Controller Weight: 4.4 lbs (2.0 Kg) ATTENTION: Air supplied to the PC15 pump controller must be regulated to 50 - 80 PSIG to operate the vacuum venturi.
  • Page 14: Pc15Cp Controller Operation

    PC15 CONTROLLER OPERATION Ensure that all system interlock and safety devices are functional prior to operation. Before starting the system, it is important to read and understand the PC15PC manual. Only trained, qualified, authorized personnel should operate this pump controller. The controller is operated by using the buttons located on the PLR, see Table 6-1.
  • Page 15: Troubleshooting

    TROUBLESHOOTING PUMP SYMPTOM CAUSES SOLUTIONS    Bubbles in Fluid Diaphragm puncture Replace pump assy. (Non Discharge Serviceable)   Loose inlet fitting Check and tighten all fittings on the suction line feeding the pump.    Fluid Leaks Weld failure Replace pump assembly (Non Serviceable)
  • Page 16: Warranty And Exclusions

    WARRANTY AND EXCLUSIONS See the Trebor Standard Limited Warranty at www.idex-hs.com/support/trebor/downloads/TreborStandardLimitedWarranty_02-07.pdf PAGE 16 PURUS CP PUMP OPERATION / MAINTENANCE MANUAL...
  • Page 17: Contact Information

    CONTACT INFORMATION GENERAL CONTACT INFORMATION Web: www.teborintl.com Phone Number: (801) 561-0303 Toll Free Number: (800) 669-1303 Fax Number: (801) 255-2312 Email: treborinfo@idexcorp.com treborsales@idexcorp.com Address: Trebor International 8100 South 1300 West West Jordan, Utah 84088 U.S.A. TECHNICAL SUPPORT Email: treborservice@idexcorp.com Phone Number: (801) 244-6156 REGIONAL REPRESENTATIVES Web:...

Table of Contents