Center control panel pack for sony mks-9011; sony mks-9012; sony mks-8011; sony mks-8031tb; sony mks-8032; sony mks-8033; sony mks-8035; sony mks-8041; sony mks-8075; sony swc-5002; sony swc-5005; sony swc-5010 (40 pages)
Page 1
HD CAMERA CONTROL UNIT HXCU-FB70 FIBER CONNECTOR KIT HKC-LC02 SERVICE MANUAL 1st Edition...
Page 2
Pour toute réparation faire appel à une personne compétente uniquement. 安全のために,周辺機器を接続する際は,過大電圧を持 つ可能性があるコネクターを以下のポートに接続しない でください。 : LAN コネクター 上記のポートについては本書の指示に従ってくだい。 For safety, do not connect the connector for peripheral device wiring that might have excessive voltage to the following port(s). : LAN connector Follow the instructions for the ports(s). HXCU-FB70...
Page 3
Kasser batteriet i henhold til gjeldende avfallsregler. oder einen gleichwertigen Typ ersetzen. Wenn Sie die Batterie entsorgen, müssen Sie die Gesetze der jeweiligen Region und des jeweiligen Landes befolgen. For kundene i Norge Dette utstyret kan kobles til et IT-strømfordelingssystem. HXCU-FB70...
Page 4
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION The use of optical instruments with this product will increase eye hazard. The HXCU-FB70 is classified as a CLASS 1 LASER PRODUCT. HXCU-FB70...
Manual Structure Purpose of this manual This manual is the service manual for HD Camera Control Unit HXCU-FB70. This manual describes the information items that premise the service based on the components parts such as main parts replacement, electrical alignment, schematic diagrams, board layouts and detailed parts list assuming use of system and service engineers.
Installation 1-1. Power Cord To get a power cord, please contact your local Sony Sales Office/Service Center. WARNING • Use the approved Power Cord (3-core mains lead)/Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if applicable.
VBS 1.0 V p-p, 75 Ω TMDS_DATA1 + SYNC HD: BTA-S001A, tri-level sync , 0.6 V p-p, 75 TMDS_DATA1_ — Ω SHIELD SD: composite sync, 0.3 V p-p, 75 Ω TMDS_DATA1 – HD SYNC/SD SYNC selectable TMDS_DATA0 + Continued HXCU-FB70...
Page 13
MIC IN (Y) (CARBON UNBALANCE) -40 dBu INTERCOM 9. REMOTE (ECM, UNBALANCE) MIC IN (X) -60 dBu 8-pin, Female (DYNAMIC,BALANCE/UNBAL- ANCE) GND for INTERCOM INTERCOM L 8 dBu (VR Max, 250 Ω Load) - External View - Continued HXCU-FB70...
Page 14
TRUNK Data in OFF : OPEN G TALLY (Y) IN TX (+) TRUNK Data out No connection — No connection No connection No connection Continued When the intercom system is set to Clear-Com or RTS, (X) and (G) become input/output pins. HXCU-FB70...
LAN cable (commercially avail- able, shield type, category 5 or higher) INTERCOM 1-2-3. Connection Connectors/Cables Connection made with the connector panels during installation or service, should be made with the connectors/complete cable assemblies specified in the following list, or equivalent parts. HXCU-FB70...
MENU SHUTTER MASTER GAIN ALARM PANEL MIC-ON ACTIVE BARS STANDARD OPEN PROD DISP CANCEL AUTO IRIS/MB ACTIVE POWER MENU ENTER DOWN DOWN IRIS POWER LOCK CONTROL CUSTOM PRESET WHITE BLACK/FLARE MASTER BLACK WHITE CALL AUTO BLACK NETWORK Unit: mm HXCU-FB70...
Lit green: The inserted memory stick can be re- moved. D1001 CONF DONE Lights when there is a problem with the configu- ration of any FPGA (IC1000) on the AT-191 board. DPR-337F board D701 D114 D400 DPR-337F board (Side A) HXCU-FB70...
PLD VerUp Used to enable PLD upgrade using a memory stick. NORMAL/DEBUG Not used NORMAL/DEBUG Not used When this switch is set to ON, the software is automatically upgraded during the power-on process of the CCU. HXCU-FB70...
Clear-Com is connected. RV1802 ENG RTS CANCEL Adjusts sidetone cancellation amount of the engineer line when RTS or Clear-Com is connected. RV2501 27M FREQ Adjusts free-running oscillation frequency of 27M-VCO (X2501) for read- justment required when it is replaced. 1-10 HXCU-FB70...
LC02. Note • When attaching the connector plate (LEMO), pay attention to the position of the red mark on the optical connector (LEMO). Connector plate (LEMO) Boss Optical connector (LEMO) Boss Red mark Bosses Attached screws Attached screws 1-11 HXCU-FB70...
Page 22
• Do not bend any optical fiber cable to an extent of R = 30 or less. • Before connecting an optical fiber cable, clean its end. • When installing , arrange the optical fiber cable as shown in the figure. PS-862 board Optical fiber cables AT-191 board Harness “2” Clamp1 “1” 1-12 HXCU-FB70...
Page 23
“5-3. PS Cover”) Note When installing the PS cover, do not catch the optical fiber cable. Install the top cover. (Refer to “5-1. Top Cover”) Note When installing the top cover, do not catch the optical fiber cable. 1-13 HXCU-FB70...
When the slide rail 305A-18 is used. • Slide rail: 1 set Accuride Japan Model 305A-18 (457 mm) • Front bracket: 2 Sony Part No.: 2-142-214-01 • Rear bracket: 2 Sony Part No.: 2-142-215-01 • Screw (B4 x 8): 14 •...
Page 25
(1U) of the unit. Inner rail Inner rail Other equipment 0.5U 1.5U HXCU-FB70 1.5U HXCU-FB70 0.5U Other equipment When mounting this unit above other equipment, install the inner rail at the lower part (1U) of the unit.
Page 26
• When attaching the rear bracket, adjust the bracket position according to the depth of the rack. Plate nut Rear bracket B4 x 8 Front bracket Cabinet member Mid member B4 x 8 Front bracket Mid member B4 x 8 1-16 HXCU-FB70...
Page 27
Attach the rear bracket to the outside of the rack mount position with four screws (B5 x 8). Rack (rear) Outer rail B5 x 8 B5 x 8 31.75 Rear bracket Unit: mm 1-17 HXCU-FB70...
