Page 1
K-60SP Drain Cleaning Machine OPERATOR’S MANUAL • Français – 15 • Castellano – pág. 31 WARNING! Read this Operator’s Manual carefully before using this tool. Failure to understand and follow the contents of this manual may result in electri- cal shock, fire and/or serious personal injury.
Page 2
K-60SP Drain Cleaning Machine Table of Contents Recording Form for Machine Serial Number ......................1 General Safety Information Work Area Safety ................................2 Electrical Safety................................2 Personal Safety ................................2 Tool Use and Care ..............................3 Service ..................................3 Specific Safety Information Drain Cleaner Safety ..............................3 Description, Specifications and Standard Equipment Description ..................................4 Specifications ................................4...
Page 3
K-60SP Drain Cleaning Machine K-60SP Drain Cleaning Machine Record Serial Number below and retain product serial number which is located on nameplate. Serial 1.800.561.8187 information@itm.com www. .com...
K-60SP Drain Cleaning Machine General Safety Information are rated for outdoor use and reduce the risk of elec- trical shock. WARNING! Read and understand all instructions. Failure to follow all instructions listed below may • Use only three-wire extension cords which have result in electric shock, fire, and/or serious three-prong grounding plugs and three-pole re- personal injury.
K-60SP Drain Cleaning Machine Specific Safety Information • Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables bet- ter control of the tool in unexpected situations. WARNING Read this operator’s manual carefully before using •...
K-60SP Drain Cleaning Machine Machine Inspection 6. Use tools and accessories that are designed for your drain cleaner and meet the needs of your application. The correct tools and accessories allow you to do the WARNING job successfully and safely. Accessories suitable for use with other equipment may be hazardous when used with this drain cleaner.
Page 8
K-60SP Drain Cleaning Machine pin key removed, handle should be in its upper-most WARNING Never couple more than one cable at a position. time. Cable will extend behind rear guide tube. NOTE! Adjust the jaw set as required. The K-60SP NOTE! When not in use, the clutch handle should be in has a jaw set adjustment which allows the ma- its locked (down) position in order to protect...
K-60SP Drain Cleaning Machine 2. Pull sufficient cable out of the machine to start tool and Operating Instructions cable into the sewer inlet. If going through a “P” trap, push cable into inlet as far as it will go. WARNING 3.
K-60SP Drain Cleaning Machine Special Procedures 10. To add cable, the following procedure should be fol- lowed: Reverse Operation • After reaching the end of each cable section, turn Running machine in reverse will cause premature fail- the machine OFF. ure of cable.
• If the jaw set does not engage the cable when the – A-8 Cable Carrier clutch handle is pressed, the jaw set is open too 61625 A-61 Standard Equipment Tool Kit for K-60SP-SE includes: wide. – T-101 Straight Auger – T-102 Funnel Auger •...
K-60SP Drain Cleaning Machine Figure 11 – Remove Socket Head Cap Screws 2. Remove the jaw housing. The clutch jaw assembly is contained in the jaw housing. Figure 12 – Remove Jaw Set Cover 3. Remove the jaw set cover by rotating counter-clock- wise (Figure 12).
RIDGID service technician. NOTE! Do not tighten this set screw by driving it into the Tool should be taken to a RIDGID Independent Auth- motor. orized Service Center or returned to the factory. All repairs 7. While holding the set screw in place with the ″...
K-60SP Drain Cleaning Machine Wiring Diagram 115V/60 Hz Service Cord 1 Black 3 Blue White 7 Red Black Motor Green 4 White 2 Brown 230V/50 Hz Service Cord 1 Black 3 Blue Blue 7 Red Motor Brown Grn/Yel 4 White 2 Brown Green 1.800.561.8187...
Page 16
No other express warranty applies This FULL LIFETIME WARRANTY is the sole and exclusive warranty for RIDGID ® products. No employee, agent, dealer, or other person is authorized to alter this warranty or make any other warranty on behalf of the RIDGE TOOL COMPANY.