Sony HXCU-FB80 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Control Unit
  5. HXCU-FB80
  6. Service manual

Sony HXCU-FB80 Service Manual

4k/hd camera control unit
Hide thumbs Also See for HXCU-FB80:
Table of Contents

Advertisement

Quick Links

4K/HD CAMERA CONTROL UNIT
HXCU-FB80
SERVICE MANUAL
1st Edition

Advertisement

Table of Contents
loading

Related Manuals for Sony HXCU-FB80

Summary of Contents for Sony HXCU-FB80

  • Page 1 4K/HD CAMERA CONTROL UNIT HXCU-FB80 SERVICE MANUAL 1st Edition...
  • Page 2 Pour toute réparation faire appel à une personne compétente uniquement. 安全のために，周辺機器を接続する際は，過大電圧を持 つ可能性があるコネクターを以下のポートに接続しない でください。 : LAN コネクター 上記のポートについては本書の指示に従ってくだい。 For safety, do not connect the connector for peripheral device wiring that might have excessive voltage to the following port. : LAN connector Follow the instructions for the port. HXCU-FB80...
  • Page 3 Batterien nur durch den vom Hersteller empfohlenen Kasser batteriet i henhold til gjeldende avfallsregler. oder einen gleichwertigen Typ ersetzen. Wenn Sie die Batterie entsorgen, müssen Sie die Gesetze der jeweiligen Region und des jeweiligen Landes befolgen. HXCU-FB80...
  • Page 4 CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. The HXCU-FB80 is classified as a CLASS 1 LASER PRODUCT. HXCU-FB80...

  • Page 5: Table Of Contents

    CN-3985 Board......................3-22 HXCU-FB80...
  • Page 6 SW-1736 Board......................7-3 HXCU-FB80...
  • Page 7 Frame Wiring......................... . . 9-3 Revision History HXCU-FB80...

  • Page 9: Manual Structure

    Related manuals The following manuals are available for this model. If any of these manuals is required, please contact your local Sony Sales Office/Service Center. • Operating Instructions CD-ROM (supplied with the unit) This manual contains information required to operate and use the unit.

  • Page 11: Service Overview

    Section 1 Service Overview 1-1. Location of Printed Wiring Boards PS-934 CN-3972 CN-3958 LED-545 CN-3968 CN-3985 AT-196 SW-1736 LED-544 DPR-386 HXCU-FB80...

  • Page 12: Functions Of Onboard Parts

    Lit red: Access to the memory stick in progress. Do not remove the memory stick. Lit green: The inserted memory stick can be re- moved. D700 CONF DONE Lights when there is a problem with the configu- ration of any FPGA (IC400) on the AT-196 board. HXCU-FB80...
  • Page 13 Color Description Normal state D114 Green Lights when all power voltages on the DPR-386 board are normal. D701 CONF DONE Lights when there is a problem with the configu- ration of any FPGA (IC600, IC2300) on the DPR-386 board. HXCU-FB80...

  • Page 14: Functions Of Onboard Switches

    Do not change the settings of unused switches. Ref.No. Name Description Factory setting S200 VerUp Used to enable software upgrade using a memory stick. PLD VerUp Used to enable PLD upgrade using a memory stick. NORMAL/DEBUG Not used NORMAL/DEBUG Not used HXCU-FB80...
  • Page 15 PS-934 board S002 PS-934 board (Side A) Ref.No. Name Description Factory setting S002 DC-DC control ON/OFF for camera power output When this switch is set to ON, 48 V power is always output. HXCU-FB80...

  • Page 16: Note On Replacement Of Lithium Battery

    BATTERY, LITHIUM (CR2032 For real time clock (RTC) backup 1-528-174-74 TYPE) CAUTION In replacing, ensure that the battery is installed with “+” and “-” poles connected to the correct terminals. Improper connection may cause an explosion or leakage of fluid. HXCU-FB80...

  • Page 17: Notes On Replacement Of Circuit Board

    The table below lists data retained in the EEPROM on respective boards. Note The part number listed in “Spare Parts” is for EEPROM which is not programmed. Therefore, program a new EEPROM after replacement. For details, contact your local Sony Sales Office/Service Center. Board name Ref. No.