(1U) of the unit. Inner rail Inner rail Other equipment 0.5U 1.5U This unit 1.5U This unit 0.5U Other equipment When mounting this unit above other equipment, install the inner rail at the lower part (1U) of the unit. 1-18 HXCU-FB70...
Page 29
Attach the front and rear brackets to the outer rail with eight screws (B4 x 8) and four plate nuts. Note • When attaching the rear bracket, adjust the bracket position according to the depth of the rack. Rear bracket Plate nuts Outer rail Front bracket B4 x 8 1-19 HXCU-FB70...
Page 30
Attach the rear bracket to the outside of the rack mount position with four screws (B5 x 8). Rack (rear) B5 x 8 Outer rail B5 x 8 31.75 Rear bracket Unit: mm 1-20 HXCU-FB70...
Page 31
• Failure to tighten the rack angle screws may cause the unit to slide and fall from the rack, resulting in injury. After the unit has been mounted, be sure to tighten all the screws. Rack Rack angle PSW5 x 25 Inner rail PSW5 x 25 Rack angle 1-21 HXCU-FB70...
BATTERY, LITHIUM (CR2032 For real time clock (RTC) backup 1-528-174-33 TYPE) CAUTION In replacing, ensure that the battery is installed with “+” and “-” poles connected to the correct terminals. Improper connection may cause an explosion or leakage of fluid. HXCU-FB70...
Do not open the connector open/close section 90 degrees or more so as not to damage the connector. Pull the flexible card wire. Connection Insert the flexible card wire fully into the connector. Push the connector open/close section to lock the flexible card wire. HXCU-FB70...
Do not open the connector open/close section 90 degrees or more so as not to damage the connector. Pull the flexible card wire. Connection Insert the flexible card wire fully into the connector. Push the connector open/close section to lock the flexible card wire. HXCU-FB70...
Copy the upgrading program to the Memory Stick in the following steps. Note To get the upgrading program (program files “HXCUFB70.rom” and “HXCUFB70_BOOT.rom”), contact your local Sony Sales Office/Service Center. Make the following directory on the Memory Stick. \MSSONY\PRO\CAMERA\HXCUFB70 Copy the program files “HXCUFB70.rom” and “HXCUFB70_BOOT.rom” to the directory made in step 1.
Copy the upgrading program to the Memory Stick in the following steps. Note To get the upgrading program (program files “HXCUFB70.rom” and “HXCUFB70_BOOT.rom”), contact your local Sony Sales Office/Service Center. Make the following directory on the Memory Stick. \MSSONY\PRO\CAMERA\HXCUFB70 Copy the program files “HXCUFB70.rom” and “HXCUFB70_BOOT.rom” to the directory made in step 1.
Save the upgrading boot program in the ROMs H (IC2) and L (IC3) on the ROM-28 board. Note For details of saving the upgrading program, contact your local Sony Sales Office/Service Center. Remove the top cover. (Refer to Section 5-1.) Connect the connector CN1 on the ROM-28 board to the connector CN103 on the AT-191 board.
Page 39
Preparation Copy the upgrading program to the Memory Stick in the following steps. Note To get the upgrading program (program file “hdmi-firmware.rom”), contact your local Sony Sales Office/Service Center. Make the following directory on the Memory Stick. \MSSONY\PRO\CAMERA\HXCUFB70 Copy the program file “hdmi-firmware.rom” to the directory made in step 1.
This unit is provided with programmable logic devices (PLDs). They can be programmed and reprogrammed by the MAIN program. If the parts listed below needs to be replaced or if PLD needs to be upgraded, contact your local Sony Sales Office/ Service Center.
Page 41
Turn off the power and remove the Memory Stick. When the unit is turned on, the PLD is upgraded and runs. Check that the main program has been upgraded with “AT Diag and DPR Diag” of status display. (Refer to the Operating Instructions.) HXCU-FB70...
The replacement period of each part depends on the environment and condition. Refer to “5. Replacement of Main Parts” for the replacement method of parts. Part name Part No. Check/replacement period FAN, DC (60 SQUARE) Replace every two years (When used for eight hours a day.) 1-855-252-11 2-10 HXCU-FB70...
The table below lists data retained in the EEPROM on respective boards. Note The part number listed in “Spare Parts” is for EEPROM which is not programmed. Therefore, program a new EEPROM after replacement. For details, contact your local Sony Sales Office/Service Center. Board name Ref. No.
While pushing the shell, clean the tip of the white optical contacts using the optical connector cleaner. Note The sealing shutter is released while the shell is being pushed. Optical contacts (white) Shell Male connector Optical connector cleaner 2-13 HXCU-FB70...
Page 46
Cleaning of male connector While pushing the shell, clean the tip of the white optical contacts with a cotton swab moistened with alcohol. Note The sealing shutter is released while the shell is being pushed. Optical contacts (white) Shell Male connector 2-14 HXCU-FB70...
Optical contacts (white) Cleaning of female connector Insert the optical connector cleaner straight. Ensure that it is held straight when inserting. Apply sufficient pressure to ensure that the optical contact is a little depressed. (approximately 600 g to 700 g) 2-15 HXCU-FB70...
Page 48
Tool and fixtures • Alignment sleeve remover HC-001 (for female connector) Sony Part No. : J-6480-010-A or DCC.91.312.5LA manufactured by LEMO, or equivalent Note Insert the shorter nose end when removing/installing the alignment sleeve. Grasp not the shock absorber portion of the remover but the handle in use.
Page 49
The alignment sleeve can be removed/reinstalled with the sleeve itself attached to the tip of the remover. Great care should be taken so as not to lose or damage the alignment sleeve. Alignment sleeve: Sony Part No. : 9-980-074-01 Alignment sleeve Clean the tip of the white optical contacts with a cotton swab moistened with alcohol.
The CCU has a function for detecting optical signal reception status and displaying the reception status of the CCU and the camera adapter on the OPTICAL CONDITION LED on the front panel. The light receiving 2-18 HXCU-FB70...
Page 51
(IC900) and the superimposed signal is converted to an HDMI signal by the transceiver (IC1000) for transmission. Then the HDMI signal is output from the rear panel of the CCU. Return channel video signals The following processing is applied to each of the return channel video signals from the rear panel. 2-19 HXCU-FB70...
Front Panel Block The front panel block consists of boards SW-1572, LED-518, LED-519, and CN-3583. These boards contain system setup switches, a potentiometer control circuit, a display circuit, an INCOM system interface circuit, and a CCU MENU operation circuit. 2-21 HXCU-FB70...
