Configure Static Routes For The Management Interface - Dell S3048-ON Configuration Manual

• tag tag-value: the range is from 1 to 4294967295. (optional)
Example of the show ip route static Command
To view the configured routes, use the show ip route static command.
Dell#show ip route static
Destination Gateway
----------- -------
S 2.1.2.0/24 Direct, Nu 0
S 6.1.2.0/24 via 6.1.20.2, Gi 5/1
S 6.1.2.2/32 via 6.1.20.2, Gi 5/1
S 6.1.2.3/32 via 6.1.20.2, Gi 5/1
S 6.1.2.4/32 via 6.1.20.2, Gi 5/1
S 6.1.2.5/32 via 6.1.20.2, Gi 5/1
S 6.1.2.6/32 via 6.1.20.2, Gi 5/1
S 6.1.2.7/32 via 6.1.20.2, Gi 5/1
S 6.1.2.8/32 via 6.1.20.2, Gi 5/1
S 6.1.2.9/32 via 6.1.20.2, Gi 5/1
S 6.1.2.10/32 via 6.1.20.2, Gi 5/1
S 6.1.2.11/32 via 6.1.20.2, Gi 5/1
S 6.1.2.12/32 via 6.1.20.2, Gi 5/1
S 6.1.2.13/32 via 6.1.20.2, Gi 5/1
S 6.1.2.14/32 via 6.1.20.2, Gi 5/1
S 6.1.2.15/32 via 6.1.20.2, Gi 5/1
S 6.1.2.16/32 via 6.1.20.2, Gi 5/1
S 6.1.2.17/32 via 6.1.20.2, Gi 5/1
S 11.1.1.0/24 Direct, Nu 0
Direct, Lo 0
--More--
Dell Networking OS installs a next hop that is on the directly connected subnet of current IP address on the interface.
Dell Networking OS also installs a next hop that is not on the directly connected subnet but which recursively resolves to a next hop on the
interface's configured subnet.
• When the interface goes down, Dell Networking OS withdraws the route.
• When the interface comes up, Dell Networking OS re-installs the route.
• When the recursive resolution is "broken," Dell Networking OS withdraws the route.
• When the recursive resolution is satisfied, Dell Networking OS re-installs the route.
Configure Static Routes for the Management
Interface
When an IP address that a protocol uses and a static management route exists for the same prefix, the protocol route takes precedence
over the static management route.
To configure a static route for the management port, use the following command.
• Assign a static route to point to the management interface or forwarding router.
CONFIGURATION mode
management route ip-address mask {forwarding-router-address | ManagementEthernet slot/port}
Example of the show ip management-route Command
To view the configured static routes for the management port, use the show ip management-route command in EXEC privilege
mode.
Dell#show ip management-route
Destination
-----------
10.16.0.0/16
172.16.1.0/24
Gateway
-------
ManagementEthernet 1/1
10.16.151.4
Dist/Metric Last Change
----------- -----------
0/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
0/0 00:02:30
State Route Source
----- ------------
Connected Connected
Active Static
IPv4 Routing 363