Table of Contents
Advertisement
8
• Setting is disabled when [ACESproxy (Ver. 1.0.1)] is selected for [Picture Mode].
• Operations when [Automatic] is selected are described below.
-
It is set in accordance with the settings if Color Range settings are included in the camera metadata.
-
When HDMI is selected, [Full] or [Limited] is set automatically depending on HDMI signal information.
-
When SDI is selected, the setting is configured according to the settings for [Picture Mode], [Color Gamut], and [Gamma].
Picture Mode
Color Gamut
Gamma
Other than the above
• Operations when [Format] is set to [ICtCp] are described below.
-
When [Color Range] is set to [SDI Full (4-1019)], the signal for [Wave Form Monitor] will change. (For 10-bit images, the [4-1019] signal will be
displayed as [0-1023].)
-
In the following case, if [Picture Mode] has been set differently for the left and right screens, the right screen's [Color Range] setting will be the
same as set for the left screen.
- When displaying a single terminal's input in full-screen
- When displaying "2 Sample Interleave" or "Dual Link 3G-SDI" signals
9
• When [User LUT] is selected, all [CDL] items, [Chroma], and [Blue Only] cannot be changed.
• [ARRI LUT 709] can be selected when [Picture Mode] is set to [ITU-R BT.709] or [User 1–7].
• [ARRI LUT 2020], [ARRI LUT 2020 PQ 1K] or [ARRI LUT 2020 PQ 2K] can be selected when [Picture Mode] is set to [ITU-R BT.2020] or [User 1–7].
• When [ARRI LUT 2020 PQ 1K] is selected, [HDR Range]
• When [ARRI LUT 2020 PQ 2K] is selected, [HDR Range]
10
• It is not possible to set the function after selecting Picture Mode when the right screen is selected. The right screen's setting will be the same as
set for the left screen.
• When [Backlight Control] settings are changed while [Boost Contrast] is [On], the settings for [Backlight Control] when [Boost Contrast] is [Off]
are also changed.
11
• SD-SDI signal is fixed to [Non-constant Luminance].
• In the following case, if [Picture Mode] has been set differently for the left and right screens, [2020 Constant Luminance] is fixed at [Non-Constant
Luminance]. However, if [Color Gamut] for the left and right screens is [ITU-R BT.2020], then the right screen's setting will be the same as set for
the left screen.
-
When displaying a single terminal's input in full-screen
-
When displaying "2 Sample Interleave" or "Dual Link 3G-SDI" signals
12
• Cannot be set when [Picture Mode] is selected in the right screen.
• Cannot be set when [Picture Mode] is the same in both left and right screens.
• When the [Contrast] setting for the left screen is specified as [1000] or less, the luminance of the left and right screens is the same.
13
• Calibration cannot be executed when using DC power.
• When [Luminance] is set to high brightness, it may be calibrated beyond the brightness adjustment range and set lower than the target value,
depending on the [Color Temperature] setting. In that case, set the [Luminance] again.
• Calibration cannot be executed in [Picture Mode] for the right screen.
14
In [Picture Mode] other than [User 1–7], the results of calibration performed at the factory are copied.
Setting Options
Color Range to be Set
DCI-P3
DCI-P3
Cinema Gamut to DCI
DCI-P3+ to DCI
Full
Canon Log (HDR)
Canon Log 2 (HDR)
Canon Log 3 (HDR)
Limited
[SMPTE ST 2084 (PQ)] settings become [1000].
[SMPTE ST 2084 (PQ)] settings become [2000].
OSD Menu
49
Advertisement
Table of Contents