Page 54
This board contains a TALLY (red/green) LED. Indication of this LED is controlled from the SW-1572 board through a flexible flat cable. CN-3583 board This board contains an INCOM connector (XLR-5 female) to be connected to the input amplifier on the SW-1572 board with a harness. 2-22 HXCU-FB70...
• The ordinary soldering iron can be used but the iron tip has to be applied to the solder joint for a slightly longer time. The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful. 2-23 HXCU-FB70...
*: The maximum transmission distance is 10 km (32,800 ft) when a general single-mode optical fiber cable with an LC connector is used. If the unit is connected only with the single-mode optical fiber cable, no power can be supplied from the HXCU-FB70.
*2: The maximum transmission distance is 10 km (32,800 ft) when a general single-mode optical fiber cable with an LC connector is used. When using a Sony’s hybrid fiber cable CCFN-25/50/100 or an SMPTE cable (LEMO’s connector), confirm that the input AC power line of the HXCE-FB70 and HXCU-FB70 is securely grounded.
Re-set the C07: SIDE TONE value of the CCU CONFIGURATION menu to the customer settings. RV1801 RV1802 DPR-337F board (Side A) The producer line is always mixed with the engineer line at the camera side. HXCU-FB70...
Page 61
C07: PGM LEVEL of the CCU CONFIGURATION menu. Selecting Intercom Line to Be Connected to the INTERCOM Connector Select the intercom line to be connected to the front INTERCOM connector as follows with the INTERCOM switch. Producer line: PROD Engineer line: ENG HXCU-FB70...
20, 30, 40, 50, 60 dB Note Maintenance menu → Camera → Microphone Gain Setting Audio Output Level Set the Audio outputs (CH-1 and CH-2) with C05: MIC/AUDIO according to each signal level. -20 dB, 0, or +4 dB (factory setting: 0 dB) HXCU-FB70...
This unit supports red tally and green tally systems. Only contact supply input is supported. The output is open collector (Max. 30 mA). 3-3-2. Camera Number Setting Set the camera number with N03: CCU NO of the NETWORK SETTINGS menu. (Refer to the Operating Instructions.) HXCU-FB70...
Crops 15 : 9 (or 14 : 9 or 13 : 9) video part from the HD video signal, fits it into a 4 : 3 monitor frame, and then converts it to SD signal (4 : 3) (Black level is inserted above and below the picture.) HXCU-FB70...
Page 65
Horizontal cutting position of 4 : 3 (12 : 9) Picture whose aspect ratio is converted (SD output) Edge-crop CROP POSITION can be changed. Squeeze The 16 : 9 ratio picture is output in the SD format without changing the ratio. HXCU-FB70...
The picture that is cut out with the aspect ratio of 13 : 9, is inserted into the 4 : 3 ratio picture and is output in the SD format. 3-4-4. VBS Signal Level Adjustment Adjust the VBS signal level that is output from this unit using the CCU color-bar signal. Note Set the intercom system with MAINTENANCE menu. (Refer to the Operating Instructions.) 3-10 HXCU-FB70...
Turn the CANCEL/ENTER lever quickly to the CANCEL side twice. Changing Setting Values To enter: Press the CONTROL knob. To cancel: Turn the CANCEL/ENTER lever to the CANCEL side before pressing the CONTROL knob. The setting of the selected item is restored. HXCU-FB70...
Turn the DISP/MENU lever to the MENU side. The menu disappears. To restart the setting operation, turn the DISP/ MENU lever again to the MENU side. 4-1-2. Memory Stick The following types of Memory Stick are available for this unit. • Memory Stick Duo • Memory Stick PRO Duo (Up to 2 GB) HXCU-FB70...
Menu screen Item Description STORE FILE Registers the current adjustment values as an < O H B F I L E > V 0 3 T O P → OHB file. S T O R E F I L E HXCU-FB70...
Page 72
±99 F L A R E V M O D O N D . S H A D : O F F FLARE ON/OFF T E S T : O F F V MOD ON/OFF D.SHAD ON/OFF TEST OFF/1/2 HXCU-FB70...
Page 73
KNEE SAT ±99 A U T O K N E E : O F F ON/OFF P O I N T L I M I T : S L O P E AUTO KNEE OFF/AUTO POINT LIMIT ±99 SLOPE ±99 HXCU-FB70...
Page 74
L I M I T E R [ M ] : [WHT] ±99 [ W H T ] : [ B L K ] : C R I S P [BLK] ±99 L V L D E P CRISP ±99 LEVEL DEP ±99 ON/OFF HXCU-FB70...
Page 75
S H U T T E R : O F F ECS FREQ : 1 / 1 0 0 E C S F R E Q : 6 0 . 0 0 H z ON/OFF E V S : O F F HXCU-FB70...
Page 76
L I M I T E R [ M S T ] : [WHT] ±99 [ W H T ] : [ B L K ] : [BLK] ±99 C R I S P CRISP ±99 HXCU-FB70...
Page 77
M U L T I M A T R I X : O F F SATURATION ±99 Adjusts the SD multi-matrix correction value of saturation for each PHASE (16 angles). ALL PRESET MATRIX ON/OFF PRESET MATRIX ON/OFF MULTI MATRIX ON/OFF HXCU-FB70...
Page 78
I R I S L E V E L : A P L R A T I O : I R I S G A I N : AUTO IRIS ON/OFF A U T O I R I S : O F F 4-10 HXCU-FB70...
Page 79
AUTO LEVEL — LEVEL AUTO: EX- LEVEL AUTO: LEVEL AUTO: LEVEL AUTO: ECUTING BREAK AUTO WHITE — AWS: EXECUTING AWS: OK AWS: NG AWS: BREAK SHADING AUTO BLACK — ABS: EXECUTING ABS: OK ABS: NG ABS: BREAK SHADING 4-11 HXCU-FB70...
Page 80
M O N O C O L O R : O F F to 90 when the rotary encoder is rota- P H A S E S A T U R A T I O N : ted clockwise. SATURATION ±99 4-12 HXCU-FB70...
→ the EEPROM (IC309) on the NAME HXCU-FB70 DPR-337F board. S E R I A L N O : 0 0 0 0 0 0 0 0 N A M E : H X C U - F B 7 0...
Page 82
HDMI version information. A L L Upgrades all ROM files stored in the Memory A U T O Stick. AUTO Upgrades only files later than the current version of relevant ROMs in the Memory Stick. 4-14 HXCU-FB70...
