Playback Operation - Sony 3-270-589-12 (1) Operating Instructions Manual

Note
This function is not available when the Write Inhibit tab of
the disc is set to the recording disabled position, and when
REC INH on page P1 of the function menu is set to "ON".
The REC INH indicator may light when neither of the
above is true if the format of recorded sections on the disc
is not the same as the recording settings of this unit. In this
case, the playback position can be saved to the disc.

Playback Operation

This section describes the following types of playback:
Normal playback: Playback at normal speed
Playback in jog mode: Variable-speed playback, with the
speed determined by the speed of turning the jog dial
Playback in shuttle mode: Variable-speed playback, with
the speed determined by the angular position of the
shuttle dial
Playback in variable-speed mode: Variable-speed
playback, with the speed finely determined by the
angular position of the shuttle dial
Normal playback
First insert a disc.
For details of how to insert a disc, see "Loading and
Unloading a Disc" on page 44.
ACCESS
NETWORK
LOCAL
REMOTE
LEVEL
CH 1 CH 2 CH 3 CH 4
PHONES
PRESET
PREV button
PLAY button
M/MARK1 button and m/MARK2 button
To start playback
Press the PLAY button.
Playback starts.
When two or more clips are recorded on the disc, they are
played back continuously.
Note
No audio is output when non-audio signals are played
back.
52
Playback
F1
F2
F3
VAR
MARK1
MENU
F4 CHAPTER
IN OUT
SUB THUMB
F5 EXPAND
SET RESET
CLIP NAIL JOG
PAGE DISPLAY
CLIP ESSENCE
MENU MARK MARK2
PREV PLAY NEXT STOP REC
SHUTTLE
KEY INHI
VARIABLE
REC
PB
SHIFT
TOP F REV F FWD END STANDBY
NEXT button
STOP button
Jog dial
Shuttle dial
To jump to the next or previous clip, then start
playback
Use the PREV button, NEXT button, jog dial, or shuttle
dial.
To stop playback
Press the STOP button.
If you play back to the end of the last clip, playback
automatically stops.
If, in this state, you press the PLAY button, the message
"ALARM DISC END." appears on the display.
To carry out playback again, move back to the desired clip
using the PREV button, jog dial or shuttle dial.
To set shot marks
While playing back a disc, you can set essence marks such
as SHOT MARK1 and SHOT MARK2 in desired frames.
To set a SHOT MARK1 or SHOT MARK2, hold down the
M/MARK1 or m/MARK2 button and press the SET
button.
To delete or change essence marks, use the supplied PDZ-
1 Proxy Browsing Software. See "Using PDZ-1 Proxy
Browsing Software" in Chapter 4 (page 79) for more
information about installing the PDZ-1 software. See the
online help of PDZ-1 for more information about using
PDZ-1.
You can delete SHOT MARK1 and SHOT MARK2 in the
CHAPTER screen. For details, see "To delete shot marks
at chapter positions" (page 57).
Playback in jog mode
EJECT
In jog mode, you can control the speed of playback by the
speed of turning the jog dial. The playback speed range is
–1 to +2 times normal speed.
To carry out playback in jog mode, proceed as follows.
ACCESS
NETWORK
LOCAL
REMOTE
LEVEL
CH 1 CH 2
PHONES
1
Press the JOG button, turning it on.
2
Turn the jog dial in the desired direction, at the speed
corresponding to the desired playback speed.
Playback in jog mode starts.
3
To stop playback in jog mode, stop turning the jog dial.
F1
F2
F3
MARK1
MENU
F4
CHAPTER
SUB THUMB IN OUT
F5 EXPAND
CLIP NAIL SET RESET
PAGE DISPLAY
CLIP ESSENCE
MENU MARK MARK2
PREV PLAY NEXT STOP REC
KEY INHI
CH 3 CH 4
VARIABLE
REC
PRESET
PB
SHIFT
TOP F REV F FWD END STANDBY
EJECT
VAR
JOG
SHUTTLE
1 2,3