Makita DHS680 Instruction Manual
Hide thumbs
Also See for DHS680:
- Instruction manual (100 pages) ,
- Technical information (19 pages) ,
- Instruction manual (89 pages)
Related Manuals for Makita DHS680
Summary of Contents for Makita DHS680
- Page 1 INSTRUCTION MANUAL Cordless Circular Saw DHS680 015156 IMPORTANT: Read Before Using.
-
Page 2: Specifications
With the times when the tool is switched off and when it appropriate Makita genuine saw blades, other materials is running idle in addition to the trigger time). can also be sawed. - Page 3 The technical file in accordance with 2006/42/EC is moving parts. Damaged or entangled cords available from: increase the risk of electric shock. Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use 18.3.2014 of a cord suitable for outdoor use reduces the risk of electric shock.
- Page 4 18. Do not use the power tool if the switch does 29. Follow instruction lubricating not turn it on and off. Any power tool that changing accessories. cannot be controlled with the switch is dangerous 30. Keep handles dry, clean and free from oil and and must be repaired.
- Page 5 Kickback causes and related warnings − kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator; − when the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator;...
- Page 6 19. Check the operation of the lower guard spring. If the guard and the spring are not operating Fig. 1 properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a build-up of debris.
- Page 7 32. Only use the saw blade with the diameter that Do not store the tool and battery cartridge in is marked on the tool or specified in the locations where the temperature may reach or exceed 50 ﾟ C (122 ﾟ F). manual.
-
Page 8: Functional Description
Hold the tool and the battery cartridge firmly when lock-off lever. Return tool to a MAKITA service • installing or removing battery cartridge. Failure to center for proper repairs BEFORE further usage. - Page 9 Overheat protection for tool When tool overheated, tool stops Battery indicator status automatically and the battery indicator shows following Remaining battery capacity Blinking state. In this situation, let the tool cool before turning the tool on again. 50% - 100% Battery indicator Blinking 20% - 50%...
-
Page 10: Bevel Cutting
Do not look in the lamp or see the source of lamp directly. • Removing or installing saw blade 1. Lamp CAUTION: Be sure the blade is installed with teeth pointing • up at the front of the tool. Use only the Makita wrench to install or remove • the blade. 015154... - Page 11 Next, mount the inner flange onto the mounting shaft so that 1. Hex wrench the correct side of protrusion on the inner flange faces 2. Shaft lock outward and then place saw blade and outer flange. 3. Tighten SURE TIGHTEN BOLT 4.
- Page 12 (Guide rule) 015112 When you wish to perform clean cutting operation, connect a Makita vacuum cleaner to your tool. 015118 Install the dust nozzle on the tool using the screw. Then The handy rip fence allows you to do extra-accurate connect a hose of the vacuum cleaner to the dust straight cuts.
-
Page 13: Optional Accessories
Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. 015113 Saw blades • 1. Triangular rule Rip fence (Guide rule) •... - Page 16 Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan www.makita.com 885374A224...