  • Page 18: Circuit Protection Parts

    500 mA/20 ℃ THP110 1-803-615-21 1.1 A/20 ℃ THP111 1-804-616-21 2.5 A/20 ℃ THP114 1-804-987-21 1.1 A/20 ℃ THP115 1-804-616-21 1.1 A/20 ℃ THP118 1-804-616-21 1.1 A/20 ℃ THP121 1-804-616-21 1.1 A/20 ℃ THP122 1-804-616-21 1.1 A/20 ℃ PS-934 TH201 1-811-308-21 HXCU-FB80...

  • Page 19: Flexible Flat Cable And Coaxial Cable

    Insert the flexible card wire fully into the connector. Push the connector open/close section to lock the flexible card wire. Connecting/Disconnecting Flexible Card Wire (Type B Connector) Disconnecting Connecting Open/close section Open/close section Isolation surface Isolation surface (blue) (blue) Connector Connector HXCU-FB80...

  • Page 20: Disconnecting/Connecting Fine-Wire Coaxial Cable

    Do not attempt to disconnect by pulling the cable. Raise the pull-bar in the direction of arrow A to unlock it. Hold both sides of the fine-wire coaxial cable connector, and pull the connector straight to disconnect it. 1-10 HXCU-FB80...
  • Page 21 Insert the connector carefully so that the connector guides are not caught by the edge of the mating connector. Hold both sides of the fine-wire coaxial cable connector with the contact surface facing up. Insert the connector straight to meet the angle specified. Turn the pull-bar in the direction of arrow B and lock it. 1-11 HXCU-FB80...

  • Page 22: Lead-Free Solder

    • The ordinary soldering iron can be used but the iron tip has to be applied to the solder joint for a slightly longer time. The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful. 1-12 HXCU-FB80...

  • Page 23: Periodic Maintenance And Inspection

    • FOCD-DC125 (DRY Cleaner, 1.25mm) manufactured by NEUTRIK, 9393 (IBC™ Brand Cleaner LC, 1.25mm) manufactured by US CONEC, or equivalent. Cleaning of male connector While pushing the shell, clean the tip of the white optical contacts using the optical connector cleaner. The sealing shutter is released while the shell is being pushed. HXCU-FB80...
  • Page 24 • Cotton swabs (commercially available) Cleaning of male connector While pushing the shell, clean the tip of the white optical contacts with a cotton swab moistened with alcohol. The sealing shutter is released while the shell is being pushed. HXCU-FB80...

  • Page 25: Cleaning Connectors/Cables Of Lemo

    • Alcohol is not necessary during cleaning. • Number of possible wipes is one cleaning per a piece. Do not reuse it. Cleaning of Male Connector Clean the tip of the white optical contacts using the optical connector cleaner. HXCU-FB80...
  • Page 26 Tool and Fixtures • Alignment sleeve remover HC-001 (for female connector) Sony Part No. : J-6480-010-A or DCC.91.312.5LA manufactured by LEMO, or equivalent Note Insert the shorter nose end when removing/installing the alignment sleeve. Grasp not the shock absorber portion of the remover but the handle in use.
  • Page 27 The alignment sleeve can be removed/reinstalled with the sleeve itself attached to the tip of the remover. Great care should be taken so as not to lose or damage the alignment sleeve. Alignment sleeve: Sony Part No. : 9-980-074-01 Alignment sleeve Clean the tip of the white optical contacts with a cotton swab moistened with alcohol.
  • Page 28 Optical contact (white) HXCU-FB80...

  • Page 29: Replacement Of Main Parts

    M2.6 x 5: 0.53 ±0.07 N·m PSW3 x 6: 0.80 ±0.12 N·m PSW3 x 10: 0.80 ±0.12 N·m PSW4 x 8: 1.4 ±0.1 N·m When using the torque driver with the notation of cN·m, interpret it as follows. Example: 0.8 N·m = 80 cN·m HXCU-FB80...

  • Page 30: Cover

    3-2. Cover Procedure Remove the seven screws, then remove the cover. PSW3 x 6 Cover The illustration shows LEMO model. Install the removed parts by reversing the steps of removal. HXCU-FB80...

  • Page 31: Front Panel Assembly

    Disconnect the flexible flat cable (45 core) from the connector (CN3) on the SW-1736 board. Remove the four screws, then remove the front panel assembly. Front panel assembly 3 x 6 3 x 6 Flexible flat cable (45 core) SW-1736 board Install the removed parts by reversing the steps of removal. HXCU-FB80...