Page 83
COMPONENT LEVEL RGB/YCD ADJ PR/R/R-Y BAL ADJ PB/B/B-Y BAL ADJ WRITE Writes the above cropping setting values to the EE- PROM. CLEAR Clears the above adjustment values. 4-15 HXCU-FB70...
Page 84
Y C C ( E 5 ) : P-A(E2) Progressive Audio Latency. S A L ( E 6 ) : I-V(E3) Interlaced Video Latency. I-A(E4) Interlaced Audio Latency. EDID EDID information of connected device. 4-16 HXCU-FB70...
This section describes replacement methods for periodic replacement parts, main mechanical parts, and mount boards. 5-1. Top Cover Procedure Remove the seven screws to detach the top cover. PSW3 x 6 PSW3 x 6 PSW3 x 6 Top cover Install the removed parts by reversing the steps of removal. HXCU-FB70...
Disconnect the flexible flat cable (45 core) from the connector (CN3) on the SW-1572 board. Remove the four screws to detach the front panel assembly. Front panel assembly PSW3 x 6 PSW3 x 6 Flexible flat cable (45 core) SW-1512 board Install the removed parts by reversing the steps of removal. HXCU-FB70...
PS Cover Preparation Remove the top cover. (Refer to “5-1. Top Cover”) Procedure Remove the three screws to detach the PS cover. PSW3 x 6 PSW3 x 6 PS cover Install the removed parts by reversing the steps of removal. HXCU-FB70...
Disconnect the five harnesses from the five connectors (CN2, CN5, CN1, CN3 and CN4) on the PS-862 board. Harnesses PS-862 board Harnesses Remove the four screws to detach the PS-862 board. PSW3 x 6 PSW3 x 6 PS-862 board Install the removed parts by reversing the steps of removal. HXCU-FB70...
Procedure Open the edge saddle. Disconnect the harness from the connector (CN4) on the PS-862 board. Remove the screw to detach the fan assembly. PSW3 x 6 Fan assembly Harness CN4 (PS-826 board) Edge saddle Remove the fan duct. HXCU-FB70...
Page 90
Remove the fan cushion from the fan. Label Fan duct Fan cushion Harness Notes • Attach the fan positioning as shown in the figure. • Route the fan harness properly as shown in the figure. Install the removed parts by reversing the steps of removal. HXCU-FB70...
Remove the four screws to detach the switching regulator (large). Remove the slide sheet and the heat conductive sheet PS-1 from the switching regulator (large). PSW3 x 6 Slide sheet Connector Switching regulator (large) PSW3 x 6 Heat conductive sheet PS-1 Harness Connectors Harnesses Install the removed parts by reversing the steps of removal. HXCU-FB70...
Remove the four screws to detach the switching regulator (small). PSW3 x 6 PS bracket PSW3 x 6 Insulating sheet PS-B PSW3 x 6 Connector Harness Switching regulator (small) Harness Connector Install the removed parts by reversing the steps of removal. HXCU-FB70...
Cover”) Procedure Remove the lithium battery. Disconnect the three flexible flat cable (45 core) from the connector (CN1, CN2 and CN600) on the AT-191 board. Open the clamp. Disconnect the harness from the connector (CN2) on the AT-191 board. HXCU-FB70...
Page 94
• Do not bend any optical fiber cable to an extent of R = 30 or less. • Before connecting an optical fiber cable, clean its end. • When installing, arrange the optical fiber cable as shown in the figure. Install the removed parts by reversing the steps of removal. 5-10 HXCU-FB70...
• When installing, arrange the the optical fiber cable as shown in the figure. Remove the two screws (PSW3 x 6) to detach the bracket from the rear panel. Remove the two screws (K3 x 6) to detach the Neutrik fiber cap and the optical connector assembly. 5-11 HXCU-FB70...
Page 96
• When installing the bracket, fit the four bosses with the four holes. • When connecting an optical cable, not to mistake the orientation of the optical connector assembly and the cable connecting position. Install the removed parts by reversing the steps of removal. 5-12 HXCU-FB70...
Remove the seven screws (2.6 x 6) and the four screws (BVTT2.5) to detach the CN-3556 board. CN-3356 board Flexible flat cable (45 core) BVTT2.5 BVTT2.5 2.6 x 6 Install the removed parts by reversing the steps of removal. 5-13 HXCU-FB70...
Disconnect the flexible flat cable (10 core) from the connector (CN2) on the CN-3582 board. Remove the two attached hexagon screws to detach the CN-3582 board. CN-3582 board Flexible flat cable (10 core) Attached hexagon screws Install the removed parts by reversing the steps of removal. 5-14 HXCU-FB70...
PSW3 x 6 Harness CN-3383 board Remove the two screws to detach the INCOM plate from the CN-3584 board. INCOM plate CN-3383 board BTP3 x 10 BTP3 x 10 Install the removed parts by reversing the steps of removal. 5-15 HXCU-FB70...
Remove the two screws to detach the CN-3583 board. Disconnect the harness from the connector (CN2) on the CN-3583 board. CN-3584 board BVTT2.5 x 6 Harness AT-191 board BVTT2.5 x 6 Install the removed parts by reversing the steps of removal. 5-16 HXCU-FB70...
Remove the two attached hexagon screws, four screws (2.6 x 6), three screws (PSW3 x 6) and the two screws (BTP3 x 10) to detach the nut plate and the DPR-337F board. PSW3 x 6 AT bracket PSW3 x 6 Nut plate PSW3 x 6 DPR-337F board Attached hexagon screws 2.6 x 6 PSW3 x 6 BTP3 x 10 Install the removed parts by reversing the steps of removal. 5-17 HXCU-FB70...
Remove the screw to detach the LED-518 board. PSW3 x 6 LED-518 board Holes Bosses Note When installing the LED-518 board, fit the two bosses with the two holes. Install the removed parts by reversing the steps of removal. 5-18 HXCU-FB70...
Page 103
Disconnect the flexible flat cable (10 core) from the connector (CN1) on the LED-519 board. Remove the screw to detach the LED-519 board. PSW3 x 6 LED-519 board Flexible flat cable (10 core) Install the removed parts by reversing the steps of removal. 5-19 HXCU-FB70...
Volume assembly knob (large) Disconnect the flexible flat cable (10 core) from the connector (CN4) on the SW-1572 board. Disconnect the harness from the connector (CN1) on the SW-1572 board. Remove the eight screws to detach the SW-1572 board. 5-20 HXCU-FB70...
