Cisco IR1101 Getting Started
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. IR1101
  6. Getting started
Cisco IR1101 Getting Started

Cisco IR1101 Getting Started

Industrial integrated services router
Hide thumbs Also See for IR1101:
Table of Contents

Advertisement

Quick Links

Getting Started and Product Document of
Compliance for the Cisco IR1101 Industrial
Integrated Services Router
I
MPORTANT
Cisco Part Number 78-101332-01A0
Introduction, page 1

Introduction

The purpose of this document is to provide the installer the necessary information for installing the Cisco IR1101
Industrial Integrated Services Router. The documentation is on-line, and subject to change. Make sure that you are
downloading or viewing on-line the latest version before beginning an installation.
This document also contains Product Compliance and Safety information as well as Declaration of Conformity.

Items Shipped with your Router

Unpack the box and verify that all items listed on the invoice were shipped with the Cisco IR1101.
! R
A
EAD
B
I
EFORE
NSTALLING THE
Cisco Systems, Inc.
S
LL THE
AFETY
H
ARDWARE
www.cisco.com
1
I
NFORMATION

Advertisement

Table of Contents
loading

Related Manuals for Cisco IR1101

Summary of Contents for Cisco IR1101

  • Page 1: Table Of Contents

    Declaration of Conformity with regard to the R&TTE Directive 2014/53/EU & Medical Directive 93/42/EEC, page 16 Introduction The purpose of this document is to provide the installer the necessary information for installing the Cisco IR1101 Industrial Integrated Services Router. The documentation is on-line, and subject to change. Make sure that you are downloading or viewing on-line the latest version before beginning an installation.

  • Page 2: Equipment That You Supply

    Ratcheting torque screwdriver that exerts up to 15 in-lb (1.69 N-m) of pressure. Related Documentation To access resources or to display the latest Cisco 1101 Series Router documentation on-line, go to this URL: https://www.cisco.com/c/en/us/support/routers/1101-industrial-integrated-services-router/model.html This portal has all of the information you need to get to know your router, install and configure it, as well as access software.
  • Page 3 Getting Started and Product Document of Compliance for the Cisco IR1101 Industrial Integrated Services Router Warning: Explosion Hazard - The area must be known to be nonhazardous before installing, servicing, or replacing the unit. Statement 1082 Warning: In order to comply with FCC radio frequency (RF) exposure limits, antennas for this product should be located a minimum of 11.8 in.

  • Page 4: Grounding The Router

    Getting Started and Product Document of Compliance for the Cisco IR1101 Industrial Integrated Services Router Grounding the Router Make sure to follow any grounding requirements at your site. The ground lug is supplied with the device. Warning: This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor.

  • Page 5: Connecting Dc Power

    IEC 60950 based safety standards. Statement 1033 Plugs and Pin-Outs The following is a brief overview of connecting to DC power. Details can be found in the Cisco IR1101 Industrial Integrated Services Router Hardware Installation Guide and should be understood before beginning. See...
  • Page 6 Getting Started and Product Document of Compliance for the Cisco IR1101 Industrial Integrated Services Router Figure 1 Power Connector Pin-outs Table 1 Power connector Descriptions Pin Number Name Description Color DC In + DC Power Positive Input DC In -...

  • Page 7: Connecting To The Router Gateway Ports

    Getting Started and Product Document of Compliance for the Cisco IR1101 Industrial Integrated Services Router Using an 18-gauge wire-stripping tool, strip each of the two twisted pair wires coming from each DC-input power source to 0.25 inch (6.3 mm) ± 0.02 inch (0.5 mm). Do not strip more than 0.27 inch (6.8 mm) of insulation from the wire.

  • Page 8: Installing A Pluggable Module

    Getting Started and Product Document of Compliance for the Cisco IR1101 Industrial Integrated Services Router Installing a Pluggable Module For hazardous location environments, follow these warnings when installing a pluggable module. Warning: Explosion Hazard - The area must be known to be nonhazardous before installing, servicing, or replacing the unit.
  • Page 9 Getting Started and Product Document of Compliance for the Cisco IR1101 Industrial Integrated Services Router Figure 4 Sim Installation Item Description Micro SIMs SIM 0 (towards the device) SIM 1 (away from the device) Push in each SIM until it clicks into place. When the SIMs are installed, re-attach the access plate previously removed with a screwdriver.
  • Page 10 Getting Started and Product Document of Compliance for the Cisco IR1101 Industrial Integrated Services Router Figure 5 USB Port Cover Installation Tighten the latch lock screw to a torque of 2.8 to 3.8 inch-lbs (0.3 to 0.4 newton meter). Refer to...
  • Page 11 Getting Started and Product Document of Compliance for the Cisco IR1101 Industrial Integrated Services Router Figure 7 Pluggable Module Insert Attach your antennas to the ports on the pluggable module. There are different instructions for each antenna type, be sure to consult the antenna documentation for proper orientation and torque to install them.

  • Page 12: Emc Information

    Getting Started and Product Document of Compliance for the Cisco IR1101 Industrial Integrated Services Router Hazardous Locations Standards and Marking Strings The following standards were used for the hazardous locations approvals and certifications: UL 121201, Ed. 9 CAN/CSA C22.2 No. 60079-0-11 Ed. 2 CAN/CSA C22.2 No.
  • Page 13 This device must accept any interference received, including interference that may cause undesired operation. Cisco® IR1101 Industrial Integrated Services Routers are certified to the requirements of RSS-210. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations.
  • Page 14 This Device Meets International Guidelines for Exposure to Radio Waves The IR1101 series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) recommended by international guidelines. The guidelines were developed by an independent scientific organization (ICNIRP) and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health.
  • Page 15 This Device Meets FCC Guidelines for Exposure to Radio Waves The IR1101 series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in FCC Part 1.1310. The guidelines are based on IEEE ANSI C 95.1 (92) and include a substantial safety margin designed to ensure the safety of all persons, regardless...

  • Page 16: Declaration Of Conformity With Regard To The R&Tte Directive 2014/53/Eu & Medical Directive 93/42/Eec

    This declaration is only valid for configurations (combinations of software, firmware and hardware) provided and/or supported by Cisco Systems for use within the EU or countries that have implemented the EU Directives. The use of software or firmware not supported/provided by Cisco Systems may result that the equipment is no longer compliant with the regulatory requirements.
  • Page 17 Getting Started and Product Document of Compliance for the Cisco IR1101 Industrial Integrated Services Router Table 2 Country Statements Deutsch [German]: Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU. Eesti [Estonian]: See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.
  • Page 18 Safety: EN 60950-1 CE Mark For the Cisco IR1101-K9, the following CE mark is affixed to the equipment and its packaging: National Restrictions In the EU and other European Countries, the 2.4GHz and 5GHz bands have been made available for the use of wireless LANs.
  • Page 19 (external) antennas available from Cisco. The following link to the data sheet lists the antennas that can be used by IR1101. All antennas where assessed together with the equipment against the requirements of the R&TTE directive.
  • Page 20 Cisco at complianceinfo@cisco.com. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners.

Table of Contents