  • Page 32: Board

    PS-934 Board Preparation Remove the cover. (Refer to “3-2. Cover”.) Procedure Disconnect the seven harnesses from the seven connectors (CN001 to CN007) on the PS-934 board. PS-934 board Harness CN003 CN006 CN005 CN002 Harnesses CN001 CN004 CN007 Harnesses PS-934 board HXCU-FB80...
  • Page 33 Holes CN006 Note Carefully stick the electric heat sheet (PS-R2) to the new PS-934 board along lines (a) so as not to block the two holes in the board. Install the removed parts by reversing the steps of removal. HXCU-FB80...

  • Page 34: Dc Fan

    (1) Open the edge saddle. (2) Disconnect the harness from the connector (CN003) on the PS-934 board. (3) Remove the screw, then remove the fan assembly. 3 x 6 Fan assembly Harness PS-934 board CN003 Edge saddle The illustration shows LEMO model. HXCU-FB80...
  • Page 35 (2) Remove the fan cushion from the DC fan. DC Fan Fan duct Label Fan cushion Harness Note Install the DC fan carefully paying attention to the label side and the harness position. Install the removed parts by reversing the steps of removal. HXCU-FB80...

  • Page 36: Switching Regulator (Large)

    Remove the heat transfer sheet PS-R1 from the switching regulator (large). 3 x 6 Heat transfer sheet PS-R1 Switching regulator (large) Harness CN53 CN51 Harnesses The illustration shows LEMO model. Install the removed parts by reversing the steps of removal. HXCU-FB80...

  • Page 37: Switching Regulator (Small)

    Remove the four screws, then remove the switching regulator (small). 3 x 6 PS bracket Insulating sheet PS-B 3 x 6 Harness CN51 Harness Switching regulator (small) The illustration shows LEMO model. Install the removed parts by reversing the steps of removal. HXCU-FB80...

  • Page 38: Board And Lithium Battery

    Note • When connecting the optical fiber cables, clean the end of cables. • When connecting the optical fiber cables, route them as shown in the illustration. 13. Install the removed parts by reversing the steps of removal. 3-10 HXCU-FB80...

  • Page 39: Optical Connector Assembly

    For the connection of the optical fiber cables, refer to the indication on the AT-196 board. Clamper (1) Optical connector CN004 Clamper (3) Clamper (4) 1 2 Neutrlk 2 1 LEMO Neutrik connector AT-196 board AT-196 board Optical fiber cables 3-11 HXCU-FB80...

  • Page 40: Lemo Model

    • When connecting the Neutrik connector, make sure that the directions of the bracket and Neutrik connector are correct. Install the removed parts by reversing the steps of removal. 3-9-2. LEMO Model Preparation Remove the cover. (Refer to “3-2. Cover”.) 3-12 HXCU-FB80...
  • Page 41 For the connection of the optical fiber cables, refer to the indication on the AT-196 board. Clamper (2) Optical connector CN004 Clamper (3) Clamper (4) 1 2 Neutrlk 2 1 LEMO AT-196 board LEMO connector AT-196 board Optical fiber cables 3-13 HXCU-FB80...
  • Page 42 • When attaching the bracket, align the four bosses with the four holes. • When attaching the LEMO connector, make sure that the directions of the bracket and LEMO connector are correct. Install the removed parts by reversing the steps of removal. 3-14 HXCU-FB80...

  • Page 43: Cn-3958 Board

    Remove the six screws (BTP3 x 10) and four screws (BTP2.6 x 10), then remove the CN-3958 board in the direction of the arrow. Harness Clamper CN-3958 board Clampers Flexible flat cable (45 core) 2.6 x 10 2.6 x 10 3 x 10 The illustration shows LEMO model. Install the removed parts by reversing the steps of removal. 3-15 HXCU-FB80...

  • Page 44: Cn-3968 Board

    Remove the two screws, then remove the CN-3968 board. Disconnect the two harnesses from the connectors (CN1 and CN003) on the CN-3968 board. Harness CN-3968 board CN003 Harness 2.6 x 5 Rear panel Install the removed parts by reversing the steps of removal. 3-16 HXCU-FB80...

  • Page 45: Board

    3 x 6 3 x 6 Flexible flat cable (45 core) DPR-386 board 3 x 6 DPR block PS-934 board CN002 CN006 CN005 Harness Harness Cord clamper Clamper CN007 3 x 6 The illustration shows LEMO model. Harnesses 3-17 HXCU-FB80...
  • Page 46 Flexible flat cable (45 core) Harness Harness CN102 CN402 DPR-386 board Fine-wire coaxial cable Flexible flat cable CN101 (10 core) Supplied hex screws 2.6 x 5 DPR bracket 3 x 10 Install the removed parts by reversing the steps of removal. 3-18 HXCU-FB80...

