Functional Description - Makita 4112hs Instruction Manual

gap between segments of 10 mm or less, only with
a negative rake angle.
Additional Safety Warnings:
20. Be careful not to damage the spindle, the flange
(especially the installing surface) or the lock nut.
Damage to these parts could result in wheel
breakage.
21. Make sure the wheel is not contacting the
workpiece before the switch is turned on.
22. Before using the tool on an actual workpiece, let it
run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced wheel.
23. Watch out for flying sparks. Hold the tool so that
sparks fly away from you and other persons or
flammable materials.
24. Do not leave the tool running. Operate the tool
only when hand-held.
25. Do not touch the workpiece immediately after
operation; it may be extremely hot and could burn
your skin.
26. Always be sure that the tool is switched off and
unplugged or that the battery cartridge is removed
before carrying out any work on the tool.
27. Observe the instructions of the manufacturer for
correct mounting and use of wheels. Handle and
store wheels with care.
28. Do not use separate reducing bushings or
adaptors to adapt large hole abrasive wheels.
29. Use only flanges specified for this tool.
30. Check that the workpiece is properly supported.
31. Pay attention that the wheel continues to rotate
after the tool is switched off.
32. If working place is extremely hot and humid, or
badly polluted by conductive dust, use a short-
circuit breaker (30 mA) to assure operator safety.
33. Do not use the tool on any materials containing
asbestos.
34. Do not use water or grinding lubricant.
35. Ensure that ventilation openings are kept clear
when working in dusty conditions. If it should
become necessary to clear dust, first disconnect
the tool from the mains supply (use non metallic
objects) and avoid damaging internal parts.
36. Cutting discs must not be subjected to any lateral
pressure.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure to
follow the safety rules stated in this instruction
manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Adjusting the depth of cut (Fig. 1)
Loosen the wing bolt on the depth guide and move the
base up or down. At the desired depth of cut, secure the
base by tightening the wing bolt.
Securing wheel guard (Fig. 2)
CAUTION:
• The wheel guard must be adjusted on the tool so that
the closed side of the guard always points toward the
operator.
The wheel guard can be adjusted about 80 degrees, after
you loosen the clamping nut. Adjust to the desired angle,
then secure the clamping nut.
Switch action (Fig. 3)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
For tool with the lock-on switch
To start the tool, simply pull the switch trigger
(A direction). Release the switch trigger to stop.
For continuous operation, pull the switch trigger
(A direction) and then push in the lock lever (B direction).
To stop the tool from the locked position, pull the switch
trigger (A direction) fully, then release it.
For tool with the lock-off switch
To prevent the switch trigger from accidentally pulled, a
lock lever is provided.
To start the tool, push in the lock lever (B direction) and
then pull the switch trigger (A direction). Release the
switch trigger to stop.
For tool with the lock on and lock-off switch
To prevent the switch trigger from accidentally pulled, a
lock lever is provided.
To start the tool, push in the lock lever (B direction) and
then pull the switch trigger (A direction). Release the
switch trigger to stop.
For continuous operation, push in the lock lever,
(B direction) pull the switch trigger (A direction) and then
push the lock lever (B direction) further in.
To stop the tool from the locked position, pull the switch
trigger (A direction) fully, then release it.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing or removing the wheel
To remove the wheel, depress the shaft lock to hold the
shaft stationary, then loosen the hex bolt clockwise with
the socket wrench.
To install a wheel, place flange with its partly elevated
side facing the tool, and then place ring before installing a
wheel onto the spindle (shaft) and another flange with
partly elevated side facing outward.
Be sure to fully tighten the hex bolt counterclockwise after
mounting the new wheel, or operation will be dangerous.
(Fig. 4 & 5)
7