Video Config - Panasonic BT-LH2600W Operating Instructions Manual

Main Menu
(continued)

VIDEO CONFIG

Sub menu Settings
GAMMA
<STANDARD>
*1*2
SELECT
<FILM>
<STDIO/PST>
*2
FILM GAMMA <VARICAM>
<OTHER>
COLOR TEMP.
<USER0–63>
<D93>
<D65>
<D56>
<VAR1>
<VAR2>
<VAR3>
SHARPNESS
<HIGH>
*2
<LOW>
MODE
*2
SHARPNESS H <0–30>
*2
<0–30>
SHARPNESS V
*2*6
I-P MODE <MODE2>
<MODE1>
*2
<OFF>
MONO
<ON>
*2*7
<OFF>
ANAMO
<ON>
*2
<4:3>
SD ASPECT
<16:9>
*2
SCAN <NORMAL>
<UNDER>
*2
<OFF>
NOISE WIPE
<ON>
*1 During 2 screen display, the changes are not reflected in the still image of the main window.
*2 When "RGB-COMP." is selected in "YP
*3 The following sharpness values can each be set,
1) VIDEO system input line (VIDEO,Y/C)(Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)
2) any other input line's HD (Factory settings are SHARPNESS MODE : HIGH, SHARPNESS H/V : 0)
3) any other input line's SD (Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)
and the setting values for the selected input signal from within this group is displayed. The adjustment status is
displayed in the bottom right when selected.
*4 When "VAR1", "VAR2" or "VAR3" is selected, the monitor switches to WB adjustment mode (
*5 When selecting USER0–63
1) Push [ENTER] (USER changes to blue).
*6 When using "SUB WINDOW" function (
1) change the setting after releasing "SUB WINDOW" function.
2) we recommand "MODE2" for the image with a fast movement.
*7 During Anamo size display, "SCAN" change is not reflected.
Explanation
Used to select the gamma curve.
<STANDARD>Standard mode <FILM>FILM mode
<STDIO/PST>Color emphasis mode (in the gamma characteristic in
which shades are valued more than the contrasts, it is suitable for
use by the studio and the post production, etc. )
When FILM is selected,
Used to select the type of FILM gamma mode.
<VARICAM> VARICAM use
<OTHER>
*5
Used to select the color temperature.
<USER0–63> Adjustable settings 0–63 (color temperature around 3000K–9300K)
<D93> Color temperature around 9300K
<D65> Color temperature around 6500K
<D56> Color temperature around 5600K
<VAR1> WB adjustment mode
<VAR3> WB adjustment mode
*3
Used to select the width of the sharpness edge.
<HIGH>
*3
Used to set the sharpness in the horizontal direction.
When adjusting, the item display moves to the lower part of the screen.
*3
Used to set the sharpness in the vertical direction.
When adjusting, the item display moves to the lower part of the screen.
Used to set the mode for IP change.
<MODE2>
Used to switch between color and monochrome (MONO).
<OFF> Color
* When this is ON, the picture adjusting knob [CHROMA] setting is fixed at 0.
If an Anamo lens has been used on the camera, and input through
SDI 720/60P, 59.94P, the picture is resized to Anamo size
magnification. (a vertically compressed signal can be amplified
vertically and corrected when it is displayed.)
Used for setting the aspect ratio settings when using SD signal input.
<4:3> 4:3 display
Used to set under-scan and normal display.
<NORMAL>Normal display
<OFF> This makes a fluid and smooth contrast obtainable.
This is especially effective for continuously changing the contrast of
the source signal or CG signal when the S/N is very high.
<ON> Noise reduction mode. Depending on the camera, this mode can
be especially effective for dark scenes. We recommend leaving
this setting "ON" under normal conditions.
P /RGB" in the "INPUT SELECT" menu (
B R
page 24),
The underlined values are factory preset setting values.
mark is displayed in the top left of the screen.
When using other types than VARICAM
*4
<VAR2> WB adjustment mode
*4
Thin edge <LOW>
Within Field <MODE1>
<ON>
<16:9>
<UNDER>Under-scan
2) Select 0–63 with [ ,
Thick edge
Normal mode
Monochrome
16:9 display
page 27), this does not operate.
page 20).
], and push [ENTER].
*4
19