Makita HP332D Instruction Manual
Cordless hammer driver drill
Hide thumbs
Also See for HP332D:
- Instruction manual (81 pages) ,
- Technical information (21 pages) ,
- Instruction manual (72 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita HP332D
Summary of Contents for Makita HP332D
- Page 1 INSTRUCTION MANUAL Cordless Hammer Driver Drill HP332D Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: HP332D Drilling capacities Concrete 8 mm Steel 10 mm Wood 28 mm Fastening capacities Wood screw 5.1 mm x 63 mm Machine screw No load speed High (2) 0 - 1,500 min Low (1) 0 - 450 min... -
Page 3: General Power Tool Safety Warnings
Stay alert, watch what you are doing and use The technical file in accordance with 2006/42/EC is common sense when operating a power tool. available from: Do not use a power tool while you are tired or Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium under the influence of drugs, alcohol or med- 11.6.2015 ication. A moment of inattention while operating power tools may result in serious personal injury. -
Page 4: Tips For Maintaining Maximum Battery Life
Always be sure you have a firm footing. Be also void the Makita warranty for the Makita tool and sure no one is below when using the tool in charger. high locations. -
Page 5: Functional Description
Never recharge a fully charged battery car- Battery protection system tridge. Overcharging shortens the battery service life. The tool is equipped with a battery protection system. Charge the battery cartridge with room tem- This system automatically cuts off power to the motor to perature at 10 °C - 40 °C (50 °F - 104 °F). Let extend battery life. a hot battery cartridge cool down before The tool will automatically stop during operation if the charging it. -
Page 6: Switch Action
Switch action Reversing switch action ► 1 . Switch trigger ► 1 . Reversing switch lever CAUTION: CAUTION: Before inserting the battery car- Always check the direction of tridge into the tool, always check to see that the rotation before operation. switch trigger actuates properly and returns to CAUTION: Use the reversing switch only after... -
Page 7: Adjusting The Fastening Torque
Position of Speed Torque Applicable speed operation change lever High Heavy load- ing operation High Light loading operation To change the speed, switch off the tool first. Select the "2" side for high speed or "1" for low speed but high torque. Be sure that the speed change lever is set to the correct position before operation. If the tool speed is coming down extremely during the operation with "2", slide the lever to the "1" and restart the operation. ► 1 . Action mode changing ring 2. Adjusting ring Selecting the action mode 3. -
Page 8: Operation
Installing driver bit holder ASSEMBLY Optional accessory CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing driver bit/ drill bit Optional accessory ► 1 . -
Page 9: Drilling In Metal
Drilling in metal First, turn the action mode changing ring so that the arrow on the tool body points to the marking. To prevent the drill bit from slipping when starting a Place the point of the driver bit in the screw head and hole, make an indentation with a center-punch and apply pressure to the tool. Start the tool slowly and then hammer at the point to be drilled. Place the point of the increase the speed gradually. -
Page 10: Using Holster
Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. ► 1 . Holster holder 2. Waist belt... - Page 12 Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan 885465-221 www.makita.com 20150903...