Page 105
• When installing the SW-1572 board, tighten the screw (a) first while pushing the SW-1572 board in the arrow direction. SW-1572 board • When installing the SW-1572 board, arrange the harness under the CN-3584 board. CN-3583 board Harness Install the removed parts by reversing the steps of removal. 5-21 HXCU-FB70...
Connection of Equipment Note Transmittable Optoelectrical composite cable: CCFN-25/50/100 Audio oscillator HD color camera HXC-D70 Signal HD camera control unit generator Optoelectrical HXCU-FB70 REFERENCE composite cable /DPR-337F Waveform monitor CCA-5 cable (max. 50 m) PIX/CN-3556 75 Ω 75 Ω Remote control panel...
M01: SERIAL NO SET → DEST → UC/J/CE • CCU CONFIGURATION menu C07: INCOM MIC → CARBON • Front panel INTERCOM switch → PROD Except for these settings, do not change the switch settings made when the unit was shipped. (Refer to Section 1-5-2.) HXCU-FB70...
COMPONENT LEVEL Adjustment Y signal level adjustment Equipment: Analog HD waveform monitor Test Point: Y connector / rear panel Adjusting Point: MAINTENANCE menu → M05: COMPONENT LEVEL → RGB/YCD TRIM Specification: A = 700 ± 5 mV (75 Ω termination) HXCU-FB70...
RGB Output Level Adjustment Preparation SYSTEM OPERATION menu setting Page name Item Settings S04: OUTPUT FORMAT COMPONENT HD RGB CCU CONFIGURATION menu setting Page name Item Settings C01: COLOR BAR HD BAR BAR 16:9 (100%) C09: VIDEO ADJUST COMPONENT LEVEL HXCU-FB70...
Page 115
Test Point: B connector / rear panel Adjusting Point: MAINTENANCE menu → M05: COMPONENT LEVEL → PB/B/B-Y BAL TRIM Specification: C = 700 ± 5 mV p-p (75 Ω termination) After these adjustments are completed, select "WRITE" to store the setting values. HXCU-FB70...
Therefore, specified parts should be used in the case 指定の部品を使ってください。 of replacement. 2. Standardization of Parts 2. 部品の共通化 Some repair parts supplied by Sony differ from those ソニーから供給する補修用部品は,セットに使われ used for the unit. These are because of parts common- ているものと異なることがあります。 ality and improvement.
1-967-975-11 s HARNESS, SUB (CCU DC OUT) 1-967-976-11 s HARNESS, SUB (POWER CONT) 2-580-644-01 s SCREW, +KTP2 3X8 4-299-617-01 s COVER 4-299-632-01 s RACK BRACKET(U) 4-299-661-01 s RACK BRACKET COVER 4-382-854-51 s SCREW (M3X6), P, SW (+) 7-682-949-01 s SCREW +PSW 3X10 HXCU-FB70...
Page 119
A-1903-509-A s MOUNTED CIRCUIT BOARD, PS-862 1-474-293-11 s REGULATOR, SWITCHING 1-474-316-11 s REGULATOR, SWITCHING 1-967-974-11 s HARNESS, SUB (DC OUT) 4-299-621-01 s SHEET, HEAT CONDUCTIVE PS-1 4-299-631-01 s SHEET, HEAT CONDUCTIVE PS-2 4-382-854-51 s SCREW (M3X6), P, SW (+) HXCU-FB70...
Page 120
1-528-174-72 s BATTERY, LITHIUM (CR2032 TYPE) 1-831-081-11 s CABLE, FLEXIBLE FLAT (45 CORE) 1-846-443-11 s CABLE, LC-LC 4-382-854-51 s SCREW (M3X6), P, SW (+) 4-444-729-01 s CAP, NEUTRIC FIBER 7-682-949-01 s SCREW +PSW 3X10 7-682-247-04 s SCREW +K 3X6 HXCU-FB70...
Page 121
1-836-689-11 s CABLE, FLEXIBLE FLAT (10 CORE) 2-580-628-01 s SCREW, +BVTP S3X6 TYPE2 3-637-901-02 s SCREW M2.6X5 3-776-750-02 s SCREW +BVTT 2.5(S) 3-853-802-01 s CLAMP, REUSE 4-382-854-51 s SCREW (M3X6), P, SW (+) 7-685-547-14 s SCREW +BTP 3X10 TYPE2 N-S HXCU-FB70...
Page 122
1-855-252-11 s FAN, DC (60 SQUARE) 1-967-973-11 s HARNESS (AC IN) 2-990-241-02 s HOLDER (A), PLUG 3-257-200-01 s CLAMP, CORD 4-139-239-01 s FAN CUSHION 4-382-854-51 s SCREW (M3X6), P, SW (+) 7-682-949-01 s SCREW +PSW 3X10 7-682-961-01 s SCREW +PSW 4X8 HXCU-FB70...
Page 123
X-3704-947-2 s KNOB ASSY (S) 3-872-590-01 s PORONSHEET (POWER) 1-836-689-11 s CABLE, FLEXIBLE FLAT (10 CORE) 2-139-192-01 s FRAME, INDICATOR WINDOW 2-139-193-02 s WINDOW, INDICATOR 7-685-547-14 s SCREW +BTP 3X10 TYPE2 N-S 2-249-353-01 s COVER, LAMP 3-725-295-21 s SCREW, (+) (B3) HXCU-FB70...
1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 C162 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C163 1-114-238-91 s CAP, CERAMIC 22MF B 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 HXCU-FB70...
Page 125
1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C508 1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225 C709 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C509 1-164-858-81 s CAP, CHIP CERAMIC 22PF CH 1005 C710 1-112-717-91 s CAP, CERAMIC 1UF B (1005) HXCU-FB70...
Page 126
1-112-717-91 s CAP, CERAMIC 1UF B (1005) C1009 1-112-717-91 s CAP, CERAMIC 1UF B (1005) C1074 1-112-717-91 s CAP, CERAMIC 1UF B (1005) C1010 1-112-717-91 s CAP, CERAMIC 1UF B (1005) C1075 1-112-717-91 s CAP, CERAMIC 1UF B (1005) 7-10 HXCU-FB70...
