Possible Display Messages; To Install The Wheels Onto The Dolly; Models With Power Packs; Models With Ridgid/Kollmann Seesnake Provided Monitor Vcrs - RIDGID Color SeeSnake KD-200 Color Operator's Manual

Kollmann
to be individually reentered. The battery should last
for approximately 5 years.
4. Before inserting a new CR-2032 battery, make
sure the polarity is correct. Insert the battery such
that the +(plus) side of the battery is towards the
top of the battery holder (this is also towards the
center of the CountIR).

Possible Display Messages

Error 1: Displayed when the CountIR reads a dis-
tance which is out of bounds. These
boundaries could be less than zero or a
length that is 40 feet greater than what the
system is configured for.
Error 2: Displayed when the system memory is not
set up. This can occur when the battery
needs to be replaced.
No Video: Displayed when the camera is disconnect-
ed. Once the camera is reconnected, the
screen is restored.

To Install the Wheels Onto the Dolly

NOTE! The rims of the wheels are flat on one side, con-
vex on the other. To make the wheel stance as
wide as possible (more stable), the flat edge
should face outward when the wheels are
mounted.
1. Position the axle so that the side with the rubber
foot is on the same side as the other two rubber
feet on the dolly frame. Slide one wheel onto the
axle with the flat edge facing outward.
2. Slide the axle and wheel through one frame mount
(on the side with the rubber feet), then through the
plastic spacer. Slide the axle through the other
frame mount.
3. Slide the second wheel onto the axle with the flat
edge facing outward. Slide the washer onto the
axle (outboard of the wheel); then insert the cotter
pin at the far end of the axle.

Models with Power Packs

1. Find the power button at the front of the power
pack, and make sure it is switched OFF. Plug the
power pack's power cord into an approved outlet,
and press GFCI reset switch.
2. Unwrap the interconnect cable from its storage
hooks on the dolly. Plug the loose end of this cord
into the mating connector on the power pack, refer-
ring to Figures 1 and 8.
SeeSnake ™ Diagnostic Equipment
Ridge Tool Company • Elyria, Ohio • U.S.A.
NOTE! Figure 1 demonstrates the proper way to plug
connectors together. This is true in all cases.
For example, the camera head will plug directly
into the back of the monitor/power pack, using
these guidelines.
3. Locate the small video cable that came with the
power pack. Plug either end of it into the small jack
on the power pack labeled video out. (These types
of connectors are called RCA jacks.) Most likely,
your monitor will have the same type of connector
for video in. (If not, it has a connector called a
BNC jack.)
4. Plug the remaining end of the video cable into the
monitor at the video in jack.
5. Turn the monitor ON, then the power pack. You
should now have a picture on the screen. If the pic-
ture doesn't look perfect, you can adjust the con-
trast, brightness, and horizontal/vertical hold on
your monitor, as well as the brightness of the cam-
era head LED lighting using the dimmer knob locat-
ed on the front of the power pack.
NOTE! If you do not have a picture, make sure you have
followed the above steps correctly, checking to
see that the video cable is plugged in and the
120V source is actually working.
Models with RIDGID/Kollmann
SeeSnake Provided Monitor
NOTE! Please refer to Monitor
plete details.
1. Gather the reel/dolly and Monitor
nient area near a 120V or 230V AC power source.
2. Lift and open the black sunshade that covers the
screen of the Monitor +
NOTE! Figure 1 demonstrates the proper way to plug
connectors together. This is true in all cases.
For example, the camera head will plug directly
into the back of the monitor/power pack, using
these guidelines.
3. Unwrap the interconnect cord from its hooks located
on the back side of the dolly. Plug this cord into the
connector at the front of the monitor, referring to
Figure 1 for the proper way to make the connection.
4. Plug the power cord for the monitor into a standard
120 or 230 volt outlet.
5. Locate the power button at the lower-left, front of
the Monitor + VCR and depress it. In a few moments
you should have a picture. You may need to adjust
the brightness and contrast of the monitor. This can
be accomplished by adjusting the dials to the right
of the power button. The one represented by a sun
above it is the brightness, and the one with the par-
+ VCRs
+ VCR manual for com-
+ VCR in a conve-
VCR.
9