Advertisement
TROUBLESHOOTING
The error messages listed in the following table cause the 6162RF to produce a single ding tone. Table 5 describes the error
messages and the corrective actions.
Table 5 – Troubleshooting
Display
Open Ckt
No data is being received from the control panel.
1. The control panel does not see the 6162RF
Check 100 RF
Receiver, or the Receiver is not functioning.
Receiver
Check 8xx*
2. Another device on the keypad terminals is
*xx= the device
conflicting with this receiver address.
address of the
receiver.
FUNCTION KEY LABELS
A set of adhesive-backed labels with some typical function
symbols (fire, police, personal emergency) is provided. These
labels can be placed next to the keys to identify each key's
function for the end user (as determined by the control panel's
capability and programming; see the control's instructions).
PANIC ALARM STICKERS
800-13067-02
FEDERAL COMMUNICATIONS COMMISSION STATEMENT:
The user shall not make any changes or modifications to the equipment unless authorized by the
Installation Instructions or User Manual. Unauthorized changes or modifications could void the
user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The
FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly,
that is, in strict accordance with the manufacturer's instructions, may cause interference to radio
and television reception. It has been type tested and found to comply with the limits for a Class B
computing device in accordance with the specifications in Part 15 of FCC Rules, which are
designed to provide reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on
different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
REFER TO INSTALLATION INSTRUCTIONS FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND
LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
WARRANTY INFORMATION: For the latest warranty information, please go to www.honeywell.com/security/hsc/resources/wa
DOCUMENTATION AND ONLINE SUPPORT: For the latest documentation and online support information, please go to:
Probable Cause
61x2-FUNCT-KEY-LBLS-07-19-13
http://www.security.honeywell.com/hsc/resources/MyWebTech
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2013 Honeywell International Inc.
www.honeywell.com/security
Corrective Action
Verify that the Yellow keypad wire is connected properly.
1a. Verify that the Yellow and Green keypad wires are
connected properly.
1b. Verify that the receiver address is set for 00.
2. Verify the address of all devices on the keypad bus.
SPECIFICATIONS
Physical:
4.88"H x 6.934"W x 1.02"D
Displays:
4 x 16 alpha-numeric supertwist LCD, backlit.
Sounder:
Speaker [fire alarm is loud, pulsing single tone;
(all Keypads) burglary alarm is loud, continuous,
dual tone].
Voltage:
12VDC (power-limited)
Current:
210mA (ARMED LED lit, LCD backlight and
sounder on), reduces to 120mA when panel is
operating in standby mode (backlight off).
NFPA-72: Compliant.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
FCC / IC STATEMENT:
This device complies with Part 15 of the FCC
Rules, and RSS 210 of Industry Canada (IC).
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference (2) This device must accept
any interference received, including interference
that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles
de la FCC & de RSS 210 des Industries Canada.
Son fonctionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer
d'interférences nuisibles. (2) Cet appareil doit
accepter toute interférence reçue y compris les
interférences causant une réception indésirable.
Ê800-11508V11Š
800-11508V1 7/13 Rev A
Advertisement
