Related Manuals for Idex Corken Coro-Vac CPS1X
Summary of Contents for Idex Corken Coro-Vac CPS1X
- Page 1 IG100 IMPORT ANT INSTRUCTIONS OILLESS SERIES CORO-VAC MODEL CYLINDER/TANK PURGING SYSTEMS CPS1V CPS6R CPS4V...
- Page 2 This is the hazard alert symbol: When you see this symbol, be aware that personal injury or property damage is possible. The hazard is explained in the text following the symbol. Read the information carefully before proceeding. The following is an explanation of the three different types of hazards: DANGER Severe personal injury or death will occur if hazard is ignored.
- Page 3 ATMOSPHERIC PRESSURE BY ALTITUDE FOR CYLINDER PURGING Altitude Above Atmospheric Barometer Gauge Reading Gauge Reading Reference City Sea Level (ft) Pressure (psia) Reading (in. Hg) at 2 psia at 5 psia Boston, PA 14.69 29.92 25.85 19.74 14.43 29.38 25.31 19.20 1000 14.17...
-
Page 4: General Information
GENERAL INFORMATION INSTALLATION WARNING To This pump is only to be used for the purpose avoid risk of pumping air and under no circumstances electrocution do not use be used with any other gases. The pump this product in an area must not be used for the pumping of fluids, where it could come in particles, solids or any substance mixed... -
Page 5: Grounding Instructions
and gauges at the inlet or outlet, or both, GROUNDED, CORD- to monitor performance. Check valves CONNECTED PRODUCTS: This product required prevent should be grounded. In the event of an backstreaming through the pump. electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. -
Page 6: Electric Motor Connection
EXTENSION CORDS: WARNING Pump surfaces can become Use only a 3-wire extension cord that has very hot during operation. a 3-blade grounding plug, and a 3-slot Do not touch these surfaces receptacle that will accept the plug on the until unit has been shut off product, Make sure your extension cord and allowed to cool. - Page 7 Refer to exploded view drawing during use any chlorinated solvents to clean the following procedure. valves, or any liquids to flush units, THE STAINLESS STEEL VALVES MAY BE Make sure the pump is turned off, isolated CLEANED WITH WATER. All parts, from the power supply, and that all pressure except the valves, can be cleaned with and/or vacuum is released from the pump.
- Page 8 • Position manifold and tighten Manifold Install and tighten the pump body nut 1/2 to 3/4 turns beyond hand tight. bolts. Install the belleville springs with the washer between them, and • Retorque head screws again after the snap ring. running for 10 minutes.
-
Page 9: Troubleshooting Guide
TROUBLESHOOTING GUIDE Vacuum Motor Excessive Won’t Possible Reason High Overheating Overload Noise Start Dirty Filter at pump Dirty Muffler Plugged Vacuum Line at pump Vanes Sticking Running at Too High RPM Rings / Vanes Worn Shaft Seal Worn (Replace) Particulate Material in Pump Motor Not Wired Correctly Damaged / Dirty Valves Improper Cylinder Alignment... - Page 10 CPS1V, CPS1X EXPLODED VIEW AND PARTS ORDERING INFORMATION DESCRIPTION QTY. Muffler Assembly • 2 Felt Inline Filter (not shown) Cylinder Head • 5 Head Gasket • 6 Valve, Outlet Valve Plate • 8 Valve, Inlet • 9 Cylinder Gasket Cylinder •...
- Page 11 CPS4V AND CPS4X EXPLODED VIEW AND PARTS ORDERING INFORMATION DESCRIPTION QTY. Muffler Assembly • 2 Felt Inline Filter (not shown) Cylinder Head • 5 Head Gasket • 6 Valve, Outlet Valve Plate • 8 Valve, Inlet • 9 Cylinder Gasket Cylinder •...
- Page 12 CPS6R EXPLODED VIEW AND PARTS ORDERING INFORMATION DESCRIPTION QTY. DESCRIPTION QTY. Body Fan Guard Rotor Assembly Intake Filter Assembly • 3 Vane Gasket • 4 Body Gasket Foot Bracket Filter Assembly • 6 Deflector • 21 Cartridge • 7 Ball Bearing (Drive & Dead) •...