Page 127
8-719-083-60 s DI UDZSUSTE-174.7B FB513 1-469-094-21 s FERRITE, EMI (SMD) (1608) D501 8-719-083-60 s DI UDZSUSTE-174.7B FB800 1-414-554-21 s FERRITE, EMI (SMD) (1608) D502 6-501-123-01 s DIODE RB160M-60TR FB801 1-414-554-21 s FERRITE, EMI (SMD) (1608) D503 6-502-197-01 s DI SML-D12M8WT86SM 7-11 HXCU-FB70...
Page 128
1-400-788-21 s INDUCTOR, CHIP 1.0UH (2518) L704 1-400-791-21 s INDUCTOR, CHIP 10UH (2518) IC326 6-702-319-01 s IC TC7WZ04FK L705 1-400-791-21 s INDUCTOR, CHIP 10UH (2518) IC500 6-712-135-01 o IC R1173H001D-T1-FE L706 1-400-791-21 s INDUCTOR, CHIP 10UH (2518) IC501 6-706-220-01 s IC LTC3411EMS#TR 7-12 HXCU-FB70...
Page 129
1-220-230-91 s RES,SQUARE TYPE CHIP 2.2(3225) R142 1-208-911-81 s RES, CHIP 10K (1005) 1-208-935-81 s RES, CHIP 100K (1005) R143 1-208-911-81 s RES, CHIP 10K (1005) 1-208-955-81 s RES, CHIP 680K (1005) R144 1-208-935-81 s RES, CHIP 100K (1005) 7-13 HXCU-FB70...
Page 130
1-211-986-91 s RES, CHIP 51 (1608) R548 1-208-903-81 s RES, CHIP 4.7K (1005) R388 1-218-823-91 s RES, CHIP 100 (1608) R549 1-208-927-81 s RES, CHIP 47K (1005) R389 1-218-823-91 s RES, CHIP 100 (1608) R550 1-208-927-81 s RES, CHIP 47K (1005) 7-14 HXCU-FB70...
Page 131
1-208-907-81 s RES, CHIP 6.8K (1005) R844 1-208-911-81 s RES, CHIP 10K (1005) R731 1-208-895-81 s RES, CHIP 2.2K (1005) R845 1-208-911-81 s RES, CHIP 10K (1005) R732 1-208-887-81 s RES, CHIP 1.0K (1005) R878 1-208-887-81 s RES, CHIP 1.0K (1005) 7-15 HXCU-FB70...
Page 132
1-234-377-21 s RES, NETWORK 4.7K (1005X4) RB328 1-234-369-21 s RES, NETWORK 10 (1005X4) RB101 1-234-377-21 s RES, NETWORK 4.7K (1005X4) RB600 1-234-371-21 s RES, NETWORK 47 (1005X4) RB102 1-234-377-21 s RES, NETWORK 4.7K (1005X4) RB601 1-234-371-21 s RES, NETWORK 47 (1005X4) 7-16 HXCU-FB70...
Page 133
8-729-928-82 s TRANSISTOR DTC144EE-TL Q006 8-729-928-25 s TRANSISTOR 2SA1774TL-QR THP507 1-804-616-21 s THERMISTOR, POSITIVE Q007 8-729-928-28 s TRANSISTOR DTA144EE-TL TP100 1-535-877-22 s CHIP, CHECKER Q008 8-729-928-25 s TRANSISTOR 2SA1774TL-QR TP600 1-535-877-22 s CHIP, CHECKER Q009 8-729-928-25 s TRANSISTOR 2SA1774TL-QR 7-17 HXCU-FB70...
Page 134
1-164-939-81 s CAP, CHIPCERAMIC 2200PF B 1005 or Q'ty Part No. SP Description 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C100 1-100-591-91 s CAP, CHIP CERAMIC 1MF B 2012 A-1903-385-A s MOUNTED CIRCUIT BOARD, CN-3583 C101 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 7-18 HXCU-FB70...
Page 135
1-114-419-21 s CAP, CERAMIC 10MF B (2012) C167 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C239 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C168 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C240 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 7-19 HXCU-FB70...
Page 136
1-112-815-91 s CAP, CERAMIC 10MF C (1608) C333 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C527 1-112-815-91 s CAP, CERAMIC 10MF C (1608) C334 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C528 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 7-20 HXCU-FB70...
Page 137
1-112-717-91 s CAP, CERAMIC 1UF B (1005) C703 1-112-815-91 s CAP, CERAMIC 10MF C (1608) C768 1-112-717-91 s CAP, CERAMIC 1UF B (1005) C704 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C769 1-112-717-91 s CAP, CERAMIC 1UF B (1005) 7-21 HXCU-FB70...
Page 138
1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C853 1-112-717-91 s CAP, CERAMIC 1UF B (1005) C947 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C854 1-112-717-91 s CAP, CERAMIC 1UF B (1005) C948 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 7-22 HXCU-FB70...
Page 139
1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C1122 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C1210 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C1123 1-112-815-91 s CAP, CERAMIC 10MF C (1608) C1211 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 7-23 HXCU-FB70...
Page 140
C1844 1-112-815-91 s CAP, CERAMIC 10MF C (1608) C1388 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C1846 1-112-815-91 s CAP, CERAMIC 10MF C (1608) C1389 1-112-815-91 s CAP, CERAMIC 10MF C (1608) C1849 1-114-214-81 s CAP,CHIP CERAMIC470PF CH1005 7-24 HXCU-FB70...
Page 141
1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225 C1944 1-112-815-91 s CAP, CERAMIC 10MF C (1608) C2009 1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225 C1945 1-112-815-91 s CAP, CERAMIC 10MF C (1608) C2010 1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225 7-25 HXCU-FB70...
Page 142
1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 C2317 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C2384 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C2318 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C2385 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 7-26 HXCU-FB70...
Page 143
1-114-419-21 s CAP, CERAMIC 10MF B (2012) C2577 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C2815 1-112-015-91 s CAP, CHIP CERAMIC 47MF B 3225 C2578 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C2816 1-164-936-81 s CAP, CHIP CERAMIC 680PF B 1005 7-27 HXCU-FB70...
Page 144
1-414-864-21 s FERRITE, EMI (SMD) (1608) D1803 8-719-024-71 s DIODE 1SS362-TE85L D1804 8-719-024-71 s DIODE 1SS362-TE85L FB142 1-414-864-21 s FERRITE, EMI (SMD) (1608) FB143 1-414-864-21 s FERRITE, EMI (SMD) (1608) D1805 8-719-024-71 s DIODE 1SS362-TE85L FB144 1-414-864-21 s FERRITE, EMI (SMD) (1608) 7-28 HXCU-FB70...