  • Page 47: Cn-3972 Board

    Disconnect the flexible flat cable (10 core) from the connector (CN003) on the CN-3972 board. Remove the two supplied hex screws, then remove the CN-3972 board. DPR block Flexible flat cable (10 core) Supplied hex screws CN003 CN-3972 board Install the removed parts by reversing the steps of removal. 3-19 HXCU-FB80...

  • Page 48: Sw-1736 Board

    Remove the front panel assembly. (Refer to “3-3. Front Panel Assembly”.) Procedure Remove the five knob assemblies (S), the volume knob assembly (small) and volume knob assembly (large). Front panel assembly Five knob assembles (S) Volume knob assembly (small) Volume knob assembly (large) 3-20 HXCU-FB80...
  • Page 49 • When installing the SW-1736 board, push the SW-1736 board in the direction of the arrow and attach the screw (a) first. SW-1736 board • When installing the SW-1736 board, process the harness under the CN-3985 board as shown in the illustration. CN-3985 board Harness Install the removed parts by reversing the steps of removal. 3-21 HXCU-FB80...

  • Page 50: Cn-3985 Board

    3 x 6 CN-3985 board Hole Boss Remove the two screws, then remove the INCOM plate from the CN-3985 board. INCOM plate CN-3985 board 3 x 10 3 x 10 Install the removed parts by reversing the steps of removal. 3-22 HXCU-FB80...

  • Page 51: Led-544 Board

    Remove the screw, then remove the LED-544 board. 3 x 6 LED-544 board Holes Bosses Note When installing the LED-544 board, align the two bosses with the two holes. Install the removed parts by reversing the steps of removal. 3-23 HXCU-FB80...
  • Page 52 Disconnect the flexible flat cable (10 core) from the connector (CN1) on the LED-545 board. Remove the screw, then remove the LED-545 board. 3 x 6 Flexible flat cable (10 core) LED-545 board Install the removed parts by reversing the steps of removal. 3-24 HXCU-FB80...

  • Page 53: Electrical Alignment

    4-1-3. Connection of Equipment Transmittable Optoelectrical composite cable: CCFN-25/50/100 Audio oscillator HD color camera HXC-FB80 Signal generator 4K/HD camera control unit Optoelectrical HXCU-FB80 REFERENCE composite cable /DPR-386 Waveform monitor CCA-5 cable (max. 50 m) PIX/CN-3598 75 Ω 75 Ω Remote control panel...

  • Page 54: Initial Settings

    • CCU CONFIGURATION menu C07: INCOM MIC → CARBON • Front panel INTERCOM switch → PROD Except for these settings, do not change the switch settings made when the unit was shipped. (Refer to “1-2-2. Functions of Onboard Switches”.) HXCU-FB80...

  • Page 55: Reference Signal System Adjustment

    Adjust the [VCO SDCK] value so that the frequency falls within the range of 27 MHz ±50 Hz. Set [VCO SDCK] to OFF. Select [STORE] and store the value. Finish the maintenance mode. Setting after Adjustment After this adjustment is completed, reconnect the disconnected cable. HXCU-FB80...

  • Page 56: Video Signal System Adjustment

    Settings C01: COLOR BAR SD BAR SMPTE (NTSC) EBU (PAL) C10:VIDEO ADJUST PIX LEVEL PIX CHROMA Adjustment Equipment: SD waveform monitor Test Point: PIX OUT connector / rear panel Adjusting Point: MAINTENANCE menu → M05: PIX LEVEL Specification : HXCU-FB80...
  • Page 57 • A = 140 ± 1 IRE (75 Ω termination) • B = 1000 ± 7 mV (75 Ω termination) NTSC HXCU-FB80...

  • Page 58: Cable Driver Adjustment

    (1) While monitoring the waveform monitor, adjust the [SDI2-2 3G] value so that the amplitude meets the specified value (800 ±80 mV). Set to cursor at [STORE] and press the CONTROL knob. When “Write OK?” appears, press the CONTROL knob. The adjustment values are stored. HXCU-FB80...

