Specifications - Makita BDF460 Instruction Manual

ENGLISH
1 Button
2 Battery cartridge
3 Terminal cover
4 Charging light
5 Grip base
6 Teeth
7 Side grip
8 Loosen
9 Tighten
0 Depth rod

SPECIFICATIONS

Model
Capacities
Steel ............................................................ 13 mm
Wood ........................................................... 38 mm
Wood screw ................................. 10 mm x 90 mm
Machine screw .............................................. 6 mm
-1
No load speed (min )
High ......................................................... 0 – 1,500
Low ............................................................. 0 – 460
Overall length ............................................... 259 mm
Net weight
(with battery cartridge) .................................... 2.6 kg
Rated voltage ............................................ D.C. 24 V
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY
CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating
instructions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
3. CAUTION — To reduce risk of injury, charge
only MAKITA type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or
sold by the battery charger manufacturer may
result in a risk of fire, electric shock, or injury
to persons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when dis-
connecting charger.
4
Explanation of general view
q Thumb screw
w Sleeve
e Bit
r Bit holder
t Switch trigger
y Reversing switch lever
u A side
i B side
o Clockwise
p Counterclockwise
7. Make sure cord is located so that it will not be
BDF460
8. Do not operate charger with damaged cord or
9. Do not operate charger if it has received a
10. Do not disassemble charger or battery car-
11. To reduce risk of electric shock, unplug
12. The battery charger is not intended for use by
13. Young children should be supervised to
ADDITIONAL SAFETY RULES FOR
CHARGER & BATTERY CARTRIDGE
ENC002-2
1. Do not charge battery cartridge when tempera-
2. Do not attempt to use a step-up transformer,
3. Do not allow anything to cover or clog the
4. Do not short the battery cartridge:
5. Do not store the tool and battery cartridge in
a Low speed
s High speed
d Speed change lever
f Graduations
g Adjusting ring
h Drill marking
j Pointer
k Limit mark
l Brush holder cap
; Screwdriver
stepped on, tripped over, or otherwise sub-
jected to damage or stress.
plug — replace them immediately.
sharp blow, been dropped, or otherwise dam-
aged in any way; take it to a qualified service-
man.
tridge; take it to a qualified serviceman when
service or repair is required. Incorrect reas-
sembly may result in a risk of electric shock or
fire.
charger from outlet before attempting any
maintenance or cleaning. Turning off controls
will not reduce this risk.
young children or infirm persons without
supervision.
ensure that they do not play with the battery
charger.
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
an engine generator or DC power receptacle.
charger vents.
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
locations where the temperature may reach or
exceed 50°C (122°F).