Cisco TelePresence System Codec C40 Administrator's Manual page 107

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60
Contents
Video SelfviewDefault Mode
Determine if the main video source (self view) shall be displayed on screen after a call.
The position and size of the self view window is determined by the Video SelfviewDefault
PIPPosition and the Video Selfview FullscreenMode settings respectively.
This setting obsoletes the Video Selfview setting as from TC6.0.
Requires user role: ADMIN
Value space: <Off/Current/On>
Off: Self view is switched off when leaving a call.
Current: Self view is left as is, i.e. if it was on during the call, it remains on after the call; if it
was off during the call, it remains off after the call.
On: Self view is switched on when leaving a call.
Video SelfviewDefault Mode: Current
Example:
Video SelfviewDefault FullscreenMode
Determine if the main video source (self view) shall be shown in full screen or as a small
picture-in-picture (PiP) after a call. The setting only takes effect when self view is switched on
(see the Video SelfviewDefault Mode setting).
Requires user role: ADMIN
Value space: <Off/Current/On>
Off: Self view will be shown as a PiP.
Current: The size of the self view picture will be kept unchanged when leaving a call, i.e. if it
was a PiP during the call, it remains a PiP after the call; if it was fullscreen during the call, it
remains fullscreen after the call.
On: The self view picture will be shown in fullscreen.
Video SelfviewDefault FullscreenMode: Current
Example:
D14636.10 Profile C60-C40 and Codec C60-C40
Introduction Web interface
Administrator Guide TC6.1, APRIL 2013.
System settings System settings
Video SelfviewDefault PIPPosition
Determine the position on screen of the small self view picture-in-picture (PiP) after a call. The
setting only takes effect when self view is switched on (see the Video SelfviewDefault Mode
setting) and fullscreen view is switched off (see the Video SelfviewDefault FullscreenMode
setting).
This setting obsoletes the Video SelfviewPosition setting as from TC6.0.
Requires user role: ADMIN
Value space: <Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/
LowerRight >
Current: The position of the self view PiP will be kept unchanged when leaving a call.
UpperLeft: The self view PiP will appear in the upper left corner of the screen.
UpperCenter: The self view PiP will appear in the upper center position.
UpperRight: The self view PiP will appear in the upper right corner of the screen.
CenterLeft: The self view PiP will appear in the center left position.
CentreRight: The self view PiP will appear in the center right position.
LowerLeft: The self view PiP will appear in the lower left corner of the screen.
LowerRight: The self view PiP will appear in the lower right corner of the screen.
Video SelfviewDefault PIPPosition: Current
Example:
Video SelfviewDefault OnMonitorRole
Determine which monitor/output to display the main video source (self view) on after a call.
The value reflects the monitor roles set for the different outputs in the Video Output HDMI/DVI/
Composite MonitorRole settings.
The setting applies both when self view is displayed in full screen, and when it is displayed as
picture-in-picture (PiP), but only if the Video Monitors setting is set to Dual.
Requires user role: ADMIN
Value space: <First/Second/Current>
First: The self view picture will be shown on outputs with the Video Output HDMI/DVI/
Composite MonitorRole set to First.
Second: The self view picture will be shown on outputs with the Video Output HDMI/DVI/
Composite MonitorRole set to Second.
Current: When leaving the call, the selfv iew picture will be kept on the same output as
during the call.
Video SelfviewDefault OnMonitorRole: Current
Example:
www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reserved.
107
Administrator Guide
Setting passwords Appendices