  • Page 59: Adjusting Hd-Sdi Amplitude

    (2) While monitoring the waveform monitor, adjust the [SDI2-2 1.5G] value so that the amplitude meets the specified value (800 ±80 mV). Set to cursor at [STORE] and press the CONTROL knob. When “Write OK?” appears, press the CONTROL knob. The adjustment values are stored. HXCU-FB80...

  • Page 61: Software Update

    Copy the upgrading program to the Memory Stick in the following steps. Note To get the upgrading program (program files “HXCUFB80.rom” and “HXCUFB80_BOOT.rom”), contact your local Sony Sales Office/Service Center. Make the following directory on the Memory Stick. ¥MSSONY ¥PRO ¥CAMERA¥HXCUFB80 Copy the program files “HXCUFB80.rom”...

  • Page 62: Updating The Boot Program

    Check that the main program has been upgraded with “ROM Version” of status display. (Refer to the Operating Instructions.) 5-1-2. Updating the BOOT Program Equipment required • Memory Stick Check Check the current boot program version with Firmware Update of the MAINTENANCE menu. (Refer to Section 6-3.) HXCU-FB80...
  • Page 63 Copy the upgrading program to the Memory Stick in the following steps. Note To get the upgrading program (program files “HXCUFB80.rom” and “HXCUFB80_BOOT.rom”), contact your local Sony Sales Office/Service Center. (1) Make the following directory on the Memory Stick. ¥MSSONY¥PRO¥CAMERA¥HXCUFB80 (2) Copy the program files “HXCUFB80.rom”...

  • Page 64: Writing And Rewriting The Pld Internal Data

    This unit is provided with programmable logic devices (PLDs). They can be programmed and reprogrammed by the MAIN program. If the parts listed below needs to be replaced or if PLD needs to be upgraded, contact your local Sony Sales Office/ Service Center.

  • Page 65: Maintenance Mode

    Turn the CANCEL/ENTER lever quickly to the CANCEL side twice. Changing Setting Values To enter: Press the CONTROL knob. To cancel: Turn the CANCEL/ENTER lever to the CANCEL side before pressing the CONTROL knob. The setting of the selected item is restored. HXCU-FB80...

  • Page 66: Memory Stick

    Turn the DISP/MENU lever to the MENU side. The menu disappears. To restart the setting operation, turn the DISP/ MENU lever again to the MENU side. 6-1-2. Memory Stick The following types of Memory Stick are available for this unit. • Memory Stick Duo • Memory Stick PRO Duo (Up to 2 GB) HXCU-FB80...

  • Page 67: Ve Operation Menu

    Menu screen Item Description STORE FILE Registers the current adjustment values as an < O H B F I L E > V 0 3 T O P → OHB file. S T O R E F I L E HXCU-FB80...
  • Page 68 ±99 F L A R E V M O D O N D . S H A D : O F F FLARE ON/OFF T E S T : O F F V MOD ON/OFF D.SHAD ON/OFF TEST OFF/1/2 HXCU-FB80...
  • Page 69 KNEE SAT ±99 A U T O K N E E : O F F ON/OFF P O I N T L I M I T : S L O P E AUTO KNEE OFF/AUTO POINT LIMIT ±99 SLOPE ±99 HXCU-FB80...
  • Page 70 L I M I T E R [ M ] : [WHT] ±99 　 [ W H T ] : [ B L K ] : C R I S P 　 [BLK] ±99 L V L D E P CRISP 　 ±99 LEVEL DEP 　 ±99 ON/OFF HXCU-FB80...
  • Page 71 H / V R A T I O : - - - CRISP ±99 F R E Q : - - - LVL DEP ±99 ON/OFF H/V RATIO ±99 FREQ ±99 V16: SKIN DETAIL This unit controls only channel [1]. HXCU-FB80...
  • Page 72 Setting SUPPRESSION ±99 < C R O S S C O L O R > V 1 9 T O P ON/OFF → S U P P R E S S I O N : : O F F HXCU-FB80...
  • Page 73 V 2 3 T O P → CCR LEVEL ±99 C C R : O F F C C R L E V E L : CCR CORING ±99 C C R C O R I N G : HXCU-FB80...
  • Page 74 　 　 SHADING 　 Place the cursor at “AUTO BLACK SHADING”, and turn the CANCEL/ENTER lever to the ENTER side. To cancel: Turn the CANCEL/ENTER lev- er to the ENTER side during ex- ecution. GAIN BOUNCE ON/OFF 　 6-10 HXCU-FB80...
  • Page 75 O H B M A T R I X : O F F ±99 Adjust the OHB multi-matrix correction value of hue for each PHASE (16 angles). ±99 Adjusts the OHB multi-matrix correction value of saturation for each PHASE (16 angles). OHB MATRIX ON/OFF 　 6-11 HXCU-FB80...
  • Page 76 M O N O C O L O R : O F F to 90 when the rotary encoder is rota- P H A S E S A T U R A T I O N : ted clockwise. SATURATION ±99 　 6-12 HXCU-FB80...

