Maintenance - AEG PL 750 Original Instructions Manual

Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
TECHNICAL DATA
Sound pressure level (K = 3 dB(A)) ..................................86 dB (A)
Sound power level (K = 3 dB(A)) .....................................97 dB (A)
PL 750
Wear ear protectors!
Rated input ...................................................................750 W
No-load speed ...........................................................17000 min
Total vibration values (vector sum in the three axes)
Planing width ..................................................................82 mm
determined according to EN 60745.
Planing depth .............................................................0-2,0 mm
Vibration emission value a
Rabbet depth................................................................0-11 mm
Uncertainty K=...............................................................1,5 m/s
Weight without cable .....................................................2,9 kg
GB
Noise/vibration information
WARNING!
Measured values determined according to EN 60 745.
The vibration emission level given in this information sheet has been
Typically, the A-weighted noise levels of the tool are:
measured in accordance with a standardised test given in EN 60745
Sound pressure level (K = 3 dB(A)) ..................................86 dB (A)
and may be used to compare one tool with another. It may be used
Sound power level (K = 3 dB(A)) .....................................97 dB (A)
for a preliminary assessment of exposure.
Wear ear protectors!
The declared vibration emission level represents the main
Total vibration values (vector sum in the three axes)
applications of the tool. However if the tool is used for diff erent
determined according to EN 60745.
applications, with diff erent accessories or poorly maintained, the
Vibration emission value a
vibration emission may diff er. This may signi� cantly increase the
Uncertainty K=...............................................................1,5 m/s
exposure level over the total working period.
GB
An estimation of the level of exposure to vibration should also take
into account the times when the tool is switched off or when it is
WARNING!
running but not actually doing the job. This may signi� cantly reduce
The vibration emission level given in this information sheet has been
the exposure level over the total working period.
measured in accordance with a standardised test given in EN 60745
Identify additional safety measures to protect the operator from the
and may be used to compare one tool with another. It may be used
eff ects of vibration such as: maintain the tool and the accessories,
for a preliminary assessment of exposure.
keep the hands warm, organisation of work patterns.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for diff erent
WARNING! Read all safety warnings and all
applications, with diff erent accessories or poorly maintained, the
instructions, including those given in the accompanying
vibration emission may diff er. This may signi� cantly increase the
brochure. Failure to follow the warnings and instructions may result
exposure level over the total working period.
in electric shock, � re and/or serious injury.
An estimation of the level of exposure to vibration should also take
Save all warnings and instructions for future reference.
into account the times when the tool is switched off or when it is
running but not actually doing the job. This may signi� cantly reduce SAFETY INSTRUCTIONS
the exposure level over the total working period.
Wear ear protectors. Exposure to noise can cause hearing loss.
Identify additional safety measures to protect the operator from the
Wait for the cutter to stop before setting the tool down. An
eff ects of vibration such as: maintain the tool and the accessories,
exposed rotating cutter may engage the surface leading to possible
keep the hands warm, organisation of work patterns.
loss of control and serious injury.
Hold power tool by insulated gripping surfaces only, because
WARNING! Read all safety warnings and all
the cutter may contact its own cord. Cutting a „live" wire may
instructions, including those given in the accompanying
make exposed metal parts of the power tool „live" and shock the
brochure. Failure to follow the warnings and instructions may result
operator.
in electric shock, � re and/or serious injury.
Use clamps or another practical way to secure and support
Save all warnings and instructions for future reference.
the workpiece to a stable platform. Holding the work by your
hand or against the body leaves it unstable and may lead to loss of
SAFETY INSTRUCTIONS
control.
Wear ear protectors. Exposure to noise can cause hearing loss.
Wait for the cutter to stop before setting the tool down. An
English
exposed rotating cutter may engage the surface leading to possible
loss of control and serious injury.
8 Hold power tool by insulated gripping surfaces only, because
the cutter may contact its own cord. Cutting a „live" wire may
make exposed metal parts of the power tool „live" and shock the
operator.
Use clamps or another practical way to secure and support