Page 145
8-759-592-47 s IC TC7SZ08FU(TE85R) FB1002 1-469-094-21 s FERRITE, EMI (SMD) (1608) IC318 8-759-592-47 s IC TC7SZ08FU(TE85R) FB1003 1-469-094-21 s FERRITE, EMI (SMD) (1608) IC319 6-708-277-01 s IC CDCVF25081PWR FB1004 1-469-094-21 s FERRITE, EMI (SMD) (1608) IC320 6-708-277-01 s IC CDCVF25081PWR 7-29 HXCU-FB70...
Page 146
6-706-484-01 s IC TC7SH04FU IC2316 6-706-488-01 s IC TC7SH14FU IC1116 8-759-669-66 s IC TLC272CPWR-12 IC2317 6-707-850-01 s IC TC74LCX245FT(EKJ) IC1117 6-706-482-01 s IC TC7SH00FU IC2318 6-707-850-01 s IC TC74LCX245FT(EKJ) IC1131 8-759-561-46 s IC AD8014ARTZ-REEL7 IC2319 6-707-850-01 s IC TC74LCX245FT(EKJ) 7-30 HXCU-FB70...
Page 147
1-469-549-21 s INDUCTOR, CHIP 1.0UH (LB2016) L1325 1-414-398-41 s INDUCTOR (SMD) 10.0UH L701 1-469-549-21 s INDUCTOR, CHIP 1.0UH (LB2016) L1501 1-414-398-41 s INDUCTOR (SMD) 10.0UH L702 1-469-549-21 s INDUCTOR, CHIP 1.0UH (LB2016) L1502 1-414-398-41 s INDUCTOR (SMD) 10.0UH 7-31 HXCU-FB70...
Page 148
8-729-928-05 s TRANSISTOR 2SC4617TL-QR Q1825 8-729-928-28 s TRANSISTOR DTA144EE-TL Q105 8-729-054-35 s TRANSISTOR HAT2070R-EL Q1826 8-729-928-28 s TRANSISTOR DTA144EE-TL Q106 8-729-054-35 s TRANSISTOR HAT2070R-EL Q1827 8-729-928-25 s TRANSISTOR 2SA1774TL-QR Q107 6-550-631-01 s TRANSISTOR 2SA1797-T100-Q Q1828 8-729-928-05 s TRANSISTOR 2SC4617TL-QR 7-32 HXCU-FB70...
Page 149
1-208-911-81 s RES, CHIP 10K (1005) R172 1-208-935-81 s RES, CHIP 100K (1005) R102 1-208-863-81 s RES, CHIP 100 (1005) R173 1-218-990-81 s CONDUCTOR, CHIP (1005) R104 1-208-911-81 s RES, CHIP 10K (1005) R174 1-208-911-81 s RES, CHIP 10K (1005) 7-33 HXCU-FB70...
Page 150
1-218-990-81 s CONDUCTOR, CHIP (1005) R358 1-220-878-81 s RES, CHIP 22 (1005) R274 1-220-230-91 s RES,SQUARE TYPE CHIP 2.2(3225) R359 1-208-887-81 s RES, CHIP 1.0K (1005) R276 1-208-927-81 s RES, CHIP 47K (1005) R360 1-208-919-81 s RES, CHIP 22K (1005) 7-34 HXCU-FB70...
Page 151
1-208-863-81 s RES, CHIP 100 (1005) R672 1-208-903-81 s RES, CHIP 4.7K (1005) R511 1-208-863-81 s RES, CHIP 100 (1005) R673 1-208-903-81 s RES, CHIP 4.7K (1005) R518 1-208-939-81 s RES, CHIP 150K (1005) R675 1-208-911-81 s RES, CHIP 10K (1005) 7-35 HXCU-FB70...
Page 152
1-208-883-81 s RES, CHIP 680 (1005) R900 1-218-990-81 s CONDUCTOR, CHIP (1005) R825 1-208-887-81 s RES, CHIP 1.0K (1005) R901 1-208-911-81 s RES, CHIP 10K (1005) R826 1-208-887-81 s RES, CHIP 1.0K (1005) R902 1-220-878-81 s RES, CHIP 22 (1005) 7-36 HXCU-FB70...
Page 153
1-208-927-81 s RES, CHIP 47K (1005) R1153 1-208-911-81 s RES, CHIP 10K (1005) R1025 1-208-871-81 s RES, CHIP 220 (1005) R1154 1-208-875-81 s RES, CHIP 330 (1005) R1026 1-218-990-81 s CONDUCTOR, CHIP (1005) R1157 1-208-927-81 s RES, CHIP 47K (1005) 7-37 HXCU-FB70...
Page 154
1-208-903-81 s RES, CHIP 4.7K (1005) R1310 1-208-863-81 s RES, CHIP 100 (1005) R1228 1-208-899-81 s RES, CHIP 3.3K (1005) R1311 1-208-863-81 s RES, CHIP 100 (1005) R1229 1-208-895-81 s RES, CHIP 2.2K (1005) R1312 1-208-935-81 s RES, CHIP 100K (1005) 7-38 HXCU-FB70...
Page 155
1-208-919-81 s RES, CHIP 22K (1005) R1478 1-208-867-81 s RES, CHIP 150 (1005) R1399 1-208-911-81 s RES, CHIP 10K (1005) R1479 1-208-867-81 s RES, CHIP 150 (1005) R1400 1-208-903-81 s RES, CHIP 4.7K (1005) R1480 1-208-867-81 s RES, CHIP 150 (1005) 7-39 HXCU-FB70...
Page 156
1-220-870-81 s RES, CHIP 10 (1005) R1945 1-208-863-81 s RES, CHIP 100 (1005) R1828 1-208-915-81 s RES, CHIP 15K (1005) R1946 1-208-863-81 s RES, CHIP 100 (1005) R1829 1-208-915-81 s RES, CHIP 15K (1005) R1947 1-208-915-81 s RES, CHIP 15K (1005) 7-40 HXCU-FB70...
Page 157
1-208-927-81 s RES, CHIP 47K (1005) R2076 1-208-911-81 s RES, CHIP 10K (1005) R2012 1-208-927-81 s RES, CHIP 47K (1005) R2077 1-208-911-81 s RES, CHIP 10K (1005) R2013 1-208-927-81 s RES, CHIP 47K (1005) R2078 1-208-911-81 s RES, CHIP 10K (1005) 7-41 HXCU-FB70...