  • Page 77: Maintenance Menu

    EEPROM (IC309) on the DPR-386 board. NAME HXCU-FB80 S E R I A L N O : 0 0 0 0 0 0 0 0 N A M E : H X C U - F B 8 0 DEST...
  • Page 78 : V 1 . 0 0 Upgrades all ROM files stored in the Memory Stick. AUTO Upgrades only files later than the current version A L L A U T O of relevant ROMs in the Memory Stick. 6-14 HXCU-FB80...
  • Page 79 Adjust the SLOT2-2 3 G out- put level. 1.5 G 00h to FFh Adjust the SLOT2-2 1.5 G ON/OFF output level. STORE Writes the above cropping setting values to the EE- PROM. CLEAR Clears the above adjustment values. 6-15 HXCU-FB80...

  • Page 81: Circuit Description

    Command signals with the panel are processed by the AT-196 board. 7-1-4. CN-3972 Board The CN-3972 board contains a D-sub 9-pin connector for TRUNK LINE interface and an RS-422A/RS-232C driver circuit (IC004) and is connected to the DPR-386 board through a flexible flat cable. HXCU-FB80...

  • Page 82: Cn-3985 Board

    The PS-934 board relays camera power and CCU power signals. This board contains circuits for camera power ON/OFF control, overcurrent detection, output control, and remote output DC-DC power. If the ambient temperature of the PS-934 board becomes abnormal, “TEMP NG” appears disabling camera output. HXCU-FB80...

  • Page 83: Sw-1736 Board

    • CCU menu operation switch and rotary encoder • Switch and microphone amplifier for the front intercom Front intercom microphone amplifier gain, bias power ON/OFF, balance/unbalance switching, and lock switch target item selection are set by the CCU menu. HXCU-FB80...

  • Page 85: Spare Parts

    Therefore, specified parts should be used in the case 指定の部品を使ってください。 of replacement. 2.  部品の共通化 2. Standardization of Parts Some repair parts supplied by Sony differ from those ソニーから供給する補修用部品は，セットに使われ used for the unit. These are because of parts common- ているものと異なることがあります。 ality and improvement.

  • Page 86: Exploded Views

    1-831-108-11 s CABLE, FLEXIBLE FLAT (45 CORE) 7-682-949-01 s SCREW +PSW 3X10 1-967-976-11 s HARNESS, SUB (POWER CONT) 1-971-941-11 s HARNESS, SUB (CCU DC OUT) SP 4-299-617-01 s COVER 4-299-632-01 s RACK BRACKET(U) 4-382-854-51 s SCREW (M3X6), P, SW (+) 4-446-014-01 s TAPE AS (2040) HXCU-FB80...

  • Page 87: Ps Block

    1-474-700-11 s REGULATOR, SWITCHING 1-474-701-11 s REGULATOR, SWITCHING 1-967-974-11 s HARNESS, SUB (DC OUT) 1-971-941-11 s HARNESS, SUB (CCU DC OUT) SP 3-853-802-01 s CLAMP,REUSE 4-382-854-51 s SCREW (M3X6), P, SW (+) 4-641-552-01 o SADDLE, LOCK EDGE 4-731-146-01 s SHEET (PS-R1), ELECTRIC HXCU-FB80...
  • Page 88 SP Description A-1906-334-A s OPTICAL CONNECTOR(CCU)ASSY 1-831-081-11 s CABLE, FLEXIBLE FLAT (45 CORE) A-2195-918-A s AT-196 COMPL 1-510-039-11 s OPTICAL MODULE (1.8725/3.7G) 1-846-443-11 s CABLE, LC-LC 3-079-115-01 s TAPE AS 1-528-174-74 s BATTERY, LITHIUM (CR2032 TYPE) 3-637-901-02 s SCREW M2.6X5 HXCU-FB80...
  • Page 89 SP Description 3-853-802-01 s CLAMP,REUSE 4-382-854-11 s SCREW (M3X10), P, SW (+) 4-382-854-51 s SCREW (M3X6), P, SW (+) 4-436-986-01 s SHEET,RADIATION 30X30X1.5 4-444-729-02 s CAP, NEUTRIK FIBER 4-444-793-01 s PLATE,CONNECTER(LEMO) 4-669-854-01 s CAGE, TOP 7-682-248-04 s SCREW +K 3X8 HXCU-FB80...

