Table of Contents
Advertisement
Lyric Gateway Installation and Reference Guide
Testing the System
Testing the Sy
stem
Testing the Sy
Testing the Sy
stem
stem
Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are
vital to continuous satisfactory operation of any alarm system.
The installer should assume the responsibility of developing and offering a regular maintenance program to
the user as well as acquainting the user with the proper operation and limitations of the alarm system and its
component parts. Recommendations must be included for a specific program of frequent testing (at least
weekly) to ensure the system's proper operation at all times.
Test Modes
Test Modes
Test Modes
Test Modes
The following tests are available to the Installer via the AlarmNet 360 app when the "Advanced" icon is selected
from the Installer Tools screen:
Option
Option
Option
Option
System Information
Comm. Test
The following tests are available to the Installer via the Gateway touchpad.
Option
Option
Option
Option
Go-No-Go Test
The following tests are available to the Installer via the MyHome Gateway app when the "Advanced" icon is
selected from the Master User screen:
Option
Option
Option
Option
Walk Test
Testing the System
Testing the System
Testing the System
Testing the System
After installation is completed, the security system should be carefully tested, as follows:
Step
Step
Step
Step
1.
With the system in the disarmed state, check that all zones are intact. If the Status Shield is not lit
green, select the "Security" icon on the Smart Device followed by the "Zones" icon to display the
faulted zone(s). If necessary, restore faulted zone(s) so that the "Home" button lights. Fault and
restore every sensor individually to assure that it is being monitored by the system.
Alarm Reporting (Armed System
Alarm Reporting (
Alarm Reporting (
Alarm Reporting (
Armed System
Armed System
Armed System) ) ) ) Test
Alarm messages will be sent to the Central Station during the following steps 1 and 2. Notify the Central Station
in advance that tests will be in progress.
Step
Step
Step
Step
1.
Arm the system and fault one or more zones. Silence alarm sounder(s) and disarm the system by
selecting "Disarmed" and entering the Security Code. Check entry/exit delay zones.
2.
Check the touchpad-initiated alarms that are in the system by selecting "Emergency" followed by
applicable Panic keys. If the system has been programmed for audible emergency, the touchpad will
emit a steady alarm sound, and "Alert" will flash red. In addition, "ALARM" and zone number will be
displayed on Smart Device. Silence the alarm by selecting "Disarmed" and entering the Security
Code. If the system has been programmed for silent emergency, there will be no audible alarms or
displays, but a report will be sent to the Central Station.
3.
Notify the Central Station when all tests are finished, and verify results with them.
4.
To test the wireless part of the system and the RF receiver, perform the Go-No-Go Test.
N N N N OTE
OTE
OTE
OTE: : : : Go/No Go Test will be automatically terminated after 3-1/2 to 4 hours if the installer or user does not
manually terminate it. This ensures that fire and panic zones will not remain disabled. During the final 5
minutes the system will emit double beeps indicating that the end of Test mode is nearing.
TO THE INSTALLER
TO THE INSTALLER
TO THE INSTALLER
TO THE INSTALLER
System Information is displayed. Select OK to return to the previous screen.
The Communications Test mode performs network diagnostics and sends test alarms
to AlarmNet 360. Dependent upon the type of Communications device that is used,
the following tests are available:
• Test Ethernet/Wi-Fi
• Test IP
• Send Any
• Send Cellular Message
• Send Ethernet Message
The results for the selected test will be displayed.
Used to verify adequate RF signal strength from proposed transmitter locations.
The Walk Test mode allows each protection point to be checked for proper
operation. Refer to the Lyric Gateway User Manual for additional information.
Test (via AlarmNet 360)
Test
Test
(via AlarmNet 360)
(via AlarmNet 360)
(via AlarmNet 360)
Function
Function
Function
Function
Function
Function
Function
Function
Function
Function
Function
Function
Action
Action
Action
Action
Action
Action
Action
Action
- 26 -
Advertisement
Table of Contents
