Table of Contents
Advertisement
Input video
3G-SDI
4K
format
mapping
format
1920×1080
–
/50i
1920×1080
–
/59.94i
1920×1080
Level A/B
/50p
–
1920×1080
Level B-
1)
/50i
DS
1920×1080
Level A/B
/59.94p
1920×1080
Level B-
1)
/59.94i
DS
2)
2-SI
3840×2160
Level A/B
/50p
3) 4)
SQ
2)
2-SI
3840×2160
Level A/B
/59.94p
3) 4)
SQ
2)
2-SI
4096×2160
Level A/B
/50p
3) 4)
SQ
2)
2-SI
4096×2160
Level A/B
/59.94p
3) 4)
SQ
1) Only 3D-Dual Stream is supported.
2) 2-sample interleave division
3) Square division
4) SQ will be converted to 2-SI on the sender side.
Notes
If the video formats on the sender side and receiver
side are not properly configured, video cannot be
transmitted.
During 3G-SDI mapping Level B input, signals will be
converted to Level A for output. During Level B-DS
input, signals will be output unchanged as Level B-DS.
Switch number [7] of DIP switch 1 is disabled on units
operating in receiver mode. The 4K video (4096×2160,
3840×2160) output will be fixed at 2-SI on such units.
Downconvert Output Settings
Specify whether to output the video input on the receiver
side in its original format, or whether to downconvert its
resolution for output. By configuring the downconvert
output setting, you can convert the resolution of 4K
video outputs from modality devices and output them
on HD monitors. This allows you to add HD monitors to
a 4K video transmission system.
DIP switch 1
[3]
[4]
[5]
[6]
[7]
OFF
OFF
–
ON
OFF
OFF
OFF
–
ON
ON
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
ON
ON
ON
–
OFF
OFF
ON
ON
OFF
ON
ON
DIP switch 1
Input video
resolution
[8]
OFF
1920×1080
ON
OFF
3840×2160
ON
OFF
4096×2160
ON
1) The resolution is converted as follows.
3840×2160: Outputs with the height and width reduced to
1/2.
4096×2160: Deletes 128 dots from the left and right
(3840×2160), and outputs with the height and width reduced
to 1/2.
Network Settings
Video transmission groups
Configure groups for the senders that will transmit
images and the receivers. A single sender can be grouped
with multiple receivers. When groups are configured on
a unit operating in sender mode, IP addresses are
automatically assigned to the unit's MAIN and SUB
network connectors.
DIP switch 2
Video
transmission
[2]
[3]
groups
OFF
Group 0
OFF
ON
Group 1
OFF
Group 2
ON
ON
Group 3
Receiver IP address
Assign IP addresses to the receiver's MAIN and SUB
network connectors. You can assign addresses regardless
of video transmission groups. Be sure to assign addresses
that are unique from other devices on the network. You
can configure IP addresses via the ON/OFF settings of
switch numbers [5] to [8] of DIP switch 2. For details, see
"DIP Switch Settings" (page 30).
Network connector
Acceptable IP address range
(receiver)
MAIN
192.168.10.100 to 192.168.10.115
SUB
192.168.11.100 to 192.168.11.115
18
Output video resolution
Same as input video resolution
1)
Resolution converted
(1920×1080)
Same as input video resolution
1)
Resolution converted
(1920×1080)
Sender IP
Sender IP
address (MAIN
address (SUB
network
network
connector)
connector)
192.168.10.32
192.168.11.32
192.168.10.33
192.168.11.33
192.168.10.34
192.168.11.34
192.168.10.35
192.168.11.35
Advertisement
Table of Contents