Page 158
1-218-990-81 s CONDUCTOR, CHIP (1005) R2245 1-216-813-91 s RES, CHIP 220 (1608) R2147 1-208-923-81 s RES, CHIP 33K (1005) R2246 1-216-813-91 s RES, CHIP 220 (1608) R2148 1-208-911-81 s RES, CHIP 10K (1005) R2247 1-216-813-91 s RES, CHIP 220 (1608) 7-42 HXCU-FB70...
Page 159
1-208-903-81 s RES, CHIP 4.7K (1005) R2419 1-208-863-81 s RES, CHIP 100 (1005) R2345 1-208-863-81 s RES, CHIP 100 (1005) R2420 1-208-863-81 s RES, CHIP 100 (1005) R2346 1-208-863-81 s RES, CHIP 100 (1005) R2421 1-208-887-81 s RES, CHIP 1.0K (1005) 7-43 HXCU-FB70...
Page 160
1-208-875-81 s RES, CHIP 330 (1005) R2631 1-208-895-81 s RES, CHIP 2.2K (1005) R2558 1-208-855-81 s RES, CHIP 47 (1005) R2632 1-208-911-81 s RES, CHIP 10K (1005) R2559 1-208-871-81 s RES, CHIP 220 (1005) R2633 1-208-919-81 s RES, CHIP 22K (1005) 7-44 HXCU-FB70...
Page 161
1-208-855-81 s RES, CHIP 47 (1005) RB606 1-234-370-21 s RES, NETWORK 22 (1005X4) RB607 1-234-370-21 s RES, NETWORK 22 (1005X4) R2705 1-208-863-81 s RES, CHIP 100 (1005) RB608 1-234-370-21 s RES, NETWORK 22 (1005X4) R2723 1-220-870-81 s RES, CHIP 10 (1005) 7-45 HXCU-FB70...
Page 162
1-234-372-21 s RES, NETWORK 100 (1005X4) RB1108 1-234-373-21 s RES, NETWORK 220 (1005X4) RB746 1-234-372-21 s RES, NETWORK 100 (1005X4) RB1109 1-234-373-21 s RES, NETWORK 220 (1005X4) RB747 1-234-372-21 s RES, NETWORK 100 (1005X4) RB1110 1-234-373-21 s RES, NETWORK 220 (1005X4) 7-46 HXCU-FB70...
Page 163
6-503-067-02 s DI LF-3011MKN THP105 1-803-615-21 s THERMISTOR, POSITIVE 6-503-067-02 s DI LF-3011MKN THP106 1-804-458-21 s THERMISTOR, POSITIVE 6-503-067-02 s DI LF-3011MKN THP107 1-804-616-21 s THERMISTOR, POSITIVE THP108 1-804-616-21 s THERMISTOR, POSITIVE 6-503-067-02 s DI LF-3011MKN THP109 1-803-615-21 s THERMISTOR, POSITIVE 7-47 HXCU-FB70...
Page 164
1-165-467-21 s CAP, ELECT 47MF 8X10 1-218-977-81 s RES, CHIP 100K C131 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 1-218-977-81 s RES, CHIP 100K C132 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 R055 1-218-965-81 s RES, CHIP 10K 1005 7-48 HXCU-FB70...
Page 165
1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 1-100-581-81 s CAP,CHIP CERAMIC0.0047MF B1005 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 7-49 HXCU-FB70...
Page 166
1-414-864-21 s FERRITE, EMI (SMD) (1608) 1-414-864-21 s FERRITE, EMI (SMD) (1608) 8-729-928-37 s TRANSISTOR DTA114EE-TL 1-414-864-21 s FERRITE, EMI (SMD) (1608) 8-729-929-09 s TRANSISTOR DTC123JE-TL FB12 1-414-864-21 s FERRITE, EMI (SMD) (1608) 8-729-928-37 s TRANSISTOR DTA114EE-TL 8-729-928-25 s TRANSISTOR 2SA1774TL-QR 7-50 HXCU-FB70...
Page 167
8-729-929-09 s TRANSISTOR DTC123JE-TL 1-208-887-81 s RES, CHIP 1.0K (1005) Q405 8-729-928-37 s TRANSISTOR DTA114EE-TL 1-208-887-81 s RES, CHIP 1.0K (1005) Q406 8-729-929-09 s TRANSISTOR DTC123JE-TL 1-208-887-81 s RES, CHIP 1.0K (1005) 1-208-879-81 s RES, CHIP 470 (1005) 7-51 HXCU-FB70...
Page 168
1-208-895-81 s RES, CHIP 2.2K (1005) R273 1-208-883-81 s RES, CHIP 680 (1005) R179 1-208-919-81 s RES, CHIP 22K (1005) R275 1-208-883-81 s RES, CHIP 680 (1005) R180 1-208-919-81 s RES, CHIP 22K (1005) R277 1-208-887-81 s RES, CHIP 1.0K (1005) 7-52 HXCU-FB70...
Page 169
1-798-385-11 s SWITCH, TACTILE (ILLUMINATED) 1-798-385-11 s SWITCH, TACTILE (ILLUMINATED) 1-762-531-21 s SWITCH, TOGGLE 1-762-531-21 s SWITCH, TOGGLE 1-762-531-21 s SWITCH, TOGGLE 1-762-123-21 s SWITCH, TOGGLE 1-762-531-21 s SWITCH, TOGGLE 1-762-531-21 s SWITCH, TOGGLE 1-571-083-21 s SWITCH, SLIDE 1-762-122-21 s SWITCH, TOGGLE 7-53 HXCU-FB70...
Page 227
The location is described at the end in this section. The location is described at the end in this section. CN-3583 CN-3583 -A SIDE- -B SIDE- SUFFIX: -11 SUFFIX: -11 CN-3582 CN-3582 -A SIDE- -B SIDE- SUFFIX: -11 SUFFIX: -11 10-3 HXCU-FB70...
Page 228
CN-3584 The location is described at the end in this section. CN-3584 CN-3584 -A SIDE- -B SIDE- SUFFIX: -11 SUFFIX: -11 10-4 HXCU-FB70...
Page 239
20 V AC range are suitable. (See Fig. A) To Exposed Metal Parts on Set 1.5 k Z 0.15 μF voltmeter (5.25V) Earth Ground Fig A. Using an AC voltmeter to check AC leakage. HXCU-FB70...