  • Page 90: Dpr Block

    A-2195-919-A s DPR-386 COMPL 1-831-081-11 s CABLE, FLEXIBLE FLAT (45 CORE) 1-836-689-11 s CABLE, FLEXIBLE FLAT (10 CORE) 3-637-901-02 s SCREW M2.6X5 3-853-802-01 s CLAMP,REUSE 7-685-535-19 s SCREW +BTP 2.6X10 TYPE2 N-S 7-685-547-14 s SCREW +BTP 3X10 TYPE2 N-S HXCU-FB80...
  • Page 91 1-855-252-11 s FAN, DC (60 SQUARE) 1-967-973-11 s HARNESS (AC IN) 2-990-241-02 s HOLDER (A), PLUG 3-257-200-01 s CLAMP, CORD 4-139-239-01 s FAN CUSHION 4-382-854-51 s SCREW (M3X6), P, SW (+) 7-682-949-01 s SCREW +PSW 3X10 7-682-961-01 s SCREW +PSW 4X8 HXCU-FB80...

  • Page 92: Front Panel

    2-139-192-01 s FRAME, INDICATOR WINDOW 2-139-193-02 s WINDOW, INDICATOR 2-249-353-01 s COVER, LAMP 3-725-295-21 s SCREW, (+) (B3) 3-872-590-01 s PORONSHEET(POWER) 4-139-232-01 s KNOB, ROTARY ENCODER 4-299-616-03 s PLATE,FRONT 4-299-629-03 s PANEL,FRONT(U) 4-382-854-51 s SCREW (M3X6), P, SW (+) HXCU-FB80...

  • Page 93: Supplied Accessories

    8-3. Supplied Accessories Q'ty Part No. SP Description 2-249-307-01 s INDICATOR, REMOTE 4-734-404-01 s CD-ROM PACK HXCU-FB80...

  • Page 95: Diagrams

    +1.25V REG +1.25V +2.5V REG +2.5V-SDI +1.2V IC107 +1.2V +1.5V REG +1.5V IC112 IC109 +1.8V REG +1.8V VTT/VREF REG +0.75V IC105 +1.05V REG +1.05V-A IC118 +2.0V REG +2.0V IC114 IC120 +1.8V REG +1.8V-A IC115 +2.5V REG +2.5V +1.2V REG +1.2V-A HXCU-FB80...
  • Page 96 CLK148M N DRIVER DPR-386(1/2) IC2524(3/3) IC2538 IC2540 PANEL RESET IC2509 IC2539 IC2543,X2501 IC319,320 27M-CLK-AT 27M-CLK-844 IC2544 IC2541 SD-REF COMPARATE H-PHASE PHASE 27M-CLK-SDI 27M-CLK-ENCODER for SD ADJ.(SD) COMP.(SD) DRIVER 27M-CLK-FPGA-POST 27M-CLK-DA-COMPOSITE 27M-CLK-FPGA-SY 27M-CLK-PROCYON IC2505 IC2506 EXT-REF-SC COMPARATE for SC DPR-386(1/2) HXCU-FB80...

  • Page 97: Frame Wiring

    RET-1 IN SYNC OUT PIX OUT VBS-2 OUT VBS-1 OUT LED-544 SHUTTER (25P) INTERCOM/ MASTER TALLY/PGM GAIN CN804 SDIOUT 4 CN803 SDIOUT 3 CN802 SDIOUT 2 CN801 SDIOUT 1 CN2301 EPR2 CN1501 CN600 PROMPTER_IN EPR2 CN2501 REF_IN Frame Wiring HXCU-FB80...

  • Page 99: Revision History

    Revision History Date History Contents 2018. 1 1st Edition ― 9-932-587-01 HXCU-FB80...
  • Page 102 Printed in Japan Sony Corporation HXCU-FB80 (SY) J, E 2018. 1 08 9-932-587-01 © 2018...

Table of Contents