the workpiece to a stable platform. Holding the work by your
hand or against the body leaves it unstable and may lead to loss of
control.
English
10
8
.............................................3,0 m/s
h
.............................................3,0 m/s
h
rendered ineff ective. Use adhesive labels.
Always disconnect the plug from the socket before carrying out any
work on the machine.
Appliances used at many diff erent locations including open air should
Planer
Keep mains lead clear from working range of the machine. Always
be connected via a residual current device
lead the cable away behind you.
(FI, RCD, PRCD) of 30mA or less.
Only plane with sharp blades and avoid metal (nails, screws).
Always use the protective shields on the machine.
-1 Never reach into the danger area of the planer when it is running.
Always wear goggles when using the machine. It is recommended to
wear gloves, sturdy non slipping shoes and apron.
The dust produced when using this tool may be harmful to health (e.g.
when working oak or beech wood, stones, paint, which could contain
Sawdust and splinters must not be removed while the machine is
2
lead or other harmful chemicals). Do not inhale the dust. Use a dust
running.
2
absorption system and wear a suitable dust protection mask. Remove
Do not drill the housing, as the protective insulation would be
deposited dust thoroughly, e.g. with a vacuum cleaner.
rendered ineff ective. Use adhesive labels.
Always disconnect the plug from the socket before carrying out any SPECIFIED CONDITIONS OF USE
work on the machine.
The planer can plane surfaces and rabetts, and bevel and chamfer
Keep mains lead clear from working range of the machine. Always
edges.
lead the cable away behind you.
Do not use this product in any other way as stated for normal use.
Only plane with sharp blades and avoid metal (nails, screws).
ADVICE FOR OPERATION
Never reach into the danger area of the planer when it is running.
The dust produced when using this tool may be harmful to health (e.g.
Never reach into the danger area of the planer when it is running.
when working oak or beech wood, stones, paint, which could contain
2
Place the front page of the machine on to the worpiece and switch
lead or other harmful chemicals). Do not inhale the dust. Use a dust
2
on, before the planer blade touches the workpiece and then guide
absorption system and wear a suitable dust protection mask. Remove
evenly over the workpiece.
deposited dust thoroughly, e.g. with a vacuum cleaner.
The v-shape notch in the front of the supporting plate ensures safe
SPECIFIED CONDITIONS OF USE
chamfering of edges.
The planer can plane surfaces and rabetts, and bevel and chamfer
ECDECLARATION OF CONFORMITY
edges.
We declare under our sole responsibility that this product is in Do not use this product in any other way as stated for normal use.
conformity with the following standards or standardized documents.
ADVICE FOR OPERATION
EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, in
accordance with the regulations 2006/42/EC, 2004/108/EC
Never reach into the danger area of the planer when it is running.
Place the front page of the machine on to the worpiece and switch
on, before the planer blade touches the workpiece and then guide
evenly over the workpiece.
Winnenden, 2010-31-03 The v-shape notch in the front of the supporting plate ensures safe
chamfering of edges.
MAINS CONNECTION ECDECLARATION OF CONFORMITY
Connect only to single-phase AC current and only to the system
We declare under our sole responsibility that this product is in
voltage indicated on the rating plate. It is also possible to connect
conformity with the following standards or standardized documents.
to sockets without an earthing contact as the design conforms to
EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, in
safety class II.
accordance with the regulations 2006/42/EC, 2004/108/EC

MAINTENANCE

The ventilation slots of the machine must be kept clear at all times.
Winnenden, 2010-31-03
In order to guarantee constant readiness for operation, the machine
should be checked for worn carbon brushes at one of the AEG
aftersales service agencies.
MAINS CONNECTION
Use only AEG accessories and spare parts. Should components need to
Connect only to single-phase AC current and only to the system be replaced which have not been described, please contact one of our
voltage indicated on the rating plate. It is also possible to connect
service agents (see our list of guarantee/service addresses).
to sockets without an earthing contact as the design conforms to
If needed, an exploded view of the tool can be ordered. Please state
safety class II.
the Article No. as well as the machine type printed on the label
and order the drawing at your local service agents or directly at:
AEG Elektrowerkzeuge, Max-Eyth-Straße 10, D-71364 Winnenden,
Germany.
SYMBOLS
Please read the instructions carefully before
starting the machine.
10
Always disconnect the plug from the socket
before carrying out any work on the machine.
Rainer Kumpf
Manager Product Development
Authorized to compile the technical � le
Rainer Kumpf
Manager Product Development
Authorized to compile the technical � le