Configuration Settings - Maytag Amana PTC A Series Service Instructions Manual

PROPER INSTALLATION
Feature Code
---
Start Configuration position
C1
Interface Usage
C2 Fan Operation
C3 Reverse Cycle Operation
C4
Room Identification first two digits
C5
Room Identification last two digits
C6 Wired Occupancy
C7 Wired Motion Sensor Type
C8 Cooling Temperature Limiting
C9 Heating Temperature Limiting
C0 Reverse Cycle "B" or "O"
selection for thermostat
c2 Wired Unrented Set Back
c3 Unrented Cooling Temperature
c4 Unrented Heating Temperature
Cb Dehumidification
CC Dehumidistat call for a drop in temperature
Cd English/Metric Temperature
CE Freeze Protection
CF Hi. Speed Cooling Smart Temperature
CH Hi Speed Heating Smart Temperature
CJ 2nd Stage Heat. Dif.
d1 Room Air Mix Cooling
d2 Room Air Mix Heating
d3 Air Mix Fan Speed
d4 Heating Smart Speed
d5 Warnings,
OCT Lock & LED
d6 Sensorless Un-Occ. Time and Fan Revert Time
d7 1st Un-Occ. Set Back Temperature
d8 1st Un-Occ. Set Back Time
d9 2nd Un-Occ. Set Back Temperature
dA 2nd Un-Occ. Set Back Time
dB 3rd Un-Occ. Set Back Temperature
dC 3rd Un-Occ. Set Back Time
dH Electric Heater Size
r4 Room Prefix
r5 Room Suffix
*Indicates factory default.
32
Description Option Code

CONFIGURATION SETTINGS

Unit is only controlled by the PTAC touchpad.
0*
rE Unit is both controlled by a wireless thermostat and/or the touchpad.
L5 Unit is controlled by a wired thermostat via the low voltage terminals only.
The fan only runs with the call for heating or cooling.
Au*
The fan runs continuously except in the OFF position.
On
The fan runs continuously in cooling and cycles with call for heating.
C
Unit is equipped with fan operation button for guest selection of fan cycling.
bP
Unit is equipped with fan operation button, but self reverts to cyclic fan.
bA
Unit is equipped with fan operation button, but self reverts to continuous fan.
bC
The fan always runs even in OFF mode
A
Cooler only with or without electric heat.
C
Heat Pump.
H*
Service no Operation "Eo"
0
Set first two digits of room identification
00-99
Set last two digits of room identification
00-99
"No Occupancy" detection devices
0*
Wired Door Switch and Motion Sensor present
1
18 Enter "No Occupancy" routine 18 hours after last control selection
Normally Closed Device (Open when sensing motion)
0*
Normally Open Device (Closed when sensing motion)
1
Select temperature between 60 and 72 for minimum cooling set point
60*-72
Select temperature between 68 and 90 for maximum heating set point
68-90, 80*
Mating thermostat has a "B" terminal
8*
Mating thermostat has an "O" terminal
0
Not Active
0*
Active
A
Select temperature between 45 and 95 minimum unrented cooling set point.
45-95, 79*
Select temperature between 45 and 95 minimum unrented heating set point.
45-95, 63*
Not Active
0*
Active
1
Active in No occupancy / Unrented State
U
3-8
3-8
Fahrenheit Scale
F*
Celsius Scale
C
On, low fan*
L*
On, high fan
H
Off
0
5-9
5*-9
6-8
6-8*
4-8
4*-8
No electric heat
--
On
1*
Off
0
Off
0*
On
1
Low
L*
High
H
Not Available
0
Available
1*
Enabled
1*
Dis-enabled
0
1- 32, 18*
1-32
1-16, 2*
1-16
.1, .5, 1-24, .5*
.1, .5, 1-24
1-16, 3*
1-16
.1, .5, 1-24 (d8)-24, 1*
1-16, 6*
1-16
(dA)-24, 3*
.1, .5, 1-24
00*, 15, 20,
00*, 15, 20, 25, 35 & 50
25, 35, 50
00* - 99
00* - 99
00* - 99
00